MCT 10 Setup Software Contents - Danfoss

1 Contents1 Safety Precautions52 Introduction9 About this Manual9 What is MCT 10 Setup Software ?9 The MCT 10 Setup Software Modules10 Two Versions10 System Requirements11 Background Knowledge11 Related Literature113 Installation and De-installation13 Installation and De-installation13 How to Start the Installation Program13 How to Change Language after Installation134 Introduction to User Interface15 MCT 10 Features155 Set-up of Communication19 Serial Configuration21 Profibus DPv1 Data Communication23 Profibus DPv1 Data Communication23 Profibus DPv1 configuration24 USB Data Communication25

2 USB Data Communication25 Ethernet-TSC Data Communication26 Ethernet-TSC Data Communication26 Ethernet-TSC Configuration266 Parameter Handling27 Set-up27 Parameter View Settings31 Filters32 Parameter Filters33 Special Parameters37 Parameter Edit38 Inline Edit38 Dialog Based Edit38 Comparison of Parameters39 Read Frequency Converter Database40 MCT 10 Setup SoftwareContentsMG10R302 - VLT is a registred Danfoss trademark17 Read/Write between MCT 10 and Frequency Converter45 Reading and Writing Parameters45 Read/Write Settings45 Read From Drive47 Write to Drive49 Views49 Scan49 Scan Configuration49 Scan Network50 Poll518 Saving Data53 Network and Project Folders53 Changing the Set-up of a Device in the Field53 How to Save Data53 Save Changes to a Hard Disk53 Save a Project539 SyncPos55 SyncPos Handling55 Programs and Configuration File55 Import and Export of a Configuration File56 Edit and Save Configuration File57 Import and Export of Programs58 Autostart59 Source Code59 Edit Source

3 Code59 Save and Exit Program60 SyncPos Read From Drive61 SyncPos Write to Drive6210 Import of Files63 Import of Older Dialog Files6311 Printing6512 Alarm, Warning and Fault Log Readout67 Localisation of Alarms and Warning67 Handling Alarms/Warnings in Project Files69 Handling the Alarms and Warning Loggings6913 Smart Logic Controller Plug-in71 Smart Logic Controller Plug-in71 ContentsMCT 10 Setup Software2MG10R302 - VLT is a registred Danfoss trademarkComponents simple to learn7214 Scope Function73 Introduction to the Scope Function73 Activating the Scope73 Channel Types73 Initial "Add Channel" (PC Polling Channel)

4 74 Initial "Add Channel" (Drive Real Time Channel)77 Using Advanced Triggers in a "Drive Real78 Communication Control79 Additional Settings80 Triggers82 Trigger Position82 Cursors8315 Update Drives Firmware Support in MCT 1085 Background Details85 How to Find Out if MCT 10 Has Been Updated8616 Guide to DP V1 Connection and Simatic Manager8717 FC 102 and FC 202 Series Functions97 New Features97 Clock Features97 Date and Time97 Working Days98 Preventive Maintenance99 Times Actions99 Quick Menus10018 VLT to FC Series Converter Function101 Import

5 Drive from Excel10219 Troubleshooting103 Save Error Dialog103 Common Problems and Solutions104 Changes Are Not Saved to PC104 Error Message Whilst Installing MCT 10 Setup Software104 Error Message Communication Failed104 MCT 10 Setup SoftwareContentsMG10R302 - VLT is a registred Danfoss trademark31 Safety PrecautionsMCT 10 Setup Software4MG10R302 - VLT is a registred Danfoss trademark1 1 Safety Copyright, Limitation of Liability and Revision RightsThis publication contains information proprietary to Danfoss .

6 By accepting and using this manual the user agrees that the information contained hereinwill be used solely for operating equipment from Danfoss or equipment from other vendors provided that such equipment is intended for communicationwith Danfoss equipment over a PROFIBUS serial communication link. This publication is protected under the Copyright laws of Denmark and most does not warrant that a Software program produced according to the guidelines provided in this manual will function properly in every physical,hardware or Software Danfoss has tested and reviewed the documentation within this manual, Danfoss makes no warranty or representation, either express or implied,with respect to this documentation, including its quality, performance.

7 Or fitness for a particular no event shall Danfoss be liable for direct, indirect, special, incidental, or consequential damages arising out of the use, or the inability to use informationcontained in this manual, even if advised of the possibility of such damages. In particular, Danfoss is not responsible for any costs including but not limitedto those incurred as a result of lost profits or revenue, loss or damage of equipment, loss of computer programs, loss of data, the costs to substitutethese.

8 Or any claims by third reserves the right to revise this publication at any time and to make changes in its Contents without prior notice or any obligation to notifyprevious users of such revisions or this Software package you can remote-control the frequency converter, thereby starting an electric motor which may act as adrive for dangerous the necessary caution must always be observed when using the Software , and suitable measures should be taken to preventinjury and damage to machinery and 10 Setup Software1 Safety PrecautionsMG10R302 - VLT is a registred Danfoss trademark5 Safety Safety PrecautionsThe voltage of the frequency converter is dangerous whenever connected to mains.

9 Incorrect installation of the motor, frequencyconverter or fieldbus may cause damage to the equipment, serious personal injury or death. Consequently, the instructions in thismanual, as well as national and local rules and safety regulations, must be complied mains supply to the frequency converter must be disconnected whenever repair work is to be carried out. Check that the mains supply hasbeen disconnected and that the necessary time has elapsed before removing motor and mains supply [OFF]

10 Button on the control panel of the frequency converterr does not disconnect the mains supply and consequently it must not be usedas a safety equipment must be properly earthed, the user must be protected against supply voltage and the motor must be protected against overloadin accordance with applicable national and local earth leakage current exceeds against motor overload is not included in the factory setting. If this function is desired, set par. 1-90 Motor Thermal Protection todata value ETR trip 1 [4] or data value ETR warning 1 [3].