Metal Film Resistors, Axial, Military, MIL-R-10509 ...

1 CMF (Military RN and RL) Dale Revision: 16-Sep-161 Document Number: 31027 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT Film Resistors, axial , Military, MIL-R-10509 Qualified, Precision, Type RN and MIL-PRF-22684 Qualified, Type RLFEATURES Very low noise (-40 dB) Very low voltage coefficient (5 ppm/V) Controlled temperature coefficient Flame retardant epoxy coating Commercial alternatives to military styles are available with higher power ratings. See CMF Industrial data sheet: ( )Notes(1)Continuous working voltage shall be or maximum working voltage, whichever is less.

2 (2)Formerly rated at 1 W and is the direct replacement for RN70 of MIL-R-10509 rev. D.(3)Tolerances of %, % and % are not applicable to characteristic ELECTRICAL SPECIFICATIONSGLOBAL CWPOWERRATINGP125 (1)VRESISTANCERANGE MIL-R-10509 100 ppm/ C(D)RESISTANCERANGE MIL-R-10509 50 ppm/ C(C)RESISTANCERANGE MIL-R-10509 25 ppm/ C(E)RESISTANCERANGE MIL-PRF-22684 TOL. (3) % to 100K10 to , , , to to to , , , to to to , , , to to to , , , (2) to to to , , , to 150K2, to 470K2, 5700 TECHNICAL SPECIFICATIONSPARAMETERUNITCONDITIONV oltage Coefficientppm/V5 when measured between 10 % and full rated voltageInsulation Resistance 1010 min.

3 Dry; 108 min. after moisture testOperating Temperature Range C-65/+175 (see derating curves for military range)Terminal StrengthIb5 pound pull test for RL07/RL20; 2 pound pull test for all othersSolderabilityContinuous satisfactory coverage when tested in accordance with MIL-R-10509 and MIL-PRF-22684P x RCMF (Military RN and RL) Dale Revision: 16-Sep-162 Document Number: 31027 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT For additional information on packaging, refer to the Through Hole resistor Packaging document ( ).

4 APPLICABLE MIL-SPECSMIL-R-10509 and MIL-PRF-22684: The CMF models meet or exceed the electrical, environmental and dimensional requirements of MIL-R-10509 and MIL-PRF-22684. Noise: Vishay Dale Metal film resistors have exceptionally low noise level. Average for standard resistance range is V per V over a decade of frequency, with low and intermediate resistance values typically below V per V. GLOBAL PART NUMBER INFORMATIONMIL STYLETOLERANCE CODERN50E = 25 ppm3 digit significantB = %RN55 C = 50 ppmfigure, followed byC = % D = %0R01 = 10 2512 = k 2494 = M New Global Part Numbering: RN60D3483FR36 (preferred part numbering format) RN 6 0D 3 4 8 3 F R 3 6 Historical Part Number example.

5 RN60D3483F (will continue to be accepted)3483 DRN60 MIL STYLECHARACTERISTICRESISTANCE VALUETOLERANCE CODEPACKAGINGRN65RN70RN60 = 100 ppma multiplierDF = 1 %Blank = standard(Dash number)88 = hot solder dip143 = non-magneticR36 FPACKAGING SPECIALCHARACTERISTICRESISTANCEVALUEB14 = tin/lead, bulkBSL = tin/lead, bulk,single lot date codeR36 = tin/lead, T/R (full)RE6 = tin/lead, T/R (1000 pieces)RSL = tin/lead, T/R,single lot date codeUse R for values < 100 MIL STYLETOLERANCECODEPACKAGING RL07S = solderable2 digit significantG = 2 %B14 = tin/lead, bulkBSL = tin/lead, bulk, single lot date codeR36 = tin/lead, T/R (full)RE6 = tin/lead, T/R (1000 pieces)RSL = tin/lead, T/R, single lot date codeRL20figure, followed byJ = 5 %a multiplier4R3 = 202 = k 474 = 470 k New Global Part Numbering: RL07S471JR36 (preferred part numbering format)Historical Part Number example.

6 RL07S471J (will continue to be accepted)MIL STYLELEAD MATERIALRESISTANCE VALUETOLERANCE CODEPACKAGINGRL0 7S471JR36RL07S471JR36 LEAD MATERIALRESISTANCEVALUEUse R for values < 10 SPECIALB lank = standard(Dash number)88 = hot solder dip143 = non-magneticMATERIAL SPECIFICATIONSE lementNickel-chrome alloyCoatingFlame retardant epoxy, formulated for superior moisture protectionCoreFire-cleaned high purity ceramicTerminationStandard lead material is solder-coated copper. Solderable and weldable. CAGE CODE: 91637 ENVIRONMENTAL SPECIFICATIONSG eneralEnvironmental performance is shown in the Environmental Performance table. Test methods are those specified in MIL-R-10509 and LifeResistance shifts due to storage at room temperature are negligible.

7 CMF (Military RN and RL) Dale Revision: 16-Sep-163 Document Number: 31027 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT Dale CMF resistors have an operating temperature range of -65 C to +175 C. They must be derated according to the following curves:DIMENSIONS in inches (millimeters)Note(1)Lead length for product in bulk pack. For product supplied in tape and reel, the actual lead length would be based on the body size, tape spacing and lead Commercial equivalents of military styles are available with higher power ratings.

8 Consult factory. (1)Formerly rated at 1 W and is the direct replacement for RN70 of MIL-R-10509 rev. DALE MODELABC(MAX.) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( )MILITARY POWER RATINGWATTAGEMILITARY QUALIFIEDMIL-R-10509 MIL-PRF-22684AT +70 C(D)AT +125 C(C and E)AT +70 (1)RN70--REWOP DETAR FO %AMBIENT TEMPERATURE C120100806040200 MIL-R-10509 Char. C and E RatingMIL-R-10509 Char. D RatingMIL-PRF-22684 DERATING170150130110907050 ABDC(Max.)

9 (1)( )CMF (Military RN and RL) Dale Revision: 16-Sep-164 Document Number: 31027 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT RL series are color banded per MIL-PRF-22684. MARKING (per MIL-PRF-10509)Characteristics: D = 100 ppm, C = 50 ppm, E = 25 ppmTolerance: F = 1 %, D = %, C = %, B = %Value = Three significant figures and multiplierJ = JAN (Joint Army - Navy) brandRN50: (3 lines)RN55, RN60, RN65, RN70 (4 lines)J50D1211F137 JAN, type, characteristicValueTolerance and 3 digit date codeDALE 0137J RN55D 1211F Company logo4 digit date code and JAN brandType and characteristicValue and TolerancePERFROMANCEREQUIREMENTMIL-R-105 09 MIL-PRF-22684 CHARACTERISTIC DCHARACTERISTIC CCHARACTERISTIC EMIL Temperature Coefficient+200 ppm/ C -500 ppm/ C 50 ppm/ C 25 ppm/ C 200 ppm/ CApplicable Vishay Dale Temperature Coefficient 100 ppm/ C 50 ppm/ C 25 ppm/ C 200 ppm/ Shock % R % R % R % RShort Time Overload % R % R % R % RLow Temperature Operation % R % R % R % RMoisture Resistance % R % R % R % RShock % R % R

10 % R % RVibration % R % R % R % RLoad Life % R % R % R % RDielectric Withstanding Voltage % R % R % R % REffect of Solder % R % R % R % RTHERMAL RESISTANCE020406080100120 APPLIED POWER IN WHEAT RISE ( C ABOVE AMBIENT)0 1 CMF65,CMF70 CMF50 CMF55 CMF60 CMF20 CMF07 Legal Disclaimer Revision: 08-Feb-171 Document Number: 91000 Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, Vishay ), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product.