Metallic industrial piping - Part 5: Inspection and testing

1 EUROPEAN STANDARDNORME EUROP ENNEEUROP ISCHE NORMEN 13480-5 May 2002 ICS versionMetallic industrial piping - part 5: Inspection and testingTuyauteries industrielles m talliques - Partie 5: Inspectionet contr leMetallische industrielle Rohrleitungen - Teil 5: Pruf ngThis European Standard was approved by CEN on 23 May members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration.

2 Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden.

3 Switzerland and United COMMITTEE FOR STANDARDIZATIONCOMIT EUROP EN DE NORMALISATIONEUROP ISCHES KOMITEE F R NORMUNGM anagement Centre: rue de Stassart, 36 B-1050 Brussels 2002 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national No. EN 13480-5:2002 ELicensed Copy: sheffieldun sheffieldun, na, Thu Sep 21 06:58:47 BST 2006, Uncontrolled Copy, (c) BSIEN 13480-5:2002 (E)Issue 1 (2002-05) ..52 Normative references ..53 Terms and and abbreviations.

4 65 Determination of Inspection and testing requirements .. of piping .. and Inspection procedures ..76 Design validation .. and extent .. calculations .. schedule .. of design design review .. of design documentation .. procedures/qualifications .. proof of safety .. s declaration of design compliance ..107In-process Inspection and testing .. and formed pressure retaining parts .. of material .. of formed pressure retaining parts .. testing of formed parts .. testing of formed parts .. approvals.

5 Of welding set-up .. and Inspection during welding .. after treatment ..128 Non- destructive testing of welds .. of .. of weld quality by sample revealed by sample Inspection .. butt, branch, fillet and seal of examination .. metal joints .. welds .. Methods .. criteria .. qualification ..21 Licensed Copy: sheffieldun sheffieldun, na, Thu Sep 21 06:58:47 BST 2006, Uncontrolled Copy, (c) BSIEN 13480-5:2002 (E)Issue 1 (2002-05) of NDT method .. repairs ..229 Final assessment and Inspection before the proof test.

6 Inspection after the proof test .. of the manufacturing documents .. test .. pressure test .. pressure test .. tests .. of the proof test .. of safety documentation package .. and manufacturing documentation package .. instructions .. for the purchaser ..3010 Declaration/Certification ..30 Annex A (informative) Inspection of safety systems ..31 Annex ZA (informative) Clauses of this European Standard addressing essential requirements orother provisions of EU directives..32 Licensed Copy: sheffieldun sheffieldun, na, Thu Sep 21 06:58:47 BST 2006, Uncontrolled Copy, (c) BSIEN 13480-5:2002 (E)Issue 1 (2002-05)4 ForewordThis document (EN 13480-5.)

7 2002) has been prepared by Technical Committee CEN/TC 267 " industrial piping andpipelines", the secretariat of which is held by European Standard shall be given the status of a national standard, either by publication of an identical text orby endorsement, at the latest by November 2002, and conflicting national standards shall be withdrawn at the latestby November document has been prepared under a mandate given to CEN by the European Commission and the EuropeanFree Trade Association, and supports essential requirements of EU Directive(s).

8 For relationship with EU Directive(s), see informative annex ZA, which is an integral part of this this standard the Annex A is informativeThis European Standard EN 13480 for Metallic industrial piping consists of seven interdependent and not dissociableparts which are: part 1: General. part 2: Materials. part 3: Design. part 4: Fabrication and installation. part 5: Inspection and testing . part 6: Additional requirements for buried 13480-7, Guidance on the use of conformity assessment proceduresAccording to the CEN/CENELEC Internal Regulations, the national standards organizations of the followingcountries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain,Sweden, Switzerland and the United Copy.

9 Sheffieldun sheffieldun, na, Thu Sep 21 06:58:47 BST 2006, Uncontrolled Copy, (c) BSIEN 13480-5:2002 (E)Issue 1 (2002-05)51 ScopeThis part of this European Standard specifies the requirements for Inspection and testing of industrial piping asdefined in EN 13480-1:2002 to be performed on individual spools or piping systems, including supports, designed inaccordance with EN 13480-3 and prEN 13480-6 (if applicable), and fabricated and installed in accordance withEN Normative referencesThis part of this European Standard incorporates by dated or undated reference, provisions from otherpublications.

10 These normative references are cited at the appropriate places in the text and the publications arelisted hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply tothis part of this European Standard only when incorporated in it by amendment or revision. For undated referencesthe latest edition of the publication referred to applies (including amendments).EN 287-1, Approval testing of welders Fusion welding part 1: 288-2, Specification and approval of welding procedures for Metallic materials - part 2: Welding procedurespecification for arc 473:2000, Non destructive testing - Qualification and certification of NDT personnel General 571-1, Non destructive testing Penetrant testing part 1: General 970, Non- destructive examination of fusion welds Visual 1289.