Microwave Drawer : SMD2470AS, SMD3070AS InstallatIon …

1 1 SPECIAL WARNINGINSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED : SAVE this InstallatIon manual FOR LOCAL ELECTRICAL INSPECTOR S AND SAVE THESE INSTRUCTIONS FOR FUTURE ANd dImENSIoNSFor SAFETY CONSIDERATIONS do not install Drawer in any combustible cabinetry, which is not in accord with the stated clearances and dimensions on pages 2 - 5. See Figure 1 (for 24") or Figures 4 and 5 (for 30"). Microwave Drawer : SMD2470AS, SMD3070 ASInstallatIon ManualUNPACkING yoUR Microwave Drawer Remove all packing materials from inside the Microwave Drawer . DO NOT REMOVE THE WAVEGUIDE COVER, which is located on the top of the Microwave Drawer . Remove the feature sticker, if there is one.

2 Check the Drawer for any damage, such as misaligned or bent Drawer , damaged Drawer seals and sealing surfaces, broken or loose Microwave Drawer guides and dents inside the cavity or on the front side of the Drawer . If there is any damage, do not operate the Microwave Drawer and contact your dealer or a SHARP AUTHORIZED NotES to thE INStALLER Read all of the InstallatIon Manual before installing the Microwave Drawer . Remove all packing material before connecting the electrical s u p ply. Observe all governing codes and ordinances. Be sure to leave these instructions with the NotES to thE CoNSUmERKeep this manual with your Operation Manual for future reference.

3 As when using any Microwave oven generating heat, there are certain safety precautions you should follow. These are listed in the Operation Manual. Read all and follow carefully. Be sure your Microwave Drawer is installed and grounded properly by a qualified installer or service SAfEty INStRUCtIoNS If the information in this manual is not followed exactly, a fire or electrical shock may result that could cause property damage, personal injury or death. To reduce the risk of tipping, the Microwave Drawer must be secured by a properly installed Anti-Tip block. This Microwave Drawer must be electrically grounded in accordance with local codes.

4 Make sure the wall coverings and the cabinets around the Microwave Drawer can withstand the heat generated by the Microwave Drawer . Never leave children alone or unattended in the area where a Microwave Drawer is in use. Never leave the Drawer open when the Microwave is unattended. Stepping, leaning or sitting on the Drawer may result in serious injuries and can also cause damage to the Microwave Drawer . Do not use the Microwave Drawer as a storage space. This creates a potentially hazardous situation. Check that the time-of-day is in the display. If not, touch STOP/CLEAR to prevent unintended coverSealing surfaceOven cavitySealing surface 2 ABCDEFGHIJCLEARANCES ANd dImENSIoNS Dimensions that are shown in Figure 1 (for 24") or Figures 4 and 5 (for 30") must be used.

5 Given dimensions provide minimum clearance. Locate electrical outlet in the shaded area in the upper left-hand corner of the cutout. See Figure 9. Contact surface must be solid and level. Pay special attention to the floor on which the Microwave Drawer will sit. The floor of the opening should be constructed of plywood strong enough to support the weight of the oven (about 100 pounds). Check location where the Microwave Drawer will be installed for proper electrical supply. Your oven can be built into a cabinet or wall by itself or under a gas or electric wall oven. Be sure that the clearance of the floor between the wall oven and the Microwave Drawer is a minimum of 2-inches.

6 The Microwave interior will easily accommodate a 9" x 13" oblong dish or a bag of Microwave popcorn. The oven can also be mounted flush. Please see instructions for flush mounting included with the Flush Mount Deflector vent. 24" Microwave Drawer mEASUREmENtSBCGDBCDEFGHIIJKLMNOPAQAFEF igure 1 Figure 2 Cutout Dimension 22 1/8" x 15 9/16"A. 6"B. Suggested electrical outlet location*C. Anti-Tip blockD. 5"E. 3-1/2"F. 4"G. 22-1/8" openingH. 14-13/16" to bottom of Anti-Tip blockI. Allow 7/8" overlapJ. 23-1/2" minimum depthK. Allow 3/16" overlapL. 36" countertop heightM. Allow 7/16" minimum overlapN. Floor must support 100 lbO. 24" cabinet minimumP.

7 15-9/16" openingQ. Allow 1/8" overlapFigures 1 and 2 contain many Microwave Drawer measurements for reference when planning the Drawer s Microwave Drawer can be installed below any electric or gas wall oven.* Can also be installed using an electrical outlet in an adjacent cabinet within the area where the provided electrical cord can reach. Power cord access hole in cabinet should be a minimum 1 1/2" diameter hole and deburred of all sharp edges. IMPORTANT Always allow sufficient power cord length to the electrical outlet to prevent tension. Always check electrical codes for 21-5/8"B. 4 -11/16"C. 1-3/4"D. 21-7/8"E. 23-7/8"F. 15 -7/ 8"G.

8 14 -19/32"H. 1-9/64" door thicknessI. 15" auto Drawer openingJ. 4" 3 BCGDBCDEFGHIIJKLMNOPAQAFEThis drawing represents a typical standard cabinet. If installed in custom cabinets with extended counter tops, take into account visibility and access to controls. See Figure oven location downward for extended countertopsExtended countertopsFigure 3A. 25"B. 1/2" minimumC. 15-7/8"D. 36"E. Control panel shown in open positionF. 2 4"G. 34 -1/2" 4 Figures 4, 5 and 6 contain many Microwave Drawer measurements for reference when planning the Drawer s Microwave Drawer can be installed below any electric or gas wall " Microwave Drawer mEASUREmENtSABCDEFGHIJKLMMNOPQRF igure 4A.

9 84" wall cabinetB. Optional wall oven cutout illustrated in sketchC. Suggested electrical outlet location*D. 6"E. Anti-Tip blockF. 3 -1/ 2"G. 5"H. 4"I. 2" minimumJ. 28-7/16" openingK. Allow 3/16" overlapL. 14-13/16" to bottom of Anti-Tip blockM. Allow 23/32" overlapN. 23-1/2" minimum depthO. 15-9/16" open ingP. Allow 1/8" overlapQ. Floor must support 100 lbR. 30" cabinet minimum* Can also be installed using an electrical outlet in an adjacent cabinet within the area where the provided electrical cord can reach. Power cord access hole in cabinet should be a minimum 1 1/2" diameter hole and deburred of all sharp edges.

10 IMPORTANT Always allow sufficient power cord length to the electrical outlet to prevent tension. Always check electrical codes for Dimension 28 7/16" x 15 9/16"5 ADGHECJFIBABDFGEHPKNOJIILCMQF igure 5 Figure 6A. 6"B. Suggested electrical outlet location*C. Anti-Tip blockD. 5"E. 3-1/2"F. 4"G. 28-7/16" openingH. 14-13/16" to bottom of Anti-Tip blockI. Allow 23/32" overlapJ. 23-1/2" minimum depthK. Allow 3/16" overlapL. 36" countertop heightM. Allow 7/16" overlapN. Floor must support 100 lbO. 30" cabinet minimumP. 15-9/16" open ingQ. Allow 1/8" overlapA. 21-5/8"B. 4 -11/16"C. 1-3/4"D. 21-7/8"E. 29-7/8"F. 15 -7/ 8"G. 14 -19/32"H.