MILITARY STANDARD <.< ENGINEERING ... - Product lifecycle

1 , -. _. \. DOD-STD-OOIOOD(AR). 3 APRIL 1987. O USED. DOD- IN LIEU OF. STD-1 OOC. 22 DECEMBER 1978.. MILITARY STANDARD .. <.< ENGINEERING DRAWING PRACTICES. \.. ANsc ti/A. AREA DRPR. f) ISTRIBUTION STATEM~ . APPROVED FOR PUBLIC RELEASE ; DISTRIBUTION IS UNLIMITED. A. DOD-STD-001 OOD(AR ). \. DEPARTMENT OF DEFENSE. WASHINGTON, DC 20301. ENGINEERING Drawing Practices DOD-STD-00 100D(AR ). 1. This MILITARY STANDARD is approved for uae by all elements of the U;S. Army Tank-Automotive Command and Army Armament, Munitions and Chemical Command. 2. genef icial comments (recommendation, additiona, deletions) and anY . pertinent data which ay be of use in improving this document should be addreaaed to: Commander, IJ. S. Army Armament Research, Development and ENGINEERING Center, ATTN: SMCAR-ESC-S, Picatinny Arsenal, NJ 07306-5000, by . using the self-addreaaed Standardization Oocument Improving Proposal (DD Form 1426) appearing at the end of this document or by letter.

2 0. 4.. ii a DOD-STD-00 10OD (AR). foiimosu). This interim MILITARY STANDARD provides: Drawing Dractioes for preparation of ENGINEERING drawings and drawing fotiat mat=riale. Definitions and examplea of types of ENGINEERING drawings to be prepared for the Department of Defense. These are cataloged for appropriate selection and uee. in support of Levels of ENGINEERING drawings being prepared under the requirements of DOD-D-1 OOO. Procedures for the creation of titles for ENGINEERING drawings. Numbering, coding and identification procedures for ENGINEERING drawings, associated lists and-documents referenced on these ENGINEERING drawings and aafiociated 1iste. Methods for revision of ENGINEERING drawings and methods for recording of such revisiona. Requirements for preparation of associated lists. This docwment applies to all TACOM and AMCCOM contracta which specify delivery of Level 3 drawings in accordance with DOD-D-1000.

3 All drawings. which define the Product %seline shall conform to Level 3. Level 3 drawings should also be acquired for definition of the Allocated Baaeline. iii DOD-STD-00 IOOD(AR). THIS PA(X IEFC BLANK INTENTIONALLY. \. iv DOD-STD-00 10OD(AR). SCOPE. o This STANDARD revision prescribes of ENGINEERING general drawings requirements and associated for the preparation lists prepared and by or for elements of Army Tank-Automotive Command and Army Armament, Munitions and Chemical Command. 1. DOD-STD-00 100D(AR). REFERENCED DOCUMENTS. Government documents. c Speclf Icatlons, standards, and handbooks. Unless otherwise specified, the following speoif ications, standards, and handbooks of the issue listed in that issue OF the Department of Defense Index of Specifications and Standards (DoDISS) specific in the solicitation form a part of this STANDARD to the extent specified herein.)

4 SPECIFICATIONS. Federal L-F-340 Film, Diazot ype, Sensitized, Moist and try Process, Roll and Sheet L-P-5 19 Plastic Sheet, Tracing, Glazed and Matte Finish TT-I-1795 Ink, Marking, Stencil, Opaque (Porous and Non Porous Surf aces). UU-P-221 Paper, Direct Positive Sensitized, (Diazotype - Moist and Dry Process). UU-P-561 Paper, Tracing CCC-C-531 Cloth, Tracing Militar~. DOD-D-1 000 tiawings, ENGINEERING and Associated Lists MIL-D-5480 Data, ENGINEERING and Technical, Reproduction Q). sRequirements for MIL-H-6088 Heat Treatment of. Aluminun Alloys MIL-S-6090 Steel, Carburizing and Nitriding, Procesees for MIL-H-6875 Heat Treatment of Steel, Process for MIL-O-851O Drawing, Undimensioned, Reproducible, Photographic and Contact, Preparation of NIL-M-9868 Microfilming of ENGINEERING Dccuments, 35mm Requirements for MIL-W-1 3855 Weapon, Small Arms and Airoraft Armament Subsystems, General Speoif ioation for MIL-M-3851O Microcircuits, General Specification for 2.

5 DOD-STD-00 10OD (AR). APPLICABLE DOCUMENTS (tint' d). SPECIFICATIONS. MILITARY MIL-M-38761 Microfilming and Photographing of ENGINEERING / . Technical Data and Related Documents: PCAM. Card Preparation, ENGINEERING Data Micro-repro- duction System, General Requirements for, Preparation of MIL-P-55010 Plastic Sheet, Polyethylene Terephthalate STANDARDS. MILITARY MIL-STD-12 Abbrev i at ion for Use on Drawings, Specifications, Standards and in Technical Documents MIL-STD-14 Architectural Symbols MIL-STD-15-2 Electrical Wiring Equipment Symbols for Shipst Plans MIL-STD-17-1 Mechanical Symbols MIL-STD-17-2 Mechanical Symbols for Aeronautical, Aerospace- craft and Spacecraft Use MIL-STD-25 Ship Structural Symbols for Use on Ship Drawings MIL-STD-34 Preparation of Drawings for Optical Elements and Optical Systems, Oeneral Requirements for DOD-STD-100 ENGINEERING Drawing Practices MIL-STD-129 Marking for Shipment and Storage MIL-STD-130 Identification Marking of MILITARY Property MIL-STD-171 Finishing of Metal and Wood Surfaces MIL-STD-190 Identification Marking of Rubber Products MIL-sTD-275 Printed Wiring for Electronic Equipment DOD-STD-48O Configuration Control - ENGINEERING Changes.

6 Deviations and Waivers DOD-STD-OO1 OOD(AR). APPLICABLE DOCUMENTS (Contld). STANDARDS. MILITARY MIL-STD-481 Configuration Control - ENGINEERING Changes, Deviations and Waivers (Short Form). MIL-STD-490 Specification Practices MIL-STD-681 Identification Coding and Application of Hookup and Lead Wire MIL-STD-961 MILITARY Specifications and Associated Documents, Preparation of MIL-STD-1 174 Associated Lists for ARRADCOM ENGINEERING Drawings MIL-STD-1267 Dimensioning of Barrel Chambers of Small Arms Weapons MIL-STD-1 306 Fluerics Terminology and Symbols MIL-STD-1 464 Army Nomenclature System DOD-STD-1 476. DOD-STD-1686. Metric System, Electrostatic Protection Application Discharge of Electrical Control in Program and Electronic for New Design Parts, 0. Assemblies, and Equipment (excluding Electrically Initiated Explosive Devices) (Metric). DOD-STD-2 167 Defense System Software Development MIL-STD-21 75 Castings, Classification and Inspection of HANDBOOKS.

7 DOD-HDBK-263 Electrostatic Discharge Control Handbook for Protection of Electrical and Electronic Parts, Assemblies and Equipment (Excluding Electrically Initiated Explosive Devices) Metric Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this STANDARD to the extent specified herein. 12579607 Geometric Symbols for Dimensioning and Tolerancing H4/H8 Commercial and Caernment Entity ( CAGE). H6 Federal Item Name Directory for Supply Cataloging H7 Manufacturers Part and Drawing Number ing Systems 4. DOD-STD-00 10OD (AR). /. DOD DOD Industrial Security Manual for Safeguarding Classified Information - . -4/ . DOD 5230. 25-PH Control MILITARY of Unclassified Technical or Space Application . Data with DODISS Department of Defense Index of Specificatlona and Standards ( Copies of specifications, standards, handbooks, drawings, and publications required by contractors in connection with specific acquisition functions should be obtained from the contracting activity or aa directed by the contracting officer.)

8 Other publications. The following documents form a part of this STANDARD to the extent specified herein. Unless otherwise specified, the issues of the documents which are lbD adopted shall be those listed in the issue of the I&DISS SDeCif led in the solicitation. The issues of documents which have not been a~opted shall be those in ef feet on the date of the cited IbDISS. AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI). ANSI B46. 1-85 Surface Texture (Surface roughness, waviness, and lay). ANSI B92. 1-70 Involute Splines and Inspection WI B92. la-76. ANSI B94. 6-84 Knurling ANSI X3. 5-70 Flowchart Symbols and their Usage in Information Processing. Same as FIPS-24, Federal Information Processing Standards. ANSI Y1 Letter Symbols for Quantities Used in Mechanica of Solids ANSI Y1 Mathematical Signs and Symbols for Use in w/ANSI Y1O. 20a-75 Physical Sciences and Technology ANSI Drawing Sheet Size and Format, ENGINEERING Drawing and Related Documentation Practices ANSI Y14.

9 2M-79 Line Conventions and Lettering, ENGINEERING Drawing and Related Lbcumentation Practices ANSI Y1 Multi and Sectional View Drawings, ENGINEERING Orawings and Related bcumentation Practices ,., ANSI Dimensioning and Toleranclng ANSI Dimensioning and Tolerancing ,, ANS~ Y14. 6-78 Screw Thread Representation ANSI Y14. 6AM Metric Supplement 5. DOD-STD-00 10OD (AR). , . AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI) (tint' d). k -%._+s -A. ANSI Yi? @_ Gear Drawing Standards, Part 1: for Spur, Helical, Double Helical, and Rack, Drafting Practices ANSI Gear and Spline Drawing Standards - Part 2: Bevel and Hypoid Gears, ENGINEERING Drawing and Related Documentation Practices ANSI Mechanical Spring Representation, ENGINEERING Drawing and Related Ibcumentation Fractices ANSI Y1 U. 15-66 Electrical and Electronics Diagrams including Proposed USA Standards for Connection Diagrams and Technical Diagrams ANSI Yl!

10 15a-71 Interconnection Diagrams -1. ANSI Y14. 15b-73 Supplement to ANSI Y snd ANSI Y14. 15a-70. ANSI Y14. 17-66 Fluid Power Diagrans ANSI Y14. Dictionary of Terms for Computer-aided Preparation of Product Definition Data (Including ENGINEERING Drawings), ENGINEERING Drawing and Related Documentation Practices. ANSI Y14. 36-78 Surface Texture Symbols, ENGINEERING Drawing and Related Documentation Practices ANSI Y32. U-77 Graphic Symbols for Plumbing Fixtures for Diagrams. Used in Architecture and Building Construction ANSI Y32. 9-'72 Graphic Symbols for Electric and Layout Drawings Used in Architecture and Building Construction ANSI Y32. 10-67 Graphic Symbols for Fluid Power Diagrams ANSI/AWS A2. ti-79 .Symbols for Welding and Nondestructive Testing- ANSI/IEEE 260-78 Latter Symbols for Units of Measurement (S1. Units, Customary Inch-Pound Units, and Certain Other Units).