Example: marketing

MODEL BRAKE CABLE 04 30 REPLACEMENT - Clicgear

BULLETIN MODEL . BRAKE CABLE . REPLACEMENT 04 SB 1. 10MM. SOCKET. DRIVER. Service Bulletin SB-04 covers the REPLACEMENT of Remove the 10mm Nut from the CABLE Nut Assembly. BRAKE CABLE on the Clicgear Cart, MODEL This should loosen the CABLE and the BRAKE Hammer should swing upwards when free. 2 3 CROSS. SCREW. DRIVER. Disassemble the CABLE Nut Assembly and remove all Unscrew the Lock Screws that secure the CABLE to the components from the CABLE . the Tube. 4 5. For MODEL For MODEL Small CABLE Barrel Large CABLE Barrel CABLE length: CABLE length: 71 (180 cm) 79 (200 cm). BRAKE CABLE BRAKE CABLE Sheath length: Sheath length: 63 (160 cm) 71 (180 cm). Separate the broken Umbrella BRAKE Mount, BRAKE Prepare New BRAKE CABLE Sheath and New CABLE for CABLE Sheath, CABLE and BRAKE Lever from the cart, REPLACEMENT , they are different from those in MODEL remove the CABLE from the BRAKE Lever.

PAGE: 1 OF 3 04 BULLETIN BRAKE CABLE REPLACEMENT 3.0 MODEL SB Service Bulletin SB-04 covers the replacement of Brake Cable on the Clicgear Cart, Model 3.0

Fullscreen Download

Tags:

  Replacement, Cable, Brake, Brake cable 04 30 replacement, Clicgear

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Other abuse

Transcription of MODEL BRAKE CABLE 04 30 REPLACEMENT - Clicgear

1 BULLETIN MODEL . BRAKE CABLE . REPLACEMENT 04 SB 1. 10MM. SOCKET. DRIVER. Service Bulletin SB-04 covers the REPLACEMENT of Remove the 10mm Nut from the CABLE Nut Assembly. BRAKE CABLE on the Clicgear Cart, MODEL This should loosen the CABLE and the BRAKE Hammer should swing upwards when free. 2 3 CROSS. SCREW. DRIVER. Disassemble the CABLE Nut Assembly and remove all Unscrew the Lock Screws that secure the CABLE to the components from the CABLE . the Tube. 4 5. For MODEL For MODEL Small CABLE Barrel Large CABLE Barrel CABLE length: CABLE length: 71 (180 cm) 79 (200 cm). BRAKE CABLE BRAKE CABLE Sheath length: Sheath length: 63 (160 cm) 71 (180 cm). Separate the broken Umbrella BRAKE Mount, BRAKE Prepare New BRAKE CABLE Sheath and New CABLE for CABLE Sheath, CABLE and BRAKE Lever from the cart, REPLACEMENT , they are different from those in MODEL remove the CABLE from the BRAKE Lever.

2 PAGE: 1 OF 3. BULLETIN MODEL . BRAKE CABLE . REPLACEMENT 04 6 7. Insert the New BRAKE CABLE Sheath to the Cart. The New BRAKE CABLE Sheath should pass through the bottom hole of Center Lower Hinge. 8 9 CROSS. SCREW. DRIVER. The lower metal end cap of New BRAKE CABLE Sheath Screw the Lock Screw to secure the New BRAKE CABLE should be inserted into the CABLE Adjust Nut and Bolt. Sheath to the Tube. 10 CROSS 11. SCREW. DRIVER. Install the New CABLE into the BRAKE Lever. Carefully Put the BRAKE Washer to the New CABLE from its end, seat the CABLE Barrel to the BRAKE Lever using a small then insert it to the New BRAKE CABLE Sheath. cross screw driver. PAGE: 2 OF 3. BULLETIN MODEL .

3 BRAKE CABLE . REPLACEMENT 04 3 .0. 12 13 CROSS. SCREW. DRIVER. The BRAKE Washer will be placed between the metal Assemble the BRAKE Lever on New Umbrella BRAKE end cap of New BRAKE CABLE Sheath and the New Mount, push the end of the New BRAKE CABLE Sheath Umbrella BRAKE Mount. and BRAKE Washer into it. 14 15. CROSS. SCREW. DRIVER. Reinstall the two screws that hold the Umbrella BRAKE Push the CABLE bolt with one (1) washer into the BRAKE Mount to the bottom of the tray. hammer with the washer between the CABLE and plastic. Then install the second washer and lock nut on the opposite side of the BRAKE hammer. 16 17. 10MM. SOCKET. DRIVER. Tighten the CABLE lock nut while holding the BRAKE Adjust the BRAKE CABLE until the BRAKE hammer fully hammer in the approximate position shown.

4 Engages the BRAKE gear, as shown, when the BRAKE is in the ON position. PAGE: 3 OF 3.

Show more