MODEL : LK-D30 - aures-support.fr

1 All specifications are subject to change without noticeMini Dot Impact PrinterMODEL : LK-D302 1. Features3 2. Specification4 3. Self Test6 4. User Switches7 5. Command List8 EMULATION epson TM-U2008 EMULATION CITIZEN iDP-35409 EMULATION STAR SP20010 6. Interface11 Interface Connector 11 7. Cash Drawer Connector13 8. Electrical Specifications14 9. Dip Switch Settings15 Table of Contents3 Dip Switch ConfigurationEmulation mode, communications mode, baud rate, serial/parallel handshake, and head printing characteristics are all configured through dip switch settings. Data BufferThe LK-D30 printer has a built-in 16 Kilobyte I/O buffer allowing the host computer to free itself after sending the print data.

2 Reliable communicationsThe LK-D30 supports multiple baud rates, protocols, and handshaking on its parallel & serial interfaces. User controlsA power switch, a paper feed switch, power LED and Paper Low/Out error LED provide ease of use. Self Test ModeA comprehensive self-test mode is available which describes the printer configuration and dip switch setting information along with the version number of firmware installed. Print orientationThe printer is capable of printing normal and upside down, the print orientation is selected by software commands. Selectable international charactersThe LK-D30 supports international characters selectable by software control.

3 Multiple Fonts/SizesTwo different resident fonts are available for printing diversity. Each of these fonts can be printed in normal, double wide, double height, and quadruple sizes. Both fonts and sizes are software selected. Bit image graphicTwo formats for bit mapped graphics are provided. Error detectionThe LK-D30 can detect paper-out and paper-jam as well as paper near-end, controller malfunction, and cover open status. Peripheral DriveTwo cash drawer drivers are provided. Certification(1) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference , and 2) this device must accept any interference received , including interference that may cause undesired operation.

4 (2) UL/cUL (UL 60950-1)(3) MIC(4) CE-EMCD (CE-EMCD Class B should use Parallel shield Cable complied with IEEE-1284 standards)(5) RoHS (TUV)1. Features4 MODELLK-D30 PRINT METHOD9-pin serial impact dot matrixPRINT DIRECTIONBi-directional (with logical seeking)NO. OF COLUMNSE pson Mode : 42/35, 40/33, Star Sp200 : 42/35 Other Modes : 40/32 FONT SIZE7 x 9, 9 x 9 dotsLINE SPACINGn/144 inchPRINTING ( )PRINT SPEED5 Line / Sec (at 40 cpl)INK RIBBONEPSON, ERC-38 compatibleBlack or Purple, Black/RedPAPERM ediaRoll ( )Diameter76mm ( ) max. ( or thick) One Original and one copyDATA BUFFER16K bytesCASH DRAWER DRIVER2 circuits (24V, 1A max)INTERFACERS-232C Serial (25 Pin)USBUSB ComboEthernetWireless LanCentronics Parallel (36 Pin)EMULATIONE pson TM-U200, Citizen iDP-3540 Star SP200 POWER SUPPLYTypeExternal AdaptorInput120 VAC, 230 VACO utput24 VDC X CONDITION5 C to 40 C, 10% to 80% RHSTORAGE CONDITION-20 C to 60 C, 5% to 95% RHRELIABILITYMCBF18 million linesPrinthead150 million charactersDIMENSIONSC utter157(W) X (D) X (H)mmNon cutter157(W) X (D) X (H) lbs ( kg)Non lbs ( kg)2.

5 SpecificationPrinter Specifications5 Overall dimension6 While pressing the paper feed switch for more than 10 seconds after the printer in turned on, the self test mode is initiated. The printer self test includes a listing of the current default settings, read and write test of internal RAM, checksum test of internal program memory, loop back detection statement, a staggered dot line, a few lines of rotating character set, and a diagnostic report. The printer then enters into the On-Line SetupWhen the paper FEED switch is pressed and released instantly as the power is applied to the printer, the printer will print the current printer configuration settings along with the DIP switch information.

6 If the printer setup needs to be changed, turn the Power Off before changing the printer will be setup at the factory as follows;Printer is setup as follows: MODEL : LK-D30 Firmware : Ver : SerialEmulation : epson TM-U200CR Character : CR=CR onlyFlow Control : DTR/DSRData Bits : 8 BitsParity : NoneBaud Rate : 9600 CPL : 40/33 Char/LineTwo Color : InstalledAuto Cutter : InstalledJournal : Installed3. Self Test7 Panel SwitchesPaper Feed button : Pressing the PF button momentarily will advance the paper one character line and pressing it continuously will cause a fast feed at 15 lines per SwitchA Power switch located on the lower left side of the printer is used to turn the printer section explains the different patterns signaled by the two LED indicators located on the top cover of the LK-D30 .

7 STATUSLED1 LED2 LED3 REMARKSGREENREDRED Power OffOFFOFFOFFN ormal power is not supplied to the printer Power OnFlashONONN ormal power is supplied to the printer On lineONOFFOFFN ormal error-free mode Paper lowONOFFONI nsert new paper roll Cover openONFlashOFFC lose cover Paper emptyONFlashOFFI nsert new paper roll Paper jamONOFFOFFI mpossible to recoverOFFON Test modeONONOFFI gnored Paper Low4. User EMULATION epson TM-U200 CommandHex CodeDescriptionHT<09>HHorizontal tabLF<0A>HPrint and line feedCR<0D>HCarriage ReturnDLE EOT<10>H<04>H<n>Real-time status transmissionDLE ENQ<10>H<05>H<n>Real-time request to printerESC SP<1B>H<20>H<n>Set right-side character spacingESC !

8 <1B>H<21>H<n>Set print modeESC %<1B>H<25>H<n>SSelect/cancel user-defined character setESC &<1B>H<26>HDefine user-defined charactersESC *<1B>H<2A>HSelect bit-image modeESC -<1B>H<2D> <n>Turn on/off underline modeESC 2<1B>H<32>HSelect 1/6 inch line spacingESC 3<1B>H<33>H<n>Set line spacingESC <<1B>H<3C>HReturn homeESC =<1B>H<3D>H<n>Select peripheral deviceESC ?<1B>H<3F>H<n>Cancel user-defined charactersESC @<1B>H<40>HInitialize printerESC D<1B>H<44>H<n>Set horizontal tab positionsESC E<1B>H<45>H<n>Turn on/off emphasized modeESC G<1B>H<47>H<n>Turn on/off double-strike modeESC J<1B>H<4A>H<n>Print and feed paperESC R<1B>H<52>H<n>Select an international character setESC U<1B>H<55>H<n>Turns on/off unidirectional printing modeESC a<1B>H<61>H<n>Select justificationESC c 4<1B>H<63>H<34>H<n>Select paper sensor to stop printingESC c 5<1B>H<63>H<35>H<n>Enable/disable panel buttonESC d<1B>H<64>H<n>Print and feed n linesESC p<1B>H<70>HGenerate pulseESC t<1B>H<74>H<n>Select character code tableESC

9 {<1B>H<7B>H<n>Turn on/off upside-down printing modeGS I<1D>H<49>H<n>Transmit printer IDGS a<1D>H<61>H<n>Enable/disable Automatic Status BackGS r<1D>H<72>H<n>Transmit status5. Command EMULATION CITIZEN iDP-3540 CommandHex CodeDescriptionBEL<07>HDrive pulse setting command for 1st drawerCAN<18>HClear data in bufferLF<0A>HPaper feedFF<0C>H<n>Paper feed n linesCR<0D>HPrint commandSO<0E>HSelect expanded character modeSI<0F>HSelect normal character modeDC1<11>HInitial set commandDC2<12>HInverted print modeDC3<13>HRed color print commandESC BEL<1B>H<07>H<n>1st drawer driver commandSUB<1A>H2nd drawer driver commandESC -<1B>H<2D>H<n>Select underline modeESC *<1B>H<2A>H<n>Graphic commandESC 1<1B>H<31>HSet 1/9 inch line feedESC 2<1B>H<32>H<n>Set 2/9 inch line feedESC C<1B>H<43>H<n>Set page lengthESC N<1B>H<4E>H<n>n line}

10 Skip perforation commandESC O<1B>H<4F>HCancel skip perforation commandESC P<1B>H<50>H<n>Select full-cut / partial-cutESC f<1B>H<66>HForm feedFS<1C>H1st drawer drive EMULATION STAR SP200 CommandHex CodeDescriptionBEL<07>HDiffered drive command A for peripheral unit (Default setting)CAN<18>HCancel print data in bufferLF<0A>HLine feedCR<0D>HLine feed (same as LF)SO<0E>HSelect expanded character modeSI<0F>HCancel expanded character modeFS<1C>HImmediate drive command B for peripheral unit 1DC4<14>HCancel expanded character modeESC BEL n1 n2<1B>H<07>H<n1> <n2>Adjust drive pulse width for peripheral unit(Default setting)ESC @<1B>H<40>HInitialize printerESC M<1B>H<4D>HSelect 7 x 7 (Half dots) character size (Default setting)ESC R n<1B>H<52>H<n>Select international character setESC P<1B>H<50>HSelect 9 x 7 (Half dots) character sizeESC W 1<1B>H<57>H<31>H<1B>H<57>H<1>Select expanded character modeESC W 0<1B>H<57>H<37>H<1B>H<57>H<0>Cancel expanded character modeESC a n<1B>H<61>H<n>Feed paper n lines116-1.