MODELS CL10V3 - Challenger Lifts

1 Rev. 04/07/2020 Installation, Operation & Maintenance manual Versymmetric Two Post Surface Mounted Lift MODELS : CL10V3 CL10V3 -QC (QUICK CYCLE) 10,000 LBS. CAPACITY 2500 LBS. PER ARM 2311 South Park Rd Louisville, Kentucky 40219 Web Office 800-648-5438 / 502-625-0700 Fax 502-587-1933 IMPORTANT.

2 READ THIS manual COMPLETELY BEFORE INSTALLING or OPERATING LIFT Model CL10 Installation, Operation and Maintenance Page 2 Rev 04/07/2020 GENERAL SPECIFICATIONS See Figure 1 CL10 CL10-2 CL10-3 A Column Height 11 -2 or 11 - 8 13 -2 or 13 - 8 14 -2 or 14 - 8 B Floor to Overhead

3 Switch 10 -8 1/2 or 11 - 2 1/2 12 - 8 1/2 or 13 - 2 1/2 13 - 8 1/2 or 14 - 2 1/2 C Rise Height (Screw Pads Highest Position) 74 1/8 D Cylinder Height (Full Stroke) 11 - 11 E Adjustable Overall Width 11 - 11 or 11 6 1/2" F Screw Pad Height 3 7/8 to 6 1/8 G Inside of Columns 110 or 114 1/2 Arm Reach Front/Rear ( ) Front (20 - 42 ) / Rear (37-5/8 - 60 ) Drive Thru Clearance 100 or 104 1/2" * Ceiling Height Required 12 13 - 3 or 13 - 9 14 - 3 or 14 - 9 ** Lifting Capacity (Hydraulic Pressure at Cap.)

4 10,000 lbs. (2500 lbs. Per Arm) (2750 psi) ** Lifting Time Standard: 38 Sec. (approximate) Quick Cycle: 24 Sec. (approximate) Motor 2Hp, 1Ph, 60Hz, 208/230V Optional 2Hp, 3Ph, 50/60Hz,208/230/460V 3Hp, 1Ph, 60Hz, 208/230V * Cylinder height D will extend past column height A on standard CL10 only. ** Lift capacity ratings are based on loads equally distributed on all four arms. ** Lifting and lowering speeds may vary depending on the weight of the vehicle. Fig 1a - General Specifications Fig1b - Service Bay Layout Model CL10 Installation, Operation and Maintenance Page 3 Rev 04/07/2020 WARNINGVERTICAL CLEARANCE Check the height of the area where the lift is to be installed.

5 Clearance should be calculated based on the full raised height of the lift. Failure by purchaser to provide adequate clearance could result in unsatisfactory lift performance, property damage, or personal injury. FLOORING Be certain you have the proper concrete floor to properly handle the loaded lift. Floor should be in generally good condition with no large cracks, spalling or deterioration. Minimum requirements for concrete are 4 inches minimum depth, with steel reinforcement, 3500 psi, cured for 28 days per local commercial practice.

6 Floor should be level within 3/8 inch over the installation area. No anchors should be installed within 8 inches of any crack, edge, or expansion joint. If these conditions cannot be met, a pad may be poured to accommodate the lift. Check with local building inspectors and/or permits office for any special instructions or approvals required for your installation. A qualified person should be consulted to address seismic loads and other local or state requirements.

7 Failure by purchaser to provide the recommended mounting surface could result in unsatisfactory lift performance, property damage, or personal injury. LOCATION This lift has been evaluated for indoor use only with an operating ambient temp. range of 5 40 C (41 104 F) ELECTRICAL REQUIREMENTS For lift installation and operation, it is necessary to have a dedicated circuit with circuit breaker or time delay fuse. Refer to wiring diagram for circuit sizing.

8 SAFETY NOTICES AND DECALS For your safety, and the safety of others, read and understand all of the safety notices and decals included here. READ ENTIRE manual BEFORE ASSEMBLING, INSTALLING, OPERATING, OR SERVICING THIS EQUIPMENT. PROPER MAINTENANCE AND INSPECTION IS NECESSARY FOR SAFE OPERATION. DO NOT OPERATE A DAMAGED LIFT. Safety decals similar to those shown here are found on a properly installed lift. Be sure that all safety decals have been correctly installed on the columns as described in this installation manual .

9 Verify that all authorized operators know the location of these decals and fully understand their meaning. Replace worn, faded, or damaged decals promptly. Do not attempt to raise a vehicle on the lift until the lift has been correctly installed and adjusted as described in this manual . WARNINGWARNINGM odel CL10 Installation, Operation and Maintenance Page 4 Rev 04/07/2020 RECEIVING The shipment should be thoroughly inspected as soon as it is received.

10 The signed bill of lading is acknowledgement by the carrier of receipt in good condition of shipment covered by our invoice. If any of the goods called for on this bill of lading are shorted or damaged, do not accept them until the carrier makes a notation on the freight bill of the shorted or damaged goods. Do this for your own protection. NOTIFY Challenger Lifts AT ONCE if any hidden loss or damage is discovered after receipt. IT IS DIFFICULT TO COLLECT FOR LOSS OR DAMAGE AFTER YOU HAVE GIVEN THE CARRIER A CLEAR RECEIPT.