Example: barber

MP2060 Kool-Pak Clip Mount Power Film Resistor

MP2060 Kool-Pak clip Mount Power film Resistor New clip TO-220 Style Power Resistor Designed for clip Mounting - Non-Inductive M. Value ount Up to 60 Watts continuous Power at +25 C case temperature, and above. to . Up to 60 Amps continuous current at +25 C case temperature, and below. TO-220 Style package utilizes proven Power semiconductor thermal solutions. Equivalent to UL94 V-0 flammability rating. Excellent pulse/surge performance. Non-inductive design for high speed switching, snubbers and rf applications. Operation up to +150 C case temperature. Electrically isolated case. Thermal Resistance Power Max. Current Max. Model Package Resistance Rating Rating (Amps) Voltage R JC. film (J) to Case (C). 18 Watts * 60 Arms Current Limited C/Watt 36 Watts *. Current 60 Arms Limited C/Watt TO-220. MP2060 Style 54 Watts * 60 Arms Current These products are covered by one or more Limited C/Watt patents, also patents pending. to 60 Watts * I= P/R 250 Vrms C/Watt Specifications: Derating Curve 100 * Derating Using Case Temperature (TC): Temperature Coefficient: RATED Power %.

2003-2017 Caddock Electronics, Inc. 28_IL128.0717 Sales and Applications Engineering 17271 North Umpqua Hwy. Roseburg, Oregon 97470-9422 Phone: (541) 496-0700

Tags:

  Power, Mount, Clip, Resistor, Film, Clip mount power film resistor

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Other abuse

Transcription of MP2060 Kool-Pak Clip Mount Power Film Resistor

1 MP2060 Kool-Pak clip Mount Power film Resistor New clip TO-220 Style Power Resistor Designed for clip Mounting - Non-Inductive M. Value ount Up to 60 Watts continuous Power at +25 C case temperature, and above. to . Up to 60 Amps continuous current at +25 C case temperature, and below. TO-220 Style package utilizes proven Power semiconductor thermal solutions. Equivalent to UL94 V-0 flammability rating. Excellent pulse/surge performance. Non-inductive design for high speed switching, snubbers and rf applications. Operation up to +150 C case temperature. Electrically isolated case. Thermal Resistance Power Max. Current Max. Model Package Resistance Rating Rating (Amps) Voltage R JC. film (J) to Case (C). 18 Watts * 60 Arms Current Limited C/Watt 36 Watts *. Current 60 Arms Limited C/Watt TO-220. MP2060 Style 54 Watts * 60 Arms Current These products are covered by one or more Limited C/Watt patents, also patents pending. to 60 Watts * I= P/R 250 Vrms C/Watt Specifications: Derating Curve 100 * Derating Using Case Temperature (TC): Temperature Coefficient: RATED Power %.

2 80 All Power and associated overload ratings are TC referenced to +25 C, R taken at +150 C. 60. derated based upon case temperature using the ohm and above, -20 to +80 ppm/ C. derating curve. The case temperature is mea- 40 ohm to ohm, 0 to +100 ppm/ C. sured at the center of the ceramic mounting sur- 20. face, with the part properly mounted and under ohm to ohm, 0 to +200 ppm/ C. 0 electrical load. Without a heat sink, when in free ohm to ohm, 0 to +300 ppm/ C. 25 100 150. air at +25 C, the MP2060 is rated for watts. CASE TEMPERATURE, C Operating Temperature: -55 C to +150 C. The thermal design should satisfy the following equation: Inductance: 10 nH typical in series when Case Temperature (Tc) + [Thermal Resistance (R JC) x Power applied (Watts)] 150 C, considering the full measured at the shoulder of the lead. operating temperature range of the application. Mounting Note: Mount on a smooth, clean and flat heat sink surface with a thermal interface material, such as Capacitance: <1 pf typical without heat sink.

3 Thermal grease. The entire exposed ceramic portion must be in contact with the heat sink. When using a spring clip , it is recommended that a mounting force of 8 to 30 pounds (35 to 130 N) be applied to the center of DWV: 1500 VrmsAC isolation to the mounting the package. The clip should be round or smooth in the contact area to avoid concentrating the load on a small surface or a clip in contact with the top surface. point of the plastic body of the package. Another mounting option is to use a pressure bar method which can Insulation Resistance: 10,000 Megohms, min. achieve a greater mounting force with a greater contact area. The Resistor element is electrically isolated from the For additional applications information regarding mounting and pulse handling see the Caddock Ap- mounting surface. plications Notes at or contact Applications Engineering. Momentary Overload: times rated Power for Standard Resistance Values: 5 seconds, R ( percent + ohm) max. ( ) ( ) Tolerance: 1% Standard (except as noted) Load Stability: 2000 hours at rated Power 5% 100 R less than (1 percent + ohm).

4 2% 120 . 2% 150 . Moisture Resistance: Mil-Std-202, Method 106, ( ) 200 R ( percent + ohm) max. MP2060 . 250 . ( ) 1% 300 Thermal Shock: Mil-Std-202, Method 107, 330 Cond. F, R ( percent + ohm) max. 400 . ( ). 470 Shock: 100G, Mil-Std-202, Method 213, 500 Cond. I, R ( percent + ohm) max. ( ) ( ) 560 . 750 Vibration, High Frequency: Mil-Std 202, K Method 204, Condition D, R ( percent ( ). ( ). + ohm) max.. ( ) Terminal Strength: Mil-Std-202, Method 211, DIMENSIONS IN INCHES AND (MILLIMETERS). For custom values and tolerances contact Cond. A (Pull Test) 5 lbs., R ( percent Applications Engineering + ohm) max. Ordering Information: MP2060 - - 1% Terminal Material: Solderable Model Number: Tolerance Measurement Note: Resistance measurements Resistor Value: shall be made at inch ( mm) from the Packaging Information: MP2060 resistors are packaged in plastic shipping tubes, 50 pieces Resistor body. per tube. These resistors are available in a 50 piece minimum quantity and in full tube quantity increments ( 50, 100, 150, etc.)

5 Sales and Applications Engineering ELECTRONICS, INC. 17271 North Umpqua Hwy. Roseburg, Oregon 97470-9422. e-mail: web: Phone: (541) 496-0700. For Caddock Distributors listed by country see Fax: (541) 496-0408. 2003-2017 Caddock Electronics, Inc.


Related search queries