MULTIFUNCTIONAL TRANSDUCER - …

1 1 MULTIFUNCTIONAL TRANSDUCER / CPQT13 Thank you for choosing CPQT/CPQT13 from Celsa Messger CPQT/CPQT13 is a configurable multitransducer for all electrical quantities. All areas for AC current and voltage (True RMS) is covered by one single software ConfigCPQT enables easy configuration via the CPQT/CPQT Technical data Technical data CPQT1322. Installation Installation measuring TRANSDUCER Installation software ConfigCPQT23. Configuration Connection CPQT/CPQT13 to computer Indata View data Parameters monitorized Configuration inputs TRANSDUCER input settings System connection Connection diagrams Analog Outputs Measured Binary Outputs (CPQT13 WIDE) Save / Open saved configuration Save to file Load from file 94.

2 Upgrade of firmware in CPQT/CPQT13105. Which COM-port is CPQT/CPQT13 using122 TRANSDUCERS06 MANUAL CPQT / (Un)100 400 V x Un continuously, 2 x Un 10 sMeasuring range0 500 V TRMSC onsumption (burden)Un x 1 mA / HzCurrentInput (In)1 5 AOverload2 x In continuously, 10 x In 15 s, 40 x In 1 sMeasuring range 0 10 A TRMSC onsumption (burden)< VA / phaseAux. supplyUniversal current 24 250 VDC 80 250 VACC onsumptionmax 8 WOutputsAnalogNumber5 Area +/- 20 mA+/- 10 V (option)Loadmax 750 ohm (15V)Response time< 100 msDigitalNumber2, 110 V AC/DC, 100 mACommunicationSerial RS485 General DataAccuracy class isolationSupply, in- and output are galvanically isolatedUSB1 pc for configurationTemperature range-10 to +55 C (operation)-40 to +70 C (storage)Temperature coefficient < / 10 C Test voltage4 kV AC / minInputsOvervoltage cat.

3 IIIO utputsOvervoltag cat. IIDimensions (w x h x d)150 x 70 x 73 mm DIN-railWeightca kgStandardsSS-EN 60688 SS-EN 601010 EN 61000-6-2 / -6-4 / -6-51. CPQT/CPQT13 product descriptionCPQT/CPQT13 is a configurable multitransducer for electrical quantities in a line. It is possible to optionally choose electrical quantity to the analog out-puts. 2 transistors outputs (CPQT13) can be used to energy pulses or alarm levels. The configuration is done with the software ConfigCPQT via the USB-port on Technical Data Technical data CPQT13 InputVoltageVoltage range (Un)100 400 V main voltage (nominal) Measuring range0 500 V TRMSO verload x Un continuously, 2 x Un 10 sConsumptionUn x 1 mA / HzCurrentCurrent (In)1 5 AMeasuring range 1 10 A TRMSO verload2 x In continuously, 10 x In 15 s, 40 x In 1 sConsumption < VA / phaseAux.

4 SupplyUniversal current 24 250 VDC 80 250 VACC onsumptionmax 8 VAOutputsAnalogAnalog output2 Range +/- 20 mA+/- 10 V (option)Loadmax 750 ohm (15V)Response time< 100 msGeneral DataAccuracy class isolationSupply, in- and output are galvanically isolatedUSB1 pc for configurationTemperature range-10 to +55 C (operation)-40 to +70 C (storage)Temperature coefficient < / 10 C Test voltage4 kV AC / minInputsOvervoltage cat. IIIO utputsOvervoltag cat. IIDimensions (w x h x d)70 x 132 x 137 mm DIN-railWeightca kgStandardsSS-EN 60688 - TransducersSS-EN 601010 - SafetyEN 61000-6-2 / -6-4 / -6-52. Installation measuring transducerThe TRANSDUCER is mounted in DIN-rail 35 mm for wall mounting or rack mounting in appropriate housing.

5 The installation is to be made by competentelectrician and in accordance with existing regulations. Before installation please check that the TRANSDUCER has the correct type and that the data com-ply with the order. The TRANSDUCER is connected with clamps max 2 x 2,5 mm in accordance with connection diagram, see page Installation software ConfigCPQTThe installation package consists of configuration software and USB driver..NET Framework version must be installed on the computer otherwiseConfigCPQT does not work. It is a software from Microsoft which often already is installed. If not it has to be to : and you will find.

6 NET ConfigCPQT from and unzip the Install driver for USB. is for 32-bit Windows operative and is for Install CPQT / Configuration Connection CPQT/CPQT13 to computerConnect a USB-cable between the USB-port on CPQT/CPQT13 and the computer. Use cable with contacts type A and mini File and choose COM-port and click Open Port and close the window the tab View data in the field USB Connection status the word Connected is shown with a green Indata View dataIn View data the various basic parameters of the TRANSDUCER are configurated and thepresent measuring values can be seen when the transducers is connec-ted to an object.

7 The measuring values are shown as Primary, Secondary or Raw measuring inputs on LQT can be connected to nets with a nominal main voltage between 100 and 400 V AC and a current with a nominal value 1,2 or 5 A. With the software ConfigLQT the unit can be used for all different connections in 1-phase and 3-phase Parameters monitorizedPPower P=S*cos( ) [W]QReactive power Q=S*sin( ) [var]SAppearant power S=rot(3)*Uh*Ih [VA]UVoltageICurrentFFrequencyISSystem current with sign??PFPower factor PF=P/SQFR eactive power factor QF=Q/SLF= sign(Q)*(1-|PF|)PAPhase angle4 TRANSDUCERS06 MANUAL CPQT / wire3 phase symmetric loadX--XX-----U1I1P1*3Q1*3S1*3-011 wire1 phaseX--XX-----U1I1P1Q1S1-023 wire3 phase symmetric loadX------X----PI1U12QI1U12SI1U12-033 wire3 phase symmetric loadX-------X---PI1U23QI1U23SI1U23-043 wire3 phase symmetric loadX--------X--PI1U31QI1U31SI1U31-053 wire3 phase symmetric loadX---XXXXXX-I1P1*3Q1*3S1*3-093 wire3 phase asymmetric loadX-X-XXXXXX-(I1+I3)*3/2(P1+P3)*3/2(Q1 +Q3)*3/2(S1+S3)*3/2-114 wire3 phase asymmetric loadXXXXXXXXXX(U1+U2+U3)/3(I1+I2+I3)

8 /3P1+P2+P3Q1+Q2+Q3S1+S2+S3-114 wire3 phase asymmetric loadOpen DeltaXXXXXXXXX(U1+U2+U3)/3(I1+I2+I3)/3P1 +P2+P3Q1+Q2+Q3S1+S2+ Configuration inputs - TRANSDUCER input System connection5 MANUAL CPQT / Connection diagrams CPQT6 TRANSDUCERS06 MANUAL CPQT / Connection diagrams CPQT137 MANUAL CPQT / Analog OutputsTo configurate the analog outputs select Analog OutputsThe analog outputs can freely be configurated to the required measuring quantity within the allowed measuring ranges. Select thequantity that is to be connected to the analog output using the drop-down the field Primary/Secondary the start values is to be written in the first space and in the following space the end value and the bre-akpoints if any are to be indicated.

9 Under Analog out the corresponding values of the output signal are settings transfer and save the new settings in the simulate the outputs to test for instance a panel instrument, please use the drop-down list (Fixed Output). Write the output that youdesire and click Apply CPQT / Measured quantities9 MANUAL CPQT / Binary Outputs (CPQT13 WIDE)To configuration the binary outputs, select the Binary Save / Open saved configurationThe stored parameters in the LQT can be saved to a Save to file1. Select File and Save Write filename and select Load from file1. Select File and Open Select saved configuration file (XML-dokument).

10 10 TRANSDUCERS06 MANUAL CPQT / Upgrade of firmware in CPQT / CPQT13 CPQT Firmware is upgraded with ConfigLQT. Connect the computer to the USB port of the computer. Find out which COM-port that CPQT is connected Start Config Select File and Select COM-port in the drop-down list and click Open4. Close the window with Select: File and Firmware Information about the available firmware versions that can be installed with this version of ConfigCPQT is shown. In case a new version of firmware is installed the latest version of ConfigCPQT must be Select firmware CPQT / Click Yes. The connection with CPQT will be Click Select COM-port and click Click Upgrade CPQT / The upgrade is Message that the upgrade was successful is shown.