Example: confidence

MVH-300EX MVH-200EX - Pioneer Electronics

English MVH- 300ex . MVH- 200ex . Fran ais RDS AV RECEIVER. RADIO AV RDS. RECEPTOR RDS AV. Espa ol Installation Manual Manuel d'installation Manual de instalaci n It is extremely dangerous to allow cables Important safeguards Important safety WARNING. to become wound around the steering column or shift lever. Be sure to install this product, its cables, and wiring away information Pioneer does not recommend that you install this product yourself. This product is designed for professional installation only. in such so that they will not obstruct or hinder driving. Make sure that the cables and wires will subject to the or Canadian regulations, not interfere with or become caught in WARNING We recommend that only authorized please contact the vehicle manufacturer or any of the vehicle's moving parts, Pioneer service personnel, who have Rear visibility systems (backup cameras) dealer. especially the steering wheel, shift lever, special training and experience in mobile are required in certain new vehicles sold in parking brake, sliding seat tracks, doors, Electronics , set up and install this product.

• For connecting a power amp or other devices to this product, refer to the manual for the product to be connected. • The graphical symbol placed on the product means direct current. • When the ignition switch is turned on (ACC ON), a control signal is output through the blue/white lead. Connect to an external power amp’s system remote

Tags:

  Electronic, Pioneer, 200ex, Pioneer electronics, Mvh 300ex mvh 200ex, 300ex

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Other abuse

Transcription of MVH-300EX MVH-200EX - Pioneer Electronics

1 English MVH- 300ex . MVH- 200ex . Fran ais RDS AV RECEIVER. RADIO AV RDS. RECEPTOR RDS AV. Espa ol Installation Manual Manuel d'installation Manual de instalaci n It is extremely dangerous to allow cables Important safeguards Important safety WARNING. to become wound around the steering column or shift lever. Be sure to install this product, its cables, and wiring away information Pioneer does not recommend that you install this product yourself. This product is designed for professional installation only. in such so that they will not obstruct or hinder driving. Make sure that the cables and wires will subject to the or Canadian regulations, not interfere with or become caught in WARNING We recommend that only authorized please contact the vehicle manufacturer or any of the vehicle's moving parts, Pioneer service personnel, who have Rear visibility systems (backup cameras) dealer. especially the steering wheel, shift lever, special training and experience in mobile are required in certain new vehicles sold in parking brake, sliding seat tracks, doors, Electronics , set up and install this product.

2 The and Canada. regulations If your vehicle has a compliant backup or any of the vehicle's controls. NEVER SERVICE THIS PRODUCT YOURSELF. began according to a two year phase-in on camera that displays the backup view Do not route wires where they will be Installing or servicing this product and its May 1, 2016, and both the and Canada through the factory receiver, do not use exposed to high temperatures. If the connecting cables may expose you to the require that all such vehicles manufactured the Pioneer receiver unless it is connected insulation heats up, wires may become risk of electric shock or other hazards, and on or after May 1, 2018 have rear visibility to and displays the same view as the damaged, resulting in a short circuit or can cause damage to this product that is systems. Owners of vehicles equipped factory backup camera. Connection to the malfunction and permanent damage to not covered by warranty. with compliant rear visibility systems factory backup camera will require an the product.

3 Should not install or use this product in adaptor, sold separately. Not all vehicles Do not shorten any leads. If you do, the a way that alters or disables that may be able to connect. Please check with Precautions before protection circuit (fuse holder, fuse system's compliance with applicable resistor or filter, etc.) may fail to work regulations. If you are unsure whether a qualified professional installer for installation options specific to your vehicle. connecting the system properly. your vehicle has a rear visibility system Never feed power to other electronic WARNING products by cutting the insulation of the power supply lead of this product and Do not take any steps to tamper with or tapping into the lead. The current disable the parking brake interlock system capacity of the lead will be exceeded, Connection which is in place for your protection. Tampering with or disabling the parking brake interlock system could result in causing overheating.

4 Serious injury or death. Before installing this product, pull over, park your vehicle in a Precautions safe location and apply the parking brake CAUTION product before making the necessary Secure all wiring with cable clamps or adjustments. electrical tape. Do not allow any bare Use this unit with a 12-volt battery and Your new product and this Do not install this product where it may wiring to remain exposed. negative grounding only. Failure to do so (i) obstruct the driver's vision, Do not directly connect the yellow lead of may result in a fire or malfunction. manual (ii) impair the performance of any of the this product to the vehicle battery. If the To avoid shorts in the electrical system, vehicle's operating systems of safety lead is directly connected to the battery, be sure to disconnect the ( ) battery Do not operate this product, any features, including airbags, hazard lamp engine vibration may eventually cause cable before installation.

5 Applications, or the rear view camera buttons, or the insulation to fail at the point where option (if purchased) if doing so will (iii) impair the driver's ability to safely the wire passes from the passenger divert your attention in any way from the operate the vehicle. compartment into the engine To prevent damage safe operation of your vehicle. Always In some cases, it may not be possible to compartment. If the yellow lead's observe safe driving rules and follow all install this product because of the vehicle insulation tears as a result of contact with WARNING. existing traffic regulations. If you type or the shape of the vehicle interior. metal parts, short-circuiting can occur, When speaker output is used by 4. experience difficulty in operating this resulting in considerable danger. channels , use speakers over 50 W. 2 En (Maximum input power) and between 4. to 8 (impedance value). Do not use 1 Rear panel Power cord to 3 speakers for this unit.

6 When rear speaker output is used by 2 . of subwoofer, use speakers over 70 W. (Maximum input power). *Please refer to connection for a ACC position No ACC position connection method. English To avoid short-circuiting, cover the The black cable is ground. When disconnected lead with insulating tape. It installing this unit or power amp (sold is especially important to insulate all separately), make sure to connect the unused speaker leads, which if left ground wire first. Ensure that the ground uncovered may cause a short circuit. wire is properly connected to metal parts For connecting a power amp or other of the car's body. The ground wire of the devices to this product, refer to the power amp and the one of this unit or Microphone 3 m (9 ft. 10-1/8 in.). manual for the product to be connected. any other device must be connected to This product The graphical symbol placed on the car separately with different screws. If Antenna jack the product means direct current.

7 The screw for the ground wire loosens or Wired remote input falls out, it could result in fire generation Connect to steering wheel control of smoke or malfunction. Notice for the blue/ interface of your vehicle. For more details, consult your dealer. To power supply Ground wire POWER AMP white lead Power supply Power cord Fuse (10 A) Yellow When the ignition switch is turned on Front output To terminal supplied with power (ACC ON), a control signal is output Rear output regardless of ignition switch position. through the blue/white lead. Connect to Subwoofer output Red an external power amp's system remote To electric terminal controlled by control terminal, the auto-antenna relay ignition switch (12 V DC) ON/OFF. control terminal, or the antenna booster Orange/white power control terminal (max. 300 mA 12 To lighting switch terminal. Other devices Metal parts of car's V DC). The control signal is output Black (ground). (Another electronic body through the blue/white lead, even if the To vehicle (metal) body.)

8 Device in the car). audio source is switched off. Violet/white *1 Non supplied for this unit Of the two lead wires connected to the When replacing the fuse, be sure to only back lamp, connect the one in which use a fuse of the rating prescribed on this the voltage changes when the gear shift product. is in the REVERSE (R) position. This This product cannot be installed in a connection enables the unit to sense vehicle without ACC (accessory) position whether the car is moving forward or on the ignition switch. backward. Blue/white Connect to system control terminal of the power amp (max. 300 mA 12 V DC). Light green Used to detect the ON/OFF status of the parking brake. This lead must be En 3. connected to the power supply side of Gray/black the parking brake switch. Green iPod /iPhone and Power supply side Green/black smartphone Parking brake switch Violet Ground side Violet/black NOTE. Subwoofer (4 ). When using a subwoofer of 2 , be sure For details on how to connect an external Speaker leads to connect the subwoofer to the violet device using a separately sold cable, refer and violet/black leads of this unit.

9 Do to the manual for the cable. not connect anything to the green and green/black leads. iPod/iPhone with Not used. Subwoofer (4 ) 2 Lightning connector NOTES. When a subwoofer is connected to this product instead of a rear speaker, change With internal amp Connecting via the USB port the rear output setting in the initial setting. The subwoofer output of this Important product is monaural. Front speaker and Rear speaker are output For details, refer to the Operation Manual. from the speaker leads when this With a two-speaker system, do not connection is in use. connect anything to the speaker leads that are not connected to speakers. Perform these connections when using a subwoofer without the optional amplifier. Power amp (sold separately) System remote control USB port Connect to Blue/white cable. USB extension cable m (4 ft. 11 in.). Power amp (sold separately) USB interface cable for iPod/iPhone (CD- Connect with RCA cable (sold IU52) (sold separately).)

10 Without internal amp separately) iPhone with Lightning connector Important To Rear output The speaker leads are not used when this Rear speaker connection is in use. To Front output Front speaker To Subwoofer output To power supply Subwoofer Power cord Left NOTES. Right You can change the RCA output of the Front speaker subwoofer depending on your Rear speaker subwoofer system. White The subwoofer output of this product is White/black monaural. Gray 4 En USB Type-C cable (Type USB A - USB C). iPhone with 30-pin (supplied with CD-CU50 (sold External video connector separately)). Smartphone component and the NOTE. display The length of Type USB A - micro USB B. Connecting via the USB port cable cannot exceed 2 m (6 ft. 6 in.) and English Type USB A - USB C cannot exceed 4 m (13. ft. 1 in.) according to the USB cable standard. When using a cable other than the above conditions, the main unit function may not operate properly. Camera Rear view camera (ND-BC8) (sold About rear view camera separately).


Related search queries