Example: air traffic controller

NeoSwitch Passive Infrared (PIR) 347V Dual Relay …

Installation Instructions NeoSwitch Passive Infrared (PIR) 347V Model Model #. #. ONW-P-1001-D347-W. ONW-P-1001-D347-V. Dual Relay Occupancy Sensing Wall Switch Model Model Model #. #. #. ONW-P-1001-D347-LA. ONW-P-1001-D347-G. ONW-P-1001-D347-B. P/N 9850-000338-01. (Ground Required). General Information EcoMeter Operation Action EcoMeter Benefit Location Read all instructions on both sides of this Install in accordance with ALL local codes Load 1 Load 2 EcoMeter LED A person enters the space and one of 50% Increased awareness of energy savings When installing the ONW-P-1001-D347 in a new junction box, choose the switch location carefully to provide the loads is activated sheet first For indoor use only optimum coverage of the occupied area.

Eaton’s Cooper Controls Business 203 Cooper Circle Peachtree City, Georgia 30269 Printed in Malaysia www.coopercontrol.com Adjustments should …

Tags:

  Control

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Other abuse

Transcription of NeoSwitch Passive Infrared (PIR) 347V Dual Relay …

1 Installation Instructions NeoSwitch Passive Infrared (PIR) 347V Model Model #. #. ONW-P-1001-D347-W. ONW-P-1001-D347-V. Dual Relay Occupancy Sensing Wall Switch Model Model Model #. #. #. ONW-P-1001-D347-LA. ONW-P-1001-D347-G. ONW-P-1001-D347-B. P/N 9850-000338-01. (Ground Required). General Information EcoMeter Operation Action EcoMeter Benefit Location Read all instructions on both sides of this Install in accordance with ALL local codes Load 1 Load 2 EcoMeter LED A person enters the space and one of 50% Increased awareness of energy savings When installing the ONW-P-1001-D347 in a new junction box, choose the switch location carefully to provide the loads is activated sheet first For indoor use only optimum coverage of the occupied area.

2 When replacing an existing Wall Switch, bear in mind that there must be a OFF OFF 100%. Both loads are on OFF clear Line-of-sight between the sensor and the area to be covered. Avoid pointing the ONW-P-1001-D347 directly ON OFF 50% into the hallway where it may detect passers-by. Specifications The area is vacated and the lights turn 100%. Increased awareness of energy savings;. OFF ON 50% OFF automatically Acts as a night light locator Technology: Passive Infrared (PIR) Light Level Sensing: 0 to 200 foot-candles Electrical Ratings (Per Relay ): Operating Environment: ON ON OFF Increased awareness of energy 347 VAC: Temperature: 32 F 104 F (0 C 40 C) A person turns the lights OFF.

3 100%. savings and reminds individuals to take control of their lighting for Installation Incandescent/Tungsten Max. load: amps, Relative Humidity: 20% to 90% Non-condensing manually upon exiting an area additional savings; Acts as a night The ONW-P-1001-D347 can be installed in any standard single 1500W, 50/60 Hz Housing: Durable, injection molded housing. light locator gang box. It may be installed in the same manner as an ordinary Wall Switch. Fluorescent/Ballast Max. load: amps, Polycarbonate resin complies with UL94VO.

4 If the daylighting function is activated Increased awareness of energy 1500W, 50/60 Hz Size: for one of the two loads and there is savings; Lets persons know that the Wire the ONW-P-1001-D347 as described in the wiring section. 50%. Ballast Compatibility: Compatible with magnetic and Mounting Plate/Strap Dimensions: sufficient daylight in the space, the daylight sensor is holding the lights unit will hold that load OFF OFF; Acts as a night light locator Mount the ONW-P-1001-D347 in the junction box. electronic ballasts H x W ( mm x 44 mm).

5 No Minimum Load Requirement Product Housing Dimensions: H x . If the daylighting function is activated Increased awareness of energy Time Delays: Self-Adjusting, 15 seconds/test (10 min W x D ( mm x mm x mm) for both loads and there is sufficient savings; Lets persons know that the 100%. Auto), Selectable 5, 15, 30 minutes LED Indicators: Red LED indicates PIR detection; Green daylight in the space, the unit will hold daylight sensor is holding the lights that loads OFF OFF; Acts as a night light locator Coverage: Major motion 1000 sq.

6 Ft. LED acts as EcoMeter or night light locator. Minor motion 300 sq. ft. Description Coverage Wiring The ONW-P-1001-D347 Occupancy Sensing Wall Switch is a Passive Infrared (PIR) motion sensing lighting control The ONW-P-1001-D347 is designed for offices up to 300 square feet. CAUTION: Before installing or performing any service on a Greengate system, the power MUST be turned and conventional Wall Switch all-in-one, used for energy savings and convenience. OFF at the branch circuit breaker. According to NEC 240-83(d), if the branch circuit breaker is used as the main switch for a fluorescent lighting circuit, the circuit breaker should be marked SWD.

7 All installations PIR Technology , should be in compliance with the National Electric Code and all state and local codes. 36. The sensor's segmented lens divides the field of view into sensor zones, and detects the changes in temperature NOTE REGARDING COMPACT FLUORESCENT LAMPS: The life of some compact fluorescent lamps (CFLs) is , that are created when a person, or part of a person as small as a hand, passes into or out of a sensor zone. 20 shortened by frequent automatic or manual switching. Check with CFL and ballast manufacturer to determine the The ONW-P-1001-D347 allows the control of two separate loads with one occupancy sensor switch.

8 Effects of cycling. Energy Saver Mode Either or both loads may be configured to turn ON manually. The default setting for the Minor Motion, IR. second load is Manual ON. This ensures the Wall Switch only activates one load. If both loads are on when the 1. Make sure power is turned OFF at the branch circuit breaker. sensor times out, only the primary load will be activated. If the lights were shut OFF manually, the unit will activate Major Motion, IR 2. Wire units as shown in wiring diagrams per applicable voltage requirements.

9 The primary load only. 3. Mount unit to Wall Box. In Automatic ON Mode, the lights turn ON automatically when a person enters the room. In Manual ON Mode, the , 4. Turn power back ON at the branch circuit breaker and wait 2 minutes for the unit to stabilize. lights are turned ON by pressing the universally recognized light icon Pushbutton. In either mode, the lights stay ON 8 5. Make necessary adjustments. (See Checkout and Adjustments section). as long as the sensor detects motion in the room. When the room is vacated, the lights turn OFF automatically after 6.

10 Install Wall Switch plate. a preset Time Delay interval. The sensor includes self-adaptive technology that continually adjusts to conditions by adjusting sensitivity and Wiring Diagram 1: Time Delay in Real-time. By adjusting sensitivity and Time Delay automatically, the sensor is maximizing the potential 347 VAC dual level single circuit wiring diagram energy savings that are available in the particular application. The EcoMeter provides a visual indicator of energy usage, increasing end user awareness and reminding individuals to take control of their lighting to maximize energy savings.


Related search queries