Note: the section properties for square and rectangular ...

1 Note: the section properties for square and rectangular tube are calculated exclusive of the corner radii. Disclaimer: the section properties in this table were calculated using recognized engineering principles and are for general information only. While believed to be accurate, this information should not be used or relied upon for any specific application without competent professional examination and verification of its accuracy, suitability or applicability by a licensed professional engineer, designer or architect. The publication of the information herein is not intended as a representation of warranty on the part of Allied Tube & Conduit.

2 Anyone making use of this information assumes all liability arising from such use. Nov. 2001 Yield Tensile Outside Decimal Nominal Strength StrengthSection Moment Radius of Shape Diameter Gauge Gauge Lbs/Foot(psi) (psi) Modulus of Inertia Gyration Area Round 22 45,000 48,000 20 45,000 48,000 19 45,000 48,000 18 45,000 48,000 17 45,000 48.

3 000 16 45,000 48,000 22 45,000 48,000 20 45,000 48,000 19 45,000 48,000 18 45,000 48,000 17 45,000 48,000 16 45,000 48,000 22 45,000 48,000 20 45,000 48,000 19 45,000 48,000 18 45,000 48.

4 000 17 45,000 48,000 16 45,000 48,000 22 45,000 48,000 20 45,000 48,000 19 45,000 48,000 18 45,000 48,000 17 45,000 48,000 16 45,000 48,000 15 50,000 55,000 22 45,000 48,000 20 45,000 48.

5 000 19 45,000 48,000 18 45,000 48,000 17 45,000 48,000 16 45,000 48,000 15 50,000 55,000 14 50,000 55,000 22 45,000 48,000 20 45,000 48,000 19 45,000 48,000 18 45,000 48,000 17 45,000 48.

6 000 16 45,000 48,000 15 50,000 55,000 22 45,000 48,000 20 45,000 48,000 19 45,000 48,000 18 45,000 48,000 Note: the section properties for square and rectangular tube are calculated exclusive of the corner radii.

7 Disclaimer: the section properties in this table were calculated using recognized engineering principles and are for general information only. While believed to be accurate, this information should not be used or relied upon for any specific application without competent professional examination and verification of its accuracy, suitability or applicability by a licensed professional engineer, designer or architect. The publication of the information herein is not intended as a representation of warranty on the part of Allied Tube & Conduit. Anyone making use of this information assumes all liability arising from such use.

8 Nov. 2001 Yield Tensile Outside Decimal Nominal Strength StrengthSection Moment Radius of Shape Diameter Gauge Gauge Lbs/Foot(psi) (psi) Modulus of Inertia Gyration Area Round 17 45,000 48,000 16 45,000 48,000 15 50,000 55,000 22 45,000 48,000 20 45,000 48.

9 000 19 45,000 48,000 18 45,000 48,000 17 45,000 48,000 16 45,000 48,000 15 50,000 55,000 14 50,000 55,000 22 45,000 48,000 20 45,000 48,000 19 45,000 48,000 18 45,000 48,000 17 45,000 48.

10 000 16 45,000 48,000 15 50,000 55,000 14 50,000 55,000