OI L SEAL S CATALOG

1 Durus Seals are a product of Baart Industrial Group LLC (Baart). Baart has tried to ensure the accuracy of the information contained in this document, Baart accepts no responsibility for inaccuracies in, or changes to, such information. Baart reserves the right to change all data indicated in this CATALOG without notice. Baart Industrial Group 2016. All rights (DRS-16)DISTRIBUTED BY:PRODUCT OF OIL SEALS SEALS2 DRS-16 Durus Oil What do you want to do? Select a seal Go to Page 09 Check Compound Compatibility Go to Page 12 Review seal Profiles Go to Page 19 Install a Product Go to Page 22 Troubleshooting Go to Page 24 View Product Listings Go to Page 26 Find an Interchange Go to Page 66 Copyright 2016, Baart Industrial Group.

2 All rights reserved. The contents of this CATALOG are subject to change without notice or Industrial Group (Baart) has tried to ensure that the information contained in this CATALOG is accurate. Baart makes no warranty or guarantee concerning the accuracy or reliability of the content. Assessing accuracy and reliability of information is the responsibility of the user. Baart shall not be liable for errors contained herein or for any damages in connection with the use of the information contained herein. 2 Table of ContentsFeatures Durus Oil Seals.

3 4 Safety Warnings .. 6 Nomenclature Oil seal Numbering System .. 6 Metric seal Part Numbers .. 6 Inch-Dimension seal Part Numbers .. 6 General Rules .. 7 Example Part Numbers .. 7 Additional Characters .. 7 Oil seal Components Components Part List .. 8 seal Selection Shaft Speeds .. 9 Operating Temperature .. 9 Pressure .. 9 Shaft Hardness .. 9 Shaft Surface Finish .. 9 Alignment .. 9 seal Size .. 9 Dynamic Runout .. 9 Lubricant .. 9 Material Properties Nitrile Properties .. 10 Polyacrylate Properties.

4 10 Silicone Properties .. 10 Fluorocarbon (Viton ) Properties .. 10 Carbon Steel Properties .. 10 Stainless Steel Properties .. 10 Compound Performance Thermal Range .. 11 Heat and Cold Resistance .. 11 Oil and Water Resistance .. 11 Acid and Alkali Resistance .. 11 Wear and Ozone Resistance .. 11 Compound Compatibility Fluid Compatibility Chart .. 12 seal Tolerances Actual Dimensions vs. Press Fits .. 13 Width Dimension Tolerances .. 13 OD Press Fit Tolerances .. 13 Shaft Specifications Shaft Hardness .. 14 Shaft Finish.

5 14 Shaft Dimension Tolerances .. 14 Shaft Misalignment .. 14 Dynamic Runout .. 15 Maximum Shaft Speeds .. 15 Housing Specifications Housing Material and Hardness .. 16 Housing Finish .. 16 Inch-Dimension and Metric Bores .. 16 Chamfers Housing Chamfer Specifications .. 17 Shaft Chamfer Specifications .. 17 Lubrication seal Lubrication .. 18 Lubricating a Double Lip seal .. 18 Lubricating a Redundant seal .. 18 Standard seal Styles Standard seal Designs .. 19 Lip Types Standard Lip Design .. 20 Type S .. 20 Type V .. 20 Type K.

6 20 Type D .. 20 Other Lip Types .. 20 Case Types Type A .. 21 Type B .. 21 Type C .. 21 Type F .. 21 Type BZ .. 21 Other Case Types .. 21 Viton is a registered trademark of DuPont Performance Elastomers LLC. All rights Oil seal Installation Installation Instructions .. 22 Durusleeve Installation Installation Instructions .. 23 Troubleshooting and seal Analysis Inspection .. 24 Troubleshooting Table .. 24 seal Storage and Handling Storing Oil Seals .. 25 Shelf Life .. 25 Product Listings Metric Products .. 26 End Caps.

7 26 Metric seal List .. 27 Inch-Dimension Products .. 44 Truck Seals .. 44 Inch-Dimension seal List .. 45 Durusleeve Wear Sleeves .. 58 Converting Millimeters to Inches .. 58 Wear Sleeve List .. 59 Select seal System The Select seal System ..66 Select seal Features ..66 Product Interchange Product Interchange Information ..66 Interchange By Part Number ..67 SKF (CR) Interchange ..102 TCM Interchange ..108 Timken (National) Interchange ..140 Charts Thermal Conversion Chart ..154 Equivalent Measurements Chart.

8 155 Page for Additional Notes ..1564 Features OIL SEALS5 ElastomersWith a variety of sealing compounds to select from, getting what you need for your application is easy with Durus. Case MaterialsStandard seals are reinforced with AISI 1008-1010 carbon steel cases. The strong case offers protection against deformation and damage during seals are manufactured in accordance to relevant standards. Shaft and bore sizes adhere to RMA or DIN standards for precise and effective SystemAn intelligent numbering system offers valuable information.

9 Part numbers are in dimensional order making Durus seals easy to stock and locate. Superior PackagingBecause Durus seals are individually bagged in durable, air-tight plastic, you can expect a longer shelf life than other packaging methods. DurusStanding Durus, we manufacture durable seals for mechanical systems. With cutting-edge engineering and manufacturing processes,we create a seal you can depend on. Check out the features below:Lubricants stay put, contaminants Warnings Avoid touching melted lip compounds as they can cause skin irritation.

10 Inhaling melted lip compounds will cause lung irritation. Make sure all machinery has been shut off and locked out before removing or replacing seals. Lubricants and machinery may be very hot. Ensure that the system is cool before removing or replacing seal Numbering System Durus part numbers are derived from the dimensions and features of the seal . All part numbers include some dimensional information as well as case, lip, and material designations. Metric seal Part Numbers Metric seal part numbers list the three seal dimensions, separated by two X's.