Example: barber

OLYMPUS INSTRUCTIONS

INSTRUCTIONSOLYMPUSP lease read this instruction manual carefully before usingthe camera, so that you may be sure of taking correctlyexposed, properly focused and beautifully composed pic-tures every time you use your OM-2S PROGRAM. Wesincerely wish that your OM-2S PROGRAM will become asource of unending satisfaction for : All the components of the OLYMPUS OM-2S PROGRAM are carefully designed and their produc-tion and assembly is strictly controlled to enhance the unmatched performance of the system. Ifany interchangeable lenses, flashes, or accessories other than OLYMPUS products are used, Olympuscannot be responsible for poor results or damage of the OM-2S orderAutomaticoperationTwo-step operationAttentionPress lightlyLamp onLamp blinkingContinuous soundReferenceA-1 TABLE OF CONTENTS< Preparations before Taking Pictures > Mounting the Lens.

by TTL direct "off-the-film" light measuring with aperture-preferred elec-tronic shutter (center-weighted average light measurement); exposure con-trol range: about 1 min. ~ 1/1000 sec.; light measuring range: approx.-5EV~ 18EV (ISO/ASA 100, 50mm F1.4, normal temperature and humidity); Flash control: Automatic flash exposure at 1/60 sec. or slower

Tags:

  Measuring, Light, Film, Light measuring, The film

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Other abuse

Transcription of OLYMPUS INSTRUCTIONS

1 INSTRUCTIONSOLYMPUSP lease read this instruction manual carefully before usingthe camera, so that you may be sure of taking correctlyexposed, properly focused and beautifully composed pic-tures every time you use your OM-2S PROGRAM. Wesincerely wish that your OM-2S PROGRAM will become asource of unending satisfaction for : All the components of the OLYMPUS OM-2S PROGRAM are carefully designed and their produc-tion and assembly is strictly controlled to enhance the unmatched performance of the system. Ifany interchangeable lenses, flashes, or accessories other than OLYMPUS products are used, Olympuscannot be responsible for poor results or damage of the OM-2S orderAutomaticoperationTwo-step operationAttentionPress lightlyLamp onLamp blinkingContinuous soundReferenceA-1 TABLE OF CONTENTS< Preparations before Taking Pictures > Mounting the Lens.

2 4 Detaching the Lens ..5 Inserting the Batteries ..6 Checking the Batteries ..7 Loading the film ..8 Setting the Exposure Counter to "1" ..11 Setting the ISO film Speed ..12< Basic Shooting Mode > Programmed Exposure on TTL Direct"OTF" light Metering ..14 Rewinding the film ..17 TTL Direct "OTF" light Metering ..19 What to Do when OverexposureWarning Appears? ..22 What to Do when Shutter Speedis too Slow? ..22< Sophisticated Shooting Mode > How to Use the MANUAL/SPOT ..24 Exposure Compensation ..27 How to Shoot when the Batteriesare Exhausted ..27< Other Operations > The Use of the Self-Timer ..30 Using the Viewfinder Illuminator.

3 31 How to Turn off the Beeper ..32 Attaching the Grip ..32< OM System > Changing the Focusing Screen .. 35 Changing the Camera Back .. 36 Attaching the Electronic Flash .. 37 Attaching the Motor Drive or Winder ..39 Handling Care ..41 Storage Care ..42 Battery Precaution ..42 Description of Controls ..43 Specifications ..47A-2OM-2 SPROGRAM< Preparations before Taking Pictures >A-3 Mounting the LensRemove the body and rear lens the front lens cap. (Press in the mounttabs on the edges of the lens cap parallel with" OLYMPUS ").21A-4 Detaching the Lens3 Align the red dots and rotate the lens clock-wise until it the lens release button and turn the the Batteries21 Remove the battery battery surfaces clean.

4 Make sure that +signs are facing ( LR44) 2A-6 Checking the Batteries2 Press the mode selector lever to the "BAT-TERY CHECK" audible and visual signals will tell you thatthe battery voltage is these signals are emitted intermittently, it meansthat the batteries are almost worn out. Replacethem with new ones as soon as possible.* Make sure that the shutter speed ring is not setat 1/60 sec. or B (in red).* * Be sure to make battery check after the Film12 Place the film cartridge in the film up on the rewind knob to open the cam-era off the top of thefilm box and insert it into thememo holder.

5 It will remindyou which film you are load filmin the 4 Insert the film leader into the take-up the film 6 Continue to advance the film till sprockets arecaught on both edges of the up the slack by turning the rewind the Exposure Counter to "1"7 Close the camera back until it clicks into the camera toward light and take twoblind the ISO film Speed12 Lift up the outer collar and rotate until theISO speed appears in the the exposure line with the indexA-12OM-2 SPROGRAM< Basic Shooting Mode >A-13 Programmed Exposure on TTL Direct "OTF" light Metering (Center-Weighted Averaging Method)1 2 Set the mode selector lever to the "PRO-GRAM" the lens to its minimum 4 Press the shutter release slightly to turn on theviewfiner.

6 (A built-in battery conserver turns off the view-finder display after 90 sec.)Turn the focus ring in either direction untilthe subject is can focus using any of the focusing aids:Split-image rangefinder Microprism collarSurronding ground the shutter release to take the the FilmWhen the exposure counter indicates the endof your roll of filmPush the "R" out the rewind crank and wind it untilthe film tension is the camera back by pulling up on therewind knob and remove the Direct "OTF" light Metering (Center-Weighted Averaging Method)12 Set the mode selector lever to the "AUTO" the the shutter release slightly to turn on theviewfinder.

7 (A built-in battery conserver turns off the view-finder display after 90 sec.)Turn the focus ring in either direction untilthe subject is 6 Press the shutter release to take the to Do when Overexposure Warning Appears? What to Do when Shutter Speed is too Slow?Turn the aperturering to the higher F-numbers until the shut-ter speed is in the ac-ceptable the aperturering to the lower F-numbers. This will speedup the shutter speed < Sophisticated Shooting Mode >A-23 How to Use the MANUAL/SPOT12 Set the mode selector lever to the "MANUALSPOT" the microprism area with the area youwant to spot metering range is outlined bythe outer edge of the 4 Set the bar graph tip to the fixedpoint between the arrows by adjust-ing the aperture and/or shutter the composition as you MANUAL/SPOT mode.

8 Frame your subjectafter setting the shutter release to take the 6A-26 Exposure Compensation How to Shoot when the Batteries are ExhaustedThe exposure compensation dialprovides 2 stops adjustment in 1/3stop increments, " " indicator lightswhen an exposure compensation is set.(After use, be sure to return the dial tothe normal setting.)While pressing the "B" Lock button, rotatethe shutter ring to the red "60" 3 Mechanical shutter speed of 1/60 the shutter release to take the < Other Operations>A-29 The Use of the Self-Timer12 With the camera facing you, lift up on theself-timer lever, and turn it counter-clockwise (asindicated).

9 Press the shutter release to start the self-timer. The shutter will fire in 12 seconds. (Afteruse, be sure to return the lever to the normal posi-tion.)A-30 Using the Viewfinder Illuminator1 2 Push the button if the viewfinder display istoo dark to illuminator is limited to 10 sec. or untilyou take the photograph, whichever comes to Turn Off the BeeperAttaching the GripIf you want to turn off the audible signal, liftup the lever and push it clockwise around towardsthe Grip 1 (optional)This grip pro-vides a firm handhold for the Focusing Screen1 2 Push up on the release catch, and the focusingscreen and its frame will remove the focusing screen usingthe tools place the new focusing screen in the frame,and push the frame up until it the Camera Back1 2 Pull up on the rewindcrank to open the camera back 4 (optional)B-39A-36 Attaching the Electronic Flash1 2 Electronic Flash T45 TTL Auto Cord T2 ( )

10 B-31 Connect the camera's TTLAuto Cord Socket to the base ofthe T45 with TTL Auto Cord T2( , ).A-371 2 Electronic Flash T32 and T20 Slide the flash into the hot the flash mount with the knurled the Motor Drive or Winder12 Motor Drive 2 / Ni-Cd Control Pack 2 Remove the motordrive the fastening screw of the Motor Driveor Winder into the tripod socket of the camera. Finger tighten 2A-40 Handling CareTake care in handling the not apply excessive Care Battery PrecautionGuard against high temperature and magnetic case of malfunction.


Related search queries