Transcription of OMCS Requirements - Road Tunnel And Underpass Lighting
1 ROADS AND MARITIME SERVICES (RMS) RMS SPECIFICATION D&C TS918 OMCS Requirements - road Tunnel AND Underpass Lighting NOTICE This document is a Roads and Maritime Services D&C Specification. It has been developed for use with Design & Construct roadworks and bridgeworks contracts let by Roads and Maritime Services. It is not suitable for any other purpose and must not be used for any other purpose or in any other context. Copyright in this document belongs to Roads and Maritime Services. REVISION REGISTER Ed/Rev Number Clause Number Description of Revision Authorised By Date Ed 1/Rev 0 First issue. DCS Edition 1 / Revision 0 ROADS AND MARITIME SERVICES August 2017 SPECIFICATION D&C TS918 OMCS Requirements - road Tunnel AND Underpass Lighting Copyright Roads and Maritime Services IC -DC-TS918 VERSION FOR: DATE: Edition 1 / Revision 0 ROADS AND MARITIME SERVICES August 2017 OMCS Requirements - road Tunnel and Underpass Lighting D&C TS918 CONTENTS CLAUSE PAGE FOREWORD.
2 II RMS Copyright and Use of this Document .. ii Base Specification .. ii 1 GENERAL .. 1 Scope .. 1 Related Specifications .. 1 Structure of the Specification .. 2 Definitions and Acronyms .. 3 2 DESIGN .. 4 General .. 4 Tunnel Lighting .. 4 Underpass Lighting .. 5 Mains Failure Lighting .. 5 Emergency Lighting /Signage in Tunnel .. 6 Lighting for Services Galleries and Emergency Egress Passages .. 6 Illuminated Tunnel Signs .. 6 Lighting Photometer Control System for Tunnel .. 6 Design Compliance .. 7 Alternative Design and Technology .. 8 3 EQUIPMENT AND COMPONENTS .. 8 General .. 8 Luminaires .. 9 Control Gear .. 10 Illuminated Tunnel Signs .. 10 Photometers .. 10 Equipment List .. 11 Certificate of Suitability.
3 11 4 INSTALLATION .. 11 General .. 11 Cableway Identification .. 11 Cable Identification .. 12 Luminaires .. 12 5 INSPECTION AND TESTING .. 13 General .. 13 Inspection by RMS Representative .. 13 Production Tests .. 13 Witness Point and Hold Point .. 14 6 COMMISSIONING .. 14 General .. 14 Verification of Lighting Performance .. 15 Commissioning Report .. 15 Inspection by RMS Representative .. 15 Testing with the OMCS .. 15 Witness Point and Hold Point .. 16 Ed 1 / Rev 0 i D&C TS918 OMCS Requirements - road Tunnel and Underpass Lighting 7 SPARE PARTS .. 16 ANNEXURES TS918/A AND TS918/B (NOT USED) .. 17 ANNEXURE TS918/C SCHEDULES OF HOLD POINTS AND IDENTIFIED RECORDS .. 17 C1 Schedule of Hold Points .. 17 C2 Schedule of Identified 17 ANNEXURE TS918/D PLANNING DOCUMENTS.
4 18 ANNEXURES TS918/E TO TS918/L (NOT USED) .. 18 ANNEXURE TS918/M REFERENCED DOCUMENTS .. 19 LAST PAGE OF THIS DOCUMENT IS .. 20 FOREWORD RMS COPYRIGHT AND USE OF THIS DOCUMENT Copyright in this document belongs to Roads and Maritime Services. When this document forms part of a deed This document should be read with all the documents forming the Project Deed. When this document does not form part of a deed This copy is not a controlled document. Observe the Notice that appears on the first page of the copy controlled by RMS. A full copy of the latest version of the document is available on the RMS Internet website: BASE SPECIFICATION This document is based on Specification RMS R 158 Edition 1 Revision 3. ii Ed 1 / Rev 0 (RMS COPYRIGHT AND USE OF THIS DOCUMENT - Refer to the Foreword after the Table of Contents) RMS SPECIFICATION D&C TS918 OMCS Requirements - road Tunnel AND Underpass Lighting 1 GENERAL SCOPE This Specification sets out the Requirements of the design, supply, installation and commissioning of road Tunnel and Underpass Lighting (RTUL), to provide conditions in the Tunnel or Underpass that are safe for the full range of operational Requirements , including during emergencies.
5 This Specification does not cover the Requirements of approach road Lighting . RELATED SPECIFICATIONS This Specification is a Level 2 document which forms part of the suite of RMS specification documents for the Operations Management and Control System (OMCS) for Motorways (see figure below). Other documents within the suite are: Level 1 D&C TS901 OMCS Overview and General Requirements ; Level 2 D&C TS911 OMCS Requirements - Motorway Control Centre ; D&C TS912 OMCS Requirements - Traffic Management and Control System ; D&C TS913 OMCS Requirements - Plant Management and Control System ; D&C TS914 OMCS Requirements - Electrical Power Supply and Distribution System ; D&C TS915 OMCS Requirements - Motorway Network Communications System ; D&C TS916 OMCS Requirements - Electronic Toll Collection System ; D&C TS917 OMCS Requirements - C2C Interface for Motorways ; Level 3 D&C TS931 Tunnel and Underpass Main Switchboard, Distribution Boards and Control Panels ; D&C TS933 Tunnel Backlit Static Signage.
6 Ed 1 / Rev 0 1 (RMS COPYRIGHT AND USE OF THIS DOCUMENT - Refer to the Foreword after the Table of Contents) D&C TS918 OMCS Requirements - road Tunnel and Underpass Lighting STRUCTURE OF THE SPECIFICATION This Specification includes a series of annexures that detail additional Requirements . (Not Used) (Not Used) Schedules of HOLD POINTS and Identified Records The schedules in Annexure TS918/C list the HOLD POINTS that must be observed. Refer to Specification RMS D&C Q6 for the definition of HOLD POINTS. The records listed in Annexure TS918/C are Identified Records for the purposes of RMS D&C Q6 Annexure Q/E. Planning Documents The PROJECT QUALITY PLAN must include each of the documents and Requirements listed in Annexure TS918/D and must be implemented.
7 In all cases where this Specification refers to the manufacturer s recommendations, these must be included in the PROJECT QUALITY PLAN. 2 Ed 1 / Rev 0 (RMS COPYRIGHT AND USE OF THIS DOCUMENT - Refer to the Foreword after the Table of Contents) OMCS Requirements - road Tunnel and Underpass Lighting D&C TS918 (Not Used) Referenced Documents Standards, specifications and test methods are referred to in abbreviated form ( AS 2350). For convenience, the full titles are given in Annexure TS918/M. DEFINITIONS AND ACRONYMS Definitions The terms you and your mean the Contractor and the Contractor s respectively. In addition to the definitions given in AS/NZS , the following definitions also apply to this Specification: Cableway System of conduits, including their fittings, pits and equipment housing, but excluding the communication and electrical cables and equipment.
8 Continuous Lighting Near-continuous line Lighting system as defined in CIE 88 Guide for the Lighting of road Tunnels and Underpasses . In such a system, the distance between the end of one luminaire and the beginning of the next luminaire must be less than the total length of the luminaire. Electricity Supply Authority The Electricity Distributor within whose distribution area the electrical installation is situated or where the installation work is carried out. Lamp Replaceable light producing element of the luminaire. A luminaire may comprise one or more lamps. Luminaire An apparatus, which distributes light transmitted from one or more lamps. It comprises the complete assembly including lamps, housing and all the parts necessary for supporting, fixing and protecting the lamps and where necessary, circuit auxiliaries together with the means for connecting them to the electrical power supply.
9 Working width The minimum width required to prevent an impacting design vehicle from colliding with an object situated behind a road safety barrier system. This comprises the dynamic deflection of the road safety barrier (if any) and an extra width to allow for the roll ( vertical rotation) of the impacting vehicle. Acronyms The following acronyms apply to this Specification: HPS High pressure sodium LED Light-emitting diode LEP Longitudinal egress passage OMCS Operations Management and Control System RTUL road Tunnel and Underpass Lighting SIT System Integration Testing Ed 1 / Rev 0 3 (RMS COPYRIGHT AND USE OF THIS DOCUMENT - Refer to the Foreword after the Table of Contents) D&C TS918 OMCS Requirements - road Tunnel and Underpass Lighting SWTC Project Deed Scope of Work and Technical Criteria UAT User Acceptance Testing UPS Uninterruptible power supply 2 DESIGN GENERAL Compatibility The RTUL must be compatible with the OMCS computer systems, equipment and communication networks used for the Motorway.
10 Reliability The RTUL must be reliable, designed to be fault tolerant and fail-safe with layers of redundancy, so that any singular failure of the RTUL components will not adversely impact the operation of the RTUL and overall OMCS. Location Within Carriageway Switchboards, control panels, luminaires, conduits and cables must not be located within the trafficable section or the working width (refer Clause for definition of working width ) of the Tunnel carriageway. Tunnel Lighting General (a) Tunnel Lighting design must be in accordance with AS/NZS , using the operating speeds stated in the SWTC. (b) Provide calculations for the Lighting design demonstrating compliance with the above. (c) Counterbeam or pro-beam Lighting systems must not be used in any part of the tunnels.
