Operation and Maintenance Manual - Tuttnauer USA

1 Operation andMaintenance ManualElectronic Table-Top AutoclavesModels EZ9 Plus & EZ11 PlusCat. No. MAN205-0443001EN RevSManufactured by: Tuttnauer Co. Ltd., Har Tuv Industrial zone B 170, Beit Shemesh99000,Israel Tel: 972 2 9904611, Fax: 972 2 9904730 Tuttnauer Co, Ltd. 25 Power Drive Hauppauge, NY, 11788, USA. Tel (631) 737 4850, (800) 624 5836, Fax: (631) 737 0720 Page1 TABLE OF CONTENTSPARAGRAPHPAGE ANDFUNCTIONS OF Information Control SHOWING A SUCCESSFULLY SHOWING ABORTED CYCLESAFTERA COMPLETED STERILIZATION by user AFTER complete sterilization is open AFTER the sterilization stage has showing a High Pressure Failure AFTER a completed sterilization SHOWING A FAILED CYCLE.

2 Showing a failure because of a Heat Time due to Cancellation by user BEFORE completing the sterilization :WRAPPEDINSTRUMENTS, :CUSTOMA(MAY BE ALTERED BY THE USER).. :CUSTOMB(MAY BE ALTERED BY THE USER).. CHANGING PARAMETERS AND OTHER extra dry to cycle by date and Parameters for Custom A and B a parameter for the Custom A and B Gain and Offset to atmospheric Test (for units with an optional printer).. All Gain and Offset (for units with an optional printer).. (FOR UNITS WITH OPTIONAL PRINTER).. (FOR UNITS WITH AN OPTIONAL PRINTER).. printer on treatment of thermal papers.

3 AND BEFORE ON THE (EZ11 PLUS ONLY).. THE ADDITIONAL DRYING THE THE PROCESSDUE TO CYCLE by the THE WATER OUTLET DOOR pressure from inside the the PARTS OF CONTENT (Cont.)DRAWINGSPAGE the Operating Instructions carefully, before beginning anyoperation on the autoclave! InspectionUpon receiving your Tuttnauer Autoclave, carefully inspect theoutside of the shipping carton for signs of damage. If any damageto the carton is found, note the location with respect to theautoclave and check that area of the autoclave carefully once it isfully unpacked.

4 Observe packing method and retain packingmaterials until the unit has been inspected. Mechanical inspectioninvolves checking for signs of physical damage such as:scratched panel surfaces, broken knobs, any damage is found, contact your dealer as soon aspossible so that Tuttnauer products are carefully inspected prior to shipmentand all reasonable precautions are taken in preparing them forshipment to assure safe arrival at their : Lifting and carrying should always be done by two warrantees, from the date of purchase, all new EZPlusautoclaves for a period of two full years, covering both parts two year warranty covers defects in materials andworkmanship on every part in the autoclaveexceptdoor gasketsand HEPA filters (they are considered wear items).

5 Tuttnauer warrantees the chamber for a period of ten (10)yearsagainst defects in materials and warranty does not include installation or operator instructionwhich are covered in this Manual for your convenience or whichcan be provided by your warranty does not apply to anyinstrument that hasbeen subjected to improper use or accident, nor shall itextend to autoclaves that have been repaired or alteredoutside the factory without prior authorization warranty also does not include routine cleaning orpreventive Maintenance , to be performed according toinstructions in (Preventive and ScheduledMaintenance).

6 Page6 Tuttnauer s obligation is limited to the repair or replacement ofparts for the other warranties or obligations are expressed or Autoclave should only be used in a manner described inthis Manual ! StatementTo activate the warranty, the registration card must be completedand mailed or faxed to Tuttnauer within fourteen (14) days ofpurchase or you may call our customer service department at thenumber listed will only be received and accepted for repair from anauthorized dealer and only with prior return authorization fromTuttnauer. All transportation charges to and from Tuttnauer mustbe paid by the owner of the autoclave.

7 Tuttnauer will not acceptCOD shipments. If repairs are needed during the first 90 daysafter purchase of this autoclave and a local authorized servicedealeris not available, Tuttnauer will arrange pick up of the unit atTuttnauer s expense. This will be on an individually evaluatedbasis andONLY with : If you have any questions or there are any difficulties with thisinstrument and the solution is not covered in this Manual , pleasecontact your dealer or Tuttnauer USA not attempt to servicethis instrument yourself. TuttnauerUSACo.,Ltd.,25 PowerDriveHauppauge,NY11788,USA : (800) 624 5836, (631) 737 4850, Fax: (631)737 INSTRUCTIONSThe autoclave has unique characteristics.

8 Please read and understandthe Operation instructions before first Operation of the autoclave. Thismanual includes instructions and guidance providedby themanufacturer: how to operate the autoclave, the door safetymechanism, and the dangers involved in circumventing safety means,how to ensure that the door is closed, and how to select a correctsterilization sure that you know wherethe main power switch is Maintenance is crucial for the correct and efficient function ofthe use the autoclave to sterilize corrosive products, such as.

9 Acids,bases and phenols, volatile compounds or solutions such asethanol,methanol, chloroform or radioactive are theoperating instructions safety autoclave users must receive training in proper usage from anexperienced employee. Every new employee must undergo atraining period under an experienced sterilizing plastic materials,refer to the item manufactureinformation andmake sure that the item can withstandthesterilization temperature. Plastic that melts in the chamber is liableto cause a great deal of closing the device door, make sure it is properly locked beforeactivating.

10 Verify thattheDOOR OPEN symbol is replaced by System Ready . withdrawing trays, use the enclosed tray handle or wearheat resistant door is electronically locked and will not open unlessthepressure in the chamber equals the atmospheric pressure(chamber pressure is displayed on the screen). door also remains locked if there is a cycle failure or the unithas no the door slowly to allow steam to a month, ensure that the safety valve is operating, and onceevery 5 yearsacertified inspector must performachamberpressuresafety ,breaks,blockages, Maintenance operations as instructed.