Example: tourism industry

Operation Manual - New York State Division of Military and ...

2001, Mercury Marine90-10229021 501 THIS Manual DESCRIBES THE SMARTCRAFT GAUGESYSTEMS AVAILABLE FOR YOUR BOATO peration Manual0 monitor 1 Part 2 Part 3 Part 4 monitor TACH & SPEEDSMART TACH & SPEED1 PRODUCT IDENTIFICATIONFor boats equipped with SmartCraft gauge systems, look tothe descriptions below to identify the system in the read about the SmartCraft system to get the best per-formance from Version & 1 NOTE: Software version willflash on screen at start upMonitorSoftware Version 2 NOTE: Software version willflash on screen at start upSystem Tachometer and SpeedometerPart 3 Note: Look for RESETand Brightness arrowsSmart Tachometer and SpeedometerPart 4 NOTE: Look for letters VDO VDO2 monitor 1 monitor with Software and.

MONITOR 1.01-1.02 1-2 MONITOR – VERSION 1.01-1.02 Basic Operation This monitor is an LCD multi-function display gauge. A variety of dis-plays can be activated using the button. Pressing the button scrolls the following displays: fuel used, tachometer (RPM), fuel flow, power trim position, engine temp, wa-

Tags:

  Monitor

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Other abuse

Transcription of Operation Manual - New York State Division of Military and ...

1 2001, Mercury Marine90-10229021 501 THIS Manual DESCRIBES THE SMARTCRAFT GAUGESYSTEMS AVAILABLE FOR YOUR BOATO peration Manual0 monitor 1 Part 2 Part 3 Part 4 monitor TACH & SPEEDSMART TACH & SPEED1 PRODUCT IDENTIFICATIONFor boats equipped with SmartCraft gauge systems, look tothe descriptions below to identify the system in the read about the SmartCraft system to get the best per-formance from Version & 1 NOTE: Software version willflash on screen at start upMonitorSoftware Version 2 NOTE: Software version willflash on screen at start upSystem Tachometer and SpeedometerPart 3 Note: Look for RESETand Brightness arrowsSmart Tachometer and SpeedometerPart 4 NOTE: Look for letters VDO VDO2 monitor 1 monitor with Software and.

2 Basic Operation1-2.. Standard Information Display Screens1-3.. Shallow Water Alarm1-6.. Warning System1-7.. Warning Display Screens1-7.. CAL 1 Calibration1-9.. CAL 2 Calibration1-12.. NOTE:This Manual shows all the monitor displayscreens that are available. Depending on your typeof engine, not all these screens will with Software Version and iscompatible with:2001 model year and newer Mercury Outboard mod-els that are designed for use with =B =C =D =E =F =I =L =N =O =P =S =T=U== Engine= Fuel= Water Temperature= Water Pressure= Oil= AlarmMONITOR VERSION VERSION OperationThis monitor is an LCD multi-function display gauge.

3 A variety of dis-plays can be activated using the the button scrolls the following displays: fuel used,tachometer (RPM), fuel flow, power trim position, engine temp, wa-ter pressure, battery voltage, range (if calibrated), and water depth(if equipped with transducer).The System monitor will power up when the ignition is turned display includes a backlight which allows you to read it at backlight brightness is adjustable using the event of a warning alarm, the warning icon(s) will be VERSION Information Display Screens Initial Power Up At power up, a momentary (1second) screen displays thecurrent monitor software ver-sion, followed by a 4 second dis-play showing hours of engineuse.

4 Fuel UsedDisplays approximate fuel usedsince the last reset. Reset willreturn display back to can Reset anytime bypressing and buttons together momentarily. Engine RPMT achometer Displays enginespeed in Revolutions Per Min-ute (RPM). Fuel FlowDisplays current estimated indi-vidual engine fuel consumptionin Gallons per hour (Gal/hr) orLiters per hour (Ltr/hr). monitor VERSION Information Display Screens Trim PositionDisplays trim position of the pro-pulsion unit up to the maximumtrim position, and then displaysthe trailer position. 0 = down, 10 = full trim25 = full : This screen can be set topop up whenever the trim switchis used.

5 Refer to the CAL 1 TemperatureDisplays the engine tempera-ture in degrees Fahrenheit ( F)or Celsius ( C). Water PressureDisplays the engine tempera-ture in degrees Fahrenheit ( F)or Celsius ( C). Battery VoltageDisplays voltage level (condition)of VERSION Information Display Screens RangeDisplays estimated rangebased on current fuel consump-tion and fuel remaining in thetank that is connected to thesystem. The number displayedis an estimate of the distanceyou can travel on the remainingfuel at current boat : Two requirements to ac-tivate this screen, 1. you must perform the fueltank calibration in CAL 2.

6 Referto the CAL 2 Calibrations You must have a speed inputdevice connected to the system(paddle wheel or pitot pressuretransducer). Water DepthDisplays the depth of water un-der the transducer if : You must have a depthtransducer connected to thesystem in order for this screen VERSION Water AlarmYou can set an alarm to trigger whenever the boat moves into watershallower than the alarm Shallow Water water depth screen must be displayed. Be sure Depth isturned on in CAL 2. Refer to CAL 2 Calibration both and buttons together for 3 alarm on or off menu will the button to toggle to ON. 5. Push button to depth number will be flashing.

7 Press the button to setthe flashing number to desired alarm depth. 100 ft maximumdepth and 2 ft minimum depth. 7. Push button to VERSION SystemWhen a problem is detected with the engine, the warning displayscreens will alert the operator to the potential problem. Refer to theEngine Operation , Maintenance Manual for explanation of the prob-lem and the correct action to problem can cause immediate engine damage, the Engine GuardianSystem will respond to the problem by limiting engine power. Immedi-ately reduce throttle speed to idle. Refer to the Engine Operation ,Maintenance Manual for further explanation of the problem and thecorrect action to the mode button is pressed to a different screen, the flashing alarmsignal will remain flashing to indicate there still is a Display ScreensIMPORTANT: Refer to the Engine Operation , MaintenanceManual for further explanation of the problem and the correctaction to Water PressureThe Bell and Water Pressureicons are displayed.

8 There is in-sufficient water pressure in thecooling OverheatThe Bell and Temperature iconsare displayed There is insuffi-cient water pressure in the cool-ing Oil ReserveThe bell and oil icons are dis-played. The oil level is criticallylow in the engine mounted oilreservoir VERSION Display ScreensIMPORTANT: Refer to the Engine Operation , MaintenanceManual for further explanation of the problem and the correctaction to Pump FaultThe Bell, Engine and oil iconsare displayed. The oil pump hasstopped functioning lubricating oil is being sup-plied to the in FuelThe Bell and Fuel Icon are dis-played.

9 Water in the water-sep-arating fuel filter reached the fulllevel. Engine OverspeedThe Bell icon is displayed. Theengine speed exceeded themaximum allowable MalfunctionThe Bell and Engine Icon willappear to inform the driver thatan engine problem occurred. monitor VERSION 1 CalibrationCal 1 Display Calibrations: Trim Pop up Screen (On or Off) Trim Sensor Setting English or Metric Readings Selection Range Readings Selection Fuel Tank Capacity ignition key to the on and hold and for 3 seconds to bring up theCAL 1 calibration :Press and hold and for 3 seconds to get out ofthe CAL 1 calibration 1 Start ScreenPress the button to move to the next calibration screen.

10 Trim Pop-up Screen(Turn on or off)Select whether you want thepower trim display screen to popup whenever the trim switch the number flashing on display the button to = on0 = the button to move to the next VERSION 1 Calibration Trim Sensor word Trim and down arrow should be unit to the full Down/In the button to the button to advance to setting. Trim word Trim and down and up arrows should be unit out to the maximum trim (not trailer) the button to the button to advance to setting. Trim word Trim and up arrow should be the trim switch and trim unit out to the maximum trailer the button to the button to move to the next VERSION 1 Calibration SAE English System !


Related search queries