OPERATOR’S MANUAL - Taylor Company

1 operator 'S. MANUAL . Model 150, 152, 162, & 168. Soft Serve Freezers Original Operating Instructions 028749- M. 8/13/08 (Original Publication). Updated 8/3/15. Complete this page for quick reference when service is required: Taylor Distributor: Address: Phone: Service: Parts: Date of Installation: Information found on data plate: Model Number: Serial Number: Electrical Specs: Voltage Cycle Phase Maximum Fuse Size: Amps Minimum Wire Ampacity: Amps Part Number: E 2008 Carrier Commercial Refrigeration, Inc. 028749- M. Any unauthorized reproduction, disclosure, or distribution of copies by any person of any portion of this work may be a violation of Copyright Law of the United States of America and other countries, could result in the awarding of Statutory Damages of up to $250,000 (17 USC 504) for infringement, and may result in further civil and criminal penalties.

2 All rights reserved. Taylor Company a division of Carrier Commercial Refrigeration, Inc. 750 N. Blackhawk Blvd. Rockton, IL 61072. Table of Contents Section 1 To the Installer .. 1. Installer Safety .. 1. Site Preparation .. 1. Air Cooled Units .. 2. Electrical Hook- Up Installation For 60 Cycle, 1 Phase, Supplied With Cord and Plug .. 2. Electrical Connections For Models Without Cord and Plug Supplied .. 2. Beater Rotation .. 3. Refrigerant .. 3. Section 2 To the operator .. 4. Section 3 Safety .. 5. Section 4 operator Parts Identification .. 7. Model 150 .. 7. Model 152 .. 8. Model 162 .. 9. Model 168 .. 10. Models 150 & 152 Door Assembly .. 11. Models 162 & 168 Door Assembly .. 12. Models 150 and 152 Accessories .. 13. Models 162 and 168 Accessories .. 14. Section 5 Important: To the operator .

3 15. Symbol Definitions .. 15. Reset Button .. 16. Power Switch .. 16. Feed Tube .. 16. Taylor Quality Control .. 16. Indicator Light - Mix Low .. 16. Mix Refrigeration Switch .. 16. Separate Hopper Refrigeration (SHR) .. 16. Cylinder Temperature Retention (CTR) .. 17. Section 6 Operating Procedures .. 18. Assembly .. 19. Sanitizing .. 22. Priming .. 23. Table of Contents Models 150, 152, 162, 168. Table of Contents - Page 2. Closing Procedure .. 24. Draining Product From the Freezing Cylinder .. 25. Rinsing .. 25. Cleaning .. 25. Disassembly .. 26. Brush Cleaning .. 26. Section 7 Important: operator Checklist .. 27. During Cleaning and Sanitizing .. 27. Troubleshooting Bacterial Count .. 27. Regular Maintenance Checks .. 27. Winter Storage .. 28. Section 8 Troubleshooting Guide.

4 29. Section 9 Parts Replacement Schedule .. 32. Section 10 Limited Warranty on Equipment .. 33. Section 11 Limited Warranty on Parts .. 35. Note: Continuing research results in steady improvements; therefore, information in this MANUAL is subject to change without notice. Note: Only instructions originating from the factory or its authorized translation representative(s) are considered to be the original set of instructions. E 2008 Carrier Commercial Refrigeration, Inc. (Original Publication). Updated August, 2015. 028749- M. Any unauthorized reproduction, disclosure, or distribution of copies by any person of any portion of this work may be a violation of Copyright Law of the United States of America and other countries, could result in the awarding of Statutory Damages of up to $250,000 (17 USC 504) for infringement, and may result in further civil and criminal penalties.

5 All rights reserved. Taylor Company a division of Carrier Commercial Refrigeration, Inc. 750 N. Blackhawk Blvd. Rockton, IL 61072. Models 150, 152, 162, 168 Table of Contents Section 1 To the Installer The following information has been included in the MANUAL as safety and regulatory guidelines . For complete installation instructions, please see the This unit has many sharp edges that can Installation Checklist. cause severe injuries. Installer Safety Site Preparation In all areas of the world, equipment should be installed in accordance with existing local codes. Please contact your local authorities if you have any Review the area the unit is to be installed in before questions. uncrating the unit, making sure that all possible hazards the user or equipment may come into have Care should be taken to ensure that all basic safety been addressed.

6 Practices are followed during the installation and servicing activities related to the installation and service of Taylor equipment. For Indoor Use Only: This unit is designed to operate indoors, under normal ambient temperatures of S Only authorized Taylor service personnel 70_-75_F (21_-24_C). The unit has successfully should perform installation and repairs on the performed in high ambient temperatures of equipment. 104_(40_C) at reduced capacities. S Authorized service personnel should consult OSHA Standard or the applicable code of the local area for the industry standards on lockout/tagout This unit must NOT be installed in an area procedures before beginning any installation where a water jet or hose can be used. NEVER use a or repairs. water jet or hose to rinse or clean the unit.

7 Failure to S Authorized service personnel must ensure follow this instruction may result in electrocution. that the proper PPE is available and worn when required during installation and service. S Authorized service personnel must remove all metal jewelry, rings, and watches before This unit must be installed on a level surface working on electrical equipment. to avoid the hazard of tipping. Extreme care should be taken in moving this equipment for any reason. Two or more persons are required to safely move this unit. Failure to comply may result in personal injury or The main power supply(s) to the freezer must equipment damage. be disconnected prior to performing any repairs. Failure to follow this instruction may result in personal injury or death from electrical shock or hazardous Uncrate the unit and inspect it for damage.

8 Report any moving parts as well as poor performance or damage damage to your Taylor Distributor. to the equipment. This piece of equipment is made in the USA and has Note: All repairs must be performed by an USA sizes of hardware. All metric conversions are authorized Taylor Service Technician. approximate and vary in size. 131122. Models 150, 152, 162, 168 1 To the Installer Air Cooled Units 4. Route incoming permanent wiring through 7/8 . (22 mm) hole in base pan. 5. Connect two power supply leads. Attach ground (earth) wire to the grounding lug inside the The models 150 and 152 require a minimum of 6 (152. electrical box. mm) of clearance around both sides. Install the skirt provided on the right side of the unit and place the back 6. Be sure the unit is properly grounded before of the unit against a wall to prevent recirculation of applying power.

9 Warm air. The model 162 requires 6 (152 mm) on all sides and the skirt installed on the rear of the unit. The model 168 requires 3 (76 mm) on all sides and the FOLLOW YOUR LOCAL ELECTRICAL CODES! skirt installed on the rear of the unit. Minimum air clearances must be met to assure adequate air flow for optimum performance. These units are designed for indoor use only. Electrical Connections For Models Without Cord and Plug Supplied DO NOT install the units in an area where a water jet could be used. Failure to follow this Each freezer requires one power supply for each data instruction may result in serious electrical shock. label. Check the data label(s) on the freezer for branch circuit overcurrent protection or fuse, circuit ampacity, and electrical specifications. Refer to the wiring diagram provided inside of the control box, for proper power connections.

10 In the United States, this equipment is intended to be Electrical Hook- Up Installation For installed in accordance with the National Electrical 60 Cycle, 1 Phase, Supplied With Cord and Plug Code (NEC), ANSI/NFPA 70- 1987. The purpose of the NEC code is the practical safeguarding of persons and property from hazards arising from the use of electricity. This code contains provisions considered This equipment is supplied with a 3- wire cord and necessary for safety. Compliance therewith and grounding type plug for connection to a single phase, proper maintenance will result in an installation 60 cycle, branch circuit supply. This unit must be essentially free from hazard! In all other areas of the plugged into a properly grounded receptacle. The cord world, equipment should be installed in accordance and plug provided for 115/60/1, is 20 amp; therefore with the existing local codes.