OUTBOARD MODEL CODES - PNEUBOAT.COM

1 1-7 Section 1 General InformationOUTBOARD MODEL CODES1984 TO 1990 CODE GUIDE150 Prop Shaft HorsepowerEElectric StartTPower Tilt or Power Trim & TiltLLower Unit Shaft LengthDModel YearExamples 15 200S = 15 (UR Short) l = 20 (UR long) X = 25 (UR Ultra long) J = Jet Drive lower Unit(UR = User Required) n = 1984 k = 1985 J = 1986 h = 1987 G = 1988 f = 1989 D = 19901991 TO 2005 CODE GUIDEVM odelxFuel Injected150 Prop Shaft HorsepowerTTrim & Tilt/ Power Trim & TiltLLower Unit Shaft LengthRControl MethodAModel YearC = C Series E = Enduro f = four Stroke l = left hand P = Pro S = Saltwater T = four Stroke high Thrust B = Inshore D = Twin Props V = VMAXX = 0X66 Z = hPDIE xample.

2 6 200T = Pwr Trim & Tilt with Electric StartP = Pwr Tilt with Electric StartE = Manual Tilt with Electric StartM = Manual Tilt with Manual StartS = 15 (UR Short) l = 20 (UR long) X = 25 (UR Ultra long) U = 30 (UR Super Ultra long) J = Jet Drive lower Unit(UR = User Required) R = Remote Control h = Tiller handle P = 1991 Q = 1992 R = 1993 S = 1994 T = 1995 U = 1996 V = 1997 W = 1998 X = 1999 Y = 2000 Z = 2001 A = 2002 B = 2003 C = 2004 D = 2005 Four-Stroke Models:Standard four-stroke models are identified by an f before the power rating.

3 High thrust four-stroke models are identified by a T before the power Models: Some special models were produced that did not follow the above MODEL designation procedure. These were the V6 Special (220hp), V6 Excel (225hp), CV and the PRO models. Each of these models did include shaft length and year indicators in their MODEL namesNOTE: Early models, 1984 to 1986, also had a factory production MODEL variation code marked on the engine similar to: 150 AETO. This code does not contain any MODEL year indicator and can be special attention to every section of the MODEL MODEL IDENTIFICATION(b) (c) (a) (d)(a) MODEL NAME(b) PREFIx MODEL CODE(c) TRANSOM LENGTH(d) SERIAL NUMBER1-8 NOTE: After 2005 MODEL year production, new models being produced will no longer have the last letter of the MODEL code which typically has designated MODEL Year ( 90 TlRD will now be 90 TlR).

4 Engines produced in April 2005 and later will require the complete PID ( MODEL code and serial number) to locate the proper service and parts 2005 AND NEWER PRODUCTION MODEL NAME GUIDEVM odel Description xFuel Induction 150 Prop Shaft Horsepower BNew MODEL Designator TStarting/Tilt Method LShaft Length RControl Method B = Inshore SeriesC = C SeriesD = Twin PropellersE = Enduro Seriesf = four Strokel = Counter RotationP = Pro SeriesS = Saltwater SeriesT = high ThrustV = V MAX SeriesZ = hPDI (high Pressure Direct Injection)

5 F = f our StrokeX = OX66 Advanced fuel InjectionZ = hPDI (high Pressure Direct Injection) letter appearing between Prop Shaft horsepower and Starting/Tilt Method is a new MODEL Designator . Where used, these distinguish enhancement(s) to an existing OUTBOARD MODEL sufficient to deem it a new MODEL , or a com-pletely new OUTBOARD that is a direct replacement of an existing OUTBOARD = Power Trim and Tilt MODEL with Electric StartP = Power Tilt with Electric StartE = Manual Tilt with Electric StartM = Manual Tilt with Manual StartS = 15"l = 20"X = 25"U = 30"J = Jet Drive UnitR = Remote Controlh = Tiller handle1-9 Section 1 General InformationModel Code Changes for F40 ModelsIn order to simplify Yamaha MODEL CODES and the introduction of new models.

6 Yamaha has revised its MODEL code designators (starting with this all-new engine). Please note that all other Yamaha engines will retain their current models CODES until further F 40 B T X R Fuel Induction Horsepower MODEL Code Starting Method Shaft Length Control Method Designator F = 4 stroke B = 3 Star T = PTT & E start S = 15" R = Remote control CARB P = PT & E start L = 20" H = Tiller handle Rating E = Electric start X = 25" M = Manual start U =30" J = Jet F 40 L E H A Fuel Induction Horsepower Shaft Length Starting Method Control Method

7 Generation PTT F = Four Stroke S = 15 Blank = PTT & E start Blank = Remote A = 1st change on motor L = 20 P = PT & E start Control B = 2nd change on motor X = 25 E = Electric start H = Tiller Handle C = 3rd change on motor U = 30 M = Manual start C = Command Link Etc. J = Jet Control F 40 L A Fuel Induction Horsepower Shaft Length Starting Method Control Method Generation PTT F = Four Stroke S = 15 Blank = PTT & E start Blank = Remote A = 1st change on motor L = 20 P = PT & E start Control B = 2nd change on motor X = 25 E = Electric start H = Tiller Handle C = 3rd change on motor U = 30 M = Manual start C = Command Link Etc.

8 J = Jet Control F 40 J E H A Fuel Induction Horsepower Shaft Length Starting Method Control Method Generation PTT F = Four Stroke S = 15 Blank = PTT & E start Blank = Remote A = 1st change on motor L = 20 P = PT & E start Control B = 2nd change on motor X = 25 E = Electric start H = Tiller Handle C = 3rd change on motor U = 30 M = Manual start C = Command Link Etc. J = Jet Control F 40 J E A Fuel Induction Horsepower Shaft Length Starting Method Control Method Generation PTT F = Four Stroke S = 15 Blank = PTT & E start Blank = Remote A = 1st change on motor L = 20 P = PT & E start Control B = 2nd change on motor X = 25 E = Electric start H = Tiller Handle C = 3rd change on motor U = 30 M = Manual start C = Command Link Etc.

9 J = Jet Control Please note all other Yamaha OUTBOARD models will continue to use the current MODEL code system at this time. Generation CODES will change at such time new Yamaha outboards models are CODES will utilize this new and simpler format at that = four-Strokef = four-Strokef = four-Strokef = four-Strokef = four-Strokecurrent MODEL CODES until further = Remote Control h = Tiller handl