Owner's Manual

1 Designed and Handcrafted in the USAArtSeries AmplifiersOwner' W. Detroit Street Suite 180 Chandler, AZ 852261-800-62-POWERCONGRATULATIONS AND THANK YOUforyourchoiceofaPrecisionPower, Inc. high performance mobile audio proud to be a world leader specializing in thedesign, engineering, and manufacture of "State of the Art" mobileaudio electronics. Our success is derived from the fact that we do notincorporate gadgets or passing fads into our products. Soundengineering practice, combined with deceptively simple yet highlyeffective circuit designs, characterize everyPPIproduct.

2 Yet, ourdemand for maximum value dictates that every ounce of fat betrimmed if it does not contribute to sound quality or reliability. This iswhyPPIproducts have consistently enjoyed an unparalleledreputation for sound value. We are sure that your new Art Seriesamplifier will provide you the "State of the Art" in mobile Audio ElectronicsImportant SafeguardsThe following list of 'Important Safeguards has been compiled to help you achieve optimum satisfaction andthe highest quality performance from your new mobile audio amplifier. Please take the time to review thesesafeguards before operation and or installation of your new Art Series InstructionsWe all have a tendency to read instructions only after something doesn't work as anticipated.

3 This manualprovides specific information concerning the operation and installation of your new amplifier. Please readthis Manual thoroughly and retain it for future Your Sales ReceiptYourPPIamplifier has a three-year limited warranty when it is installed by an AuthorizedPPIdealer. Non-Authorized dealer installed (PPI) amplifiers carry a one-year parts / ninety days labor limited warranty. Toestablish the starting date of warranty coverage, a copyof your sales receipt must accompany your amplifierfor all warranty service. Please file your sales receiptaway for future reference.

4 For your convenience, acomplete limited warranty statementis located at the back of this InstructionsAll use and installation instructions should be followed to assure proper operation of your new Art All Wiring RequirementsAhigh-performance amplifier requires minimum wire gauges be used for the Power, Ground, Remote Tum-On, and Speaker cables. To assure proper operation of your Art Series amplifier, following all all Fusing RequirementsThe fusing requirements of your Art Series amplifierhave been established for its continued safe with a higher value fuse may result in damage and voiding of AccessoriesThe Art Series amplifiers will require non-supplied installation accessories.

5 Please refer to the InstallationSection of this Manual for a list of requirements or consult your AuthorizedPPIdealer before and MoistureNever mount your Art Series amplifier in a location which would subject it to immersion or exposure to not attempt to service this amplifier yourself. Opening or removing covers will void your warranty. Forservice information, consult your Authorized PPI dealer or call PrecisionPower, customer service representatives are available Monday through Friday from 8am to 5pm MountainStandard !The use of a high-powered audio system may cause hearing loss or damage.

6 While PPIsystems are capable of "Concert level" volumes with incredible accuracy, they aredesigned for you to enjoy the subtleties created by musicians while listening atreasonable sound pressure levels. The use of a high powered audio system may impairyour ability to hear traffic sounds, and therefore, may constitute a traffic hazard. Weadvise lower volume levels while of ContentsGlossary of Terms4 Features5 Specifications6 About Your Art Series Amplifier7 Installation11 System Tuning15 Troubleshooting17 System Designs18 Limited Warranty20 PPIG lossaryAM IIAdaptive MOSFET II is an advanced protection circuitdesigned to prevent amplifier shut-off due to low load imped-ance.

7 AM III optimizes output power to maintain uninterruptedoperation whenever the amplifier senses a load impedance ofless than two Ohms. An L. E. D. signals when AM II is :Combining two amplifier channels into one channel, typicallyused to create a mono :The ratio of output voltage to input voltage. The gain controlallows adjustment to the amplifier's output level for varyinginput :Light Emitting Diode. Indicates power on / off and when AMIIis Impedance:Measurement of speaker(s) resistance / reactance that theamplifier must Mono:The amplifier's ability to play the Left and Right Stereo channelswhile playing a third (bridged) mono Modulated power supply.

8 Our PWM maintains aregulated output voltage and a high conversion efficiency overthe input supply range of 11 - 15 VDC. The result is less demandon the battery, lower (amplifier) operating temperature, andextremely accurate low frequency Turn-On:Low current automatic switchingcircuit that turns the amplifieron and off. Typically connected to the remote antenna or ampturn-on lead of most car radios, cassette, or CD following terms are used in this Manual . Since they may be unfamiliar, thefollowing definitions are Control (optional) controls upto tenPPIamplifiers for synchronized system start and "noisegate" functions to inhibit background noise when no musicsignal is / / / / / Modulated (PWM)

9 Switching Power Supply for High-EfficiencyRegulated Power Supply Provides Full Rated Power from 11 - 15 VDCD iscrete Power Amp CircuitryInternally BridgeableMixed Stereo / Mono OperationOutput Short Circuit ProtectionDifferential Input StageLow Impedance Protection with Diagnostic Input SensitivityGold RCA Input ConnectorsPPI's Exclusive Wire Connection SystemLiquid Cooling (Optional)Amplifier Control Module Compatible (Optional ACM-420)Three Year Limited WarrantyDesigned and Handcrafted in the USAT echnical SpecificationsArt Series Power Output per Channel:4 Ohms, 11-15 VDC, Stereo:25 Watts50 Watts75 Watts150 Watts 300 Watts2 Ohms, 11-15 VDC, Stereo:50 Watts100 Watts150 Watts300 Watts 600 Watts4 Ohms, 11-15 VDC,Bridged:100 Watts200 Watts300 Watts600 Watts 1200 WattsPower Fuse:20 Amp20 Amp30 Amp40 Amp100 AmpDimensions (inches) "Shipping Specifications:Power Bandwidth:10 Hz -50 kHzTotal Harmonic Distortion.

10 02%Input Sensitivity:.2 - VInput Impedance:10k OhmsLoad Impedance (Stereo):2 - 8 OhmsLoad Impedance (Bridged):4 - 8 OhmsSupply Voltage:11 - 15 VoltsAbout your New Art Series AmplifierAs a world leader in the design and manufacture of high-performance mobile amplifiers,PrecisionPower, Inc.'s commitment to being: Absolutely Start of the Art demands thatwe create products that offer high reliability and superior sound quality. To do this, wemust recognize and find solutions to the unique problems, which affect the performanceof electronics in the mobile , we build upon experience.