Example: tourism industry

Package - Loctite® Equipment Support | Henkel

Package Totes Drums Pails STANDARD AUTOMATAN PRODUCTS. PRODUCTS Aquence LA 117A Aquence LA 5023M Aquence LA 626A Aquence LA 155A Ultimate Control . Ultimate Control Ultimate Control Ultimate Control (Trouble Shooter). (General Purpose) (Best Dextrine) (Resin Dex) TYPE Dextrin Adhesive Dextrin Adhesive Resin Dex High Performance Formulated Emulsion APPEARANCE Tan, fluid product Tan, fluid product White, fluid product Fluid emulsion adhesive SOLIDS Approx. 50% Approx. 56% Approx. 45% Approx. 52%. VISCOSITY Approx. 2000 cps Approx. 2800 cps Approx. 1200 cps Approx. 1200 cps pH Approx. Approx. Approx. Approx. Approx. Approx. Approx. Approx. Faster than 5023M . SUGGESTED USES CRITICAL-TO-QUALITY (CTQ) REQUIREMENTS. Layflat laminating. Meets composition requirements of Indirect Tack The glue must be able to hold the label or top sheet in Food Additives Regulation 21 CFR Adhesives. place through the entire process until the final bond is set. Any delamination is considered scrap or waste and is unusable.

Except as otherwise noted, all marks used are trademarks and/or registered trademarks of Henkel and/or its affiliates in the U.S. and elsewhere. ® = registered in the U.S. Patent and Trademark Office.

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Other abuse

Transcription of Package - Loctite® Equipment Support | Henkel

1 Package Totes Drums Pails STANDARD AUTOMATAN PRODUCTS. PRODUCTS Aquence LA 117A Aquence LA 5023M Aquence LA 626A Aquence LA 155A Ultimate Control . Ultimate Control Ultimate Control Ultimate Control (Trouble Shooter). (General Purpose) (Best Dextrine) (Resin Dex) TYPE Dextrin Adhesive Dextrin Adhesive Resin Dex High Performance Formulated Emulsion APPEARANCE Tan, fluid product Tan, fluid product White, fluid product Fluid emulsion adhesive SOLIDS Approx. 50% Approx. 56% Approx. 45% Approx. 52%. VISCOSITY Approx. 2000 cps Approx. 2800 cps Approx. 1200 cps Approx. 1200 cps pH Approx. Approx. Approx. Approx. Approx. Approx. Approx. Approx. Faster than 5023M . SUGGESTED USES CRITICAL-TO-QUALITY (CTQ) REQUIREMENTS. Layflat laminating. Meets composition requirements of Indirect Tack The glue must be able to hold the label or top sheet in Food Additives Regulation 21 CFR Adhesives. place through the entire process until the final bond is set. Any delamination is considered scrap or waste and is unusable.

2 OPERATING CONDITIONS. Open Time Open time must suit the type of machine the plant is using. If Direct transfer from wheel, roller or stencil. Stir thoroughly before a glue is too aggressive, the glue may set prior to reaching compression or using. Ready-for-use viscosity as supplied. (May be diluted with on some machines (bulk) set prior to the squaring section. water if desired). Wet-film soluble in warm water. Dry-film soluble in acetone/water. Machining If a glue slings or sprays, it may form buildup and actually interfere with the machine's ability to run. This can cause PRECAUTIONS downtime to clean or remove jam-ups. Protect from temperatures below 40 F. Rotate stock using Flat Board (layflat) If the board is not flat, the feeders oldest material first. Keep covered to prevent drying out and on the folder gluers may work at normal speeds, contamination. Do not mix with other adhesives. resulting in lower throughput. Except as otherwise noted, all marks used are trademarks and/or registered trademarks of Henkel and/or its affiliates in the and elsewhere.

3 = registered in the Patent and Trademark Office. Automatan is a trademark of Automatan Incorporated. Henkel Corporation, 2013. All rights reserved. 9730 (1/13).


Related search queries