PACKAGE TERMINAL AIR CONDITIONER/HEAT PUMP …

1 This manual must be left with the owner of the TERMINALAIR CONDITIONER/HEAT PUMPINSTALLATION INSTRUCTIONS & OWNER S MANUALS tandard and Remote Applications with LED ControlIO-447B03/2017 is a registered trademark of Maytag Corporation or its related companies and is usedunder license to Goodman Company, , Houston, TX, USA. All rights INSTALLING PERSONNELAs a professional installer you have an obligation to know theproduct better than the customer. This includes all safety pre-cautions and related to actual installation, thoroughly familiarize yourself withthis Instruction Manual.

2 Pay special attention to all safety during installation or repair it is possible to place yourselfin a position which is more hazardous than when the unit is , it is your responsibility to install the product safelyand to know it well enough to be able to instruct a customer inits safe is a matter of common matter of thinking beforeacting. Most dealers have a list of specific good precautions listed in this Installation Manual are intended assupplemental to existing practices. However, if there is a directconflict between existing practices and the content of this manual,the precautions listed here take San Felipe, Suite 500 Houston, TX 77056 2014 - 2015, 2017 Goodman Company, 2 Installation 7 Operating 8 Maintenance and 12 Obtaining Service.

3 14 Normal Operating Sounds and Conditions .. 14 Configuration Settings .. 14 Configuration Chart .. 15 Diagnostic Maintenance & Status Report .. 16 Diagnostic 17 UNIT FEATURESThis unit has many features which are different than those foundon conventional PTAC units. The servicer must be familiar withthese features in order to properly service the unit. LCDI or AFCI Power Cords - Underwriters Laboratoriesand the National Electric Code (NEC) now require powercords that sense current leakage and can open the elec-trical circuit to the unit on units rated at 250 volts orless. In the event that unit does not operate, check thereset button located on or near the head of the powercord as part of the normal troubleshooting power Cord Automatic 3-minute compressor lockout - After the com-pressor cycles off, it will not restart for three minutes.

4 Automatic 2nd stage electric heat - If the room tempera-ture falls to 4 F below the set point temperature, thereverse cycle heat is shut off and the electric strip heat isturned NOTE TO THE OWNERThis manual is to be used by qualified, professionally trainedHVAC technicians only. Goodman does not assume any respon-sibility for property damage or personal injury for improperservice procedures or services performed by an NOTES:Your warranty certificate is also supplied with the the warranty carefully and note what is the warranty certificate in a safe place, so you canfind it, if using this manual, check the serial plate forproper model INSTALLATION AND SERVICING OF THIS EQUIPMENTMUST BE PERFORMED BY QUALIFIED, EXPERIENCED TECH-NICIANS to policy of continual product improvement.

5 Theright is reserved to change specifications and designwithout THIS SYMBOLAS A SAFETY WILL NOT BE RESPONSIBLE FOR ANY INJURY OR PROPERTYDAMAGE ARISING FROM IMPROPER SERVICE OR SERVICE YOU INSTALL OR PERFORM SERVICE ON THIS UNIT, YOU ASSUMERESPONSIBILITY FOR ANY PERSONAL INJURY OR PROPERTY DAMAGE WHICHMAY RESULT. MANY JURISDICTIONS REQUIRE A LICENSE TO INSTALL ORSERVICE HEATING AND AIR CONDITIONING NOTE TO THE SERVICERRead this manual and familiarize yourself with the specific itemswhich must be adhered to before attempting to service this precautions listed in this Installation Manual are intended assupplemental to existing practices.

6 However, if there is a directconflict between existing practices and the content of thismanual, the precautions listed here take Automatic freeze protection - Whenever power is sup-plied to the unit and the master switch is in the ON posi-tion, automatic freeze protection is active. If the unitsenses temperature below 40 F, the fan motor and elec-tric strip heat are turned on. Freeze protection can beturned off, if required. Random restart delay - To help eliminate power surgesafter a power outage, the unit is equipped with a two tofour minute random restart delay feature.

7 Whenever theunit is plugged in with the master switch turned on andthe mode switch set in the cool or heat mode, a randomrestart will occur. A random restart condition can beavoided by setting the mode switch in the fan only or offposition before applying power to the unit. Fuse holder - On all 265 volt units, fuse holders are fac-tory installed. Check for blown fuse if unit does not oper-ate. Fuse holder is located behind the front. Replacementfuses may be purchased from the Parts Department orcontact your sales representative for part Panel Indication LEDs - The touch pad has LEDs that correspondto fan operation and to indicate unit status.

8 The LEDsnext to the selections OFF, COOL, and HEAT indicate whichoperational mode is active. The LED located in the lowerleft corner is a status LED. This LED indicates the status ofthe unit. See Diagnostic Maintenance & Status Report sec-tion for further Button Touch Pad With Display Load shedding - When input terminals have been config-ured for load shedding operations. If at any time a switchis closed between the IN1 and COM or IN2 and COM termi-nals as configured, the compressor and electric heaterwill lockout until the switch is : The PTAC Wire Harness Kit (PWHK01G70) is required whenusing or load shedding option.

9 Transfer fan - A daughter board allows for an external(transfer) fan connection. A user-supplied relay is requiredand, depending upon the type used, an approved externaltransformer kit may be required for installation. Front mounting hole - A mounting hole location is pro-vided to give the owner the option of securing the front tothe chassis. The mounting hole must be drilled at thedimple indicating the correct location below a louver. Theowner must supply one 1/2 inch long #8 sheet metal screwper unit. The screw must be removed before the front canbe Mounting screw accessedthrough louvers.

10 Chassis Front4 Energy Management System FeaturesTemperature Setback - This option can save energy dol-lars for unrented or unoccupied rooms by automaticallysetting back the operational temperatures. This mode ofoperation is selected through the configuration routine(see Configuration Settings section). NOTE: Temperaturesetback does not work with a wired remote Switch and Motion Sensor Low Voltage Terminals (IN1,IN2, COM) - The door switch and motion sensor operate asa unit, the terminals allow for wired connection of a doorsensor to the control board. The motion sensor interpretsany door movement as a signal of occupancy.