Pecaform™ - Parchem

1 Technical Data SheetPage 1 March 2015 Pecaform Versatile Lightweight Formwork SystemDescriptionPecaform is supplied in sheet form and consists of a steel wire mesh with a heat shrunk layer of polyethylene applied to both sides of the combination creates a material that is both light and structurally strong, making it extremely easy to Lightweight Multiple shapes Variety of applicationsUsesPecaform is a flexible versatile form working material perfect for those radius specifications. The strength and versatility of Pecaform make it the natural choice for the following applications: Ground beams Footings and bases Pile caps Construction joints (stop ends) Special shapes or curves Void formation Ribbed and waffle slabs Penetrations Recesses Temporary fencing Safety screensBenefitsPre-formedPecaform can be pre-formed and delivered to site ready for assembly or it can be simply folded on site using a manual speed formworkPecaform is designed for fast assembly.

2 No hammer, nails or saws, just installation procedureBecause it is supplied in sheets or can be pre-formed, it is easily assembled using on site SafetyPecaform can provide enhanced site safety by: Back filling excavations earlier than with conventional formwork Minimising need for workers to be in excavations Reduces the heavy labour needed for conventional formwork Eliminates the need to strip formworkPage 2 Pecaform Properties STANDARDOTHER PECAFORM TYPES AVAILABLE UPON REQUESTVR6VR4VR8VR10 Main wire size (nominal) mm diameter4 mm mm mm diameterMain wire spacing:150 mm c/c100 mm c/c150 mm c/c150 mm c/cCross wire size (nominal):4 mm diameter4 mm diameter4 mm diameter4 mm diameterCross wire spacing:75 mm c/c100 mm c/c75 mm c/c75 mm c/cWire specification:high tensile steel of tensile strength 485 N/mm non galvanisedhigh tensile steel of tensile strength 485 N/mm non galvanisedhigh tensile steel of tensile strength 485 N/mm non galvanisedhigh tensile steel of tensile strength 485 N/mm non galvanisedGalvanised code (wire):VR6G - galvanisedVR4G - galvanisedVR8G - galvanisedVR10G - galvanisedPolyethylene mm thick - one layer each mm thick - one layer each mm thick - one layer each mm thick - one layer each sidePolyethylene colour (*):Black/ kg/m kg/m kg/m kg/m Pecaform VR6 is generally stocked in Australia; other types are available to order in as requiredHow strong is Pecaform?

3 To demonstrate the strength of Pecaform as a form work system, a sheet of Pecaform was bent into a 450mm square x 1200 mm high form to replicate a form that would be used for a footing. The base was restrained by wood blocks, and three straps were used to hold the form body together. Two reinforcing bars were inserted through opposite sides. The inside of the form was then filled with ready mixed can be seen in the photograph, a minor amount of bulging is evident on the sides, but no other distress to the Pecaform is indicated. No leakage is visible, and there is no evidence of leakage at the locations where the reinforcement bars penetrated the Pecaform is primarily intended as a sub-grade formwork system that is backfilled on the outside of the form before the concrete is poured, bulging of the sides will be negligible, as the sides will be restrained by the 3 Pecaform Method of Application - Pile Cap & Bases1.

4 Apply lean concrete blinding after pile cap Fix reinforcement cage and provide the necessary spacing from the blinding to allow for the concrete Place Pecaform around perimeter of pile cap after strategically securing strips of long spacers or Backfill excavation up to 150 mm from the top of the Pecaform to avoid Pour and vibrate the concrete in accordance with good concreting The Pecaform remains in the - BasesBases can be constructed from either L-shapes or flat strips of Pecaform similar to either beam or pile cap construction. Lean concrete blinding is applied in the traditional manner, and the reinforcement cage complete with spacer blocks at the bottom is lowered onto the is then placed against the side of the cage and spaced off the reinforcement with strips of long spacers, bar chairs or excavation up to 150mm from the top of the Pecaform to prevent OptionsGround beams can be divided into two categories:1.

5 Suspended beams (on piled foundation)The ground on which the beam is constructed should be capable of safely supporting the weight of the wet concrete during construction. Only nominal surface compaction is required and a thin layer of sand blinding to level the formation and bed-in the beam soffit may be Ground bearing beamsThese are founded in the bearing strata. Therefore, a thin layer of sand may be used as blinding to bed-in the Pecaform. Unless supported independently, Pecaform relies on back fill to counteract the pressure exerted by the concrete pour. Suitable spacers attached to the reinforcement cage ensure the beam profile is OptionsPecaformL-ShapesBackfillBlindingF ixing PinL-shapes below blinding150150 Fixing PinBlindingL-shapes above blindingBackfillPecaformL-ShapesPage 4 Pecaform Support TechniquesGirdersFor beams and footings up to and including m in depth, where the Pecaform formwork is required to be re-used several times, the fastest and easiest technique is the girder system.

6 This consists of a system of tie rods and girders strategically placed to give rigidity to the system during concreting. A simple locking mechanism at each end of the tie rod is designed to lock or unlock the girder and Pecaform with great ease and speed. The Pecaform girder system for foundation forworking consists of: Pecaform VR6 Tie rods and locking nailsThe Pecaform foundation formworking system represents the most economical alternative to conventional backfill methodPecaform is supplied in U-shapes for beams and pre-formed strips for footings to form the required profiles. These are assembled on the blinding, wired together, and lined up. Placing approximately 200mm of backfill against the Pecaform stabilises the material prior to the concrete should continue together with the concrete pour to counteract the increasing pressure on the Pecaform as the level of the concrete pour rises. Backfilling is required up to within 150mm from the top of the beams and footings to avoid timbers are recommended to maintain the beam width, but once the pour reaches the top of the Pecaform these should be removed to allow vibrating and surface finishing of the JointsPecaform is a suitable material for construction joints.

7 Depending on the depth of concrete to be retained, support methods may foundations such as those used for high rise buildings have many construction provides a tearproof formworking membrane which allows starter bars to be fixed in position without drilling. The timber joist bracing for the Pecaform will also act as a support for the 5 Parchem Construction Supplies Pty Ltd7 Lucca Road, Wyong NSW 2259 Phone: 1300 737 80 069 961 968 Distributed in New Zealand by: Concrete Plus Ltd23 Watts Rd, Sockburn 8042 Ph: 03 343 0090 Important noticeA Safety Data Sheet (SDS) and Technical Data Sheet (TDS) are available from the Parchem website or upon request from the nearest Parchem sales office. Read the SDS and TDS carefully prior to use as application or performance data may change from time to time. In emergency, contact any Poisons Information Centre (phone 13 11 26 within Australia) or a doctor for disclaimerThis Technical Data Sheet (TDS) summarises our best knowledge of the product, including how to use and apply the product based on the information available at the time.

8 You should read this TDS carefully and consider the information in the context of how the product will be used, including in conjunction with any other product and the type of surfaces to, and the manner in which, the product will be applied. Our responsibility for products sold is subject to our standard terms and conditions of sale. Parchem does not accept any liability either directly or indirectly for any losses suffered in connection with the use or application of the product whether or not in accordance with any advice, specification, recommendation or information given by Performance DimensionsPecaform Conventional (Timber/Plywood)Aluminium/ Steel FormworkAdvantages of Pecaform Speed:FasterSlowerMedium Early completion Saving in preliminaries cost Client incentives Less dependent on weatherInvestment cost:LowLowHigh Low costLabour requirement:LowerHigherMedium Less reliance on skilled labour lower labour costSkills:General WorkersSkilled Carpenters & General WorkersSkilled Workers Saving in labour cost Availability > speedInstallation:Light & easyTedious & time consumingSimple but skilled labour required Saves time Saving in labour costDebris removal.

9 Not requiredRequiredNot required Saving in debris removal cost Save the environmentLifting device / cranageMan handledCranage requiredCranage required Smaller storage space More working spaceStorage requirement:MinimumHighHigh Saving in machinery/cranage cost Saving in operator costFormwork removal:Not requiredRequiredRequired Saves timeEnvironmental acceptance:Environmental friendlyHigh rate of timber consumption & burningEnvironmental friendly Enhance corporate image Complies with legislation Save the environmentSite cleanliness:Neat and cleanUntidy, dangerous and hazardousNeat & clean Enhance site safety Enhance corporate image Improve productivityCorporate image:ExcellentPoorGood Enhance corporate imageSupplyPecaform VR6: Standard Sheet Sizes Product Code: 2500649 - 600 x 2250 mm 2500650 - 900 x 2250 mm 2500651 - 1200 x 2250 mm 2500652 - 1500 x 2250 mm 2500653 - 1800 x 2250 mm