Portable Electric Oil-Free Air Compressor

1 Operating Instructions & Parts ManualENPortable Electric Oil-Free Air CompressorModel 45PL19 PLEASE READ AND SAVE THESE INSTRUCTIONS. READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE! RETAIN INSTRUCTIONS FOR FUTURE REFER TO BACK COVER FOR INFORMATION REGARDING DAYTON S WARRANTY AND OTHER IMPORTANT #: _____Serial #: _____Purch. Date: _____Printed in Taiwan 2016 Grainger, Rights ReservedBEFORE YOU BEGING ettinG StartedSafety / SpecificationSaSSembly / inStallationoperationtroubleShootinGmain tenance / repair See General Safety Instructions on page 2, and Cautions and Warningsas requirements: 115 VAC, 60 Hz, 12 AmpsuNPACkiNgSteps:1.

2 When unpacking the unit, carefully inspect for any damage thatmay have occurred during Check for loose, missing or damaged parts before putting theunit into Contact the shipping carrier directly for any damage SAFETY INFORMATIONG ettinG StartedSafety / SpecificationSaSSembly / inStallationoperationtroubleShootinGmain tenance / repair2 Risk of Fire. Do not spray combustible or flammable liquid in a confined area, spray area Risk of Electrical Shock. Disconnect Compressor from electrical supply circuit before of Explosion. Disconnect Compressor from electrical supply circuit before be well ventilated.

3 Do not smoke while spraying or spray where spark or flame is present. Keep Compressor at least 12 ~ 18 feet away from spraying area and all explosive not expose Compressor to rain or operate in a wet area. Never use the air Compressor without connection to a properly grounded outlet with the specified voltage and fuse protection. Improper grounding can result in electrical not repair, modify or weld tank, return to authorized service center if replacement is required. Do not adjust regulator to result in output pressure greater than allowable maximum pressure which is shown in the specification.

4 Pressure switch is set at the factory for optimum performance of your particular model, never bypass or remove pressure switch as serious damage to equipment or personal injury could result from improper pressure setting. Before starting Compressor , pull pressure relief valve ring to make sure the valve moves freely. The pressure relief valve is factory installed to prevent the air tank from damage should malfunction occur in the pressure switch. It is factory set at a specific limit for your particular model, and should never be tampered with. Adjustment by user will automatically void warranty.

5 Product DescriptionBody color SpeedAire Green powder coat of ConstructionAluminum Alloy Cylinder, ASME certified steel tank. Advantage or benefitCompact design and light weight for easy pump is maintenance Air Inflation Accessories, Air Brush, Brad Nailers and Staplers, Caulk Gun, Grease Gun, Engine Cleaner. Other informationPortable Electric Oil-Free Air Compressor , Hot Dog Tank Type, Weight 40 SAFETY INFORMATIONG ettinG StartedSafety / SpecificationSaSSembly / inStallationoperationtroubleShootinGmain tenance / repair3 Risk of Burns. Use respiratory protection in a well ventilated area when from Moving Parts.

6 Unit starts automatically, do not operate with broken guards or covers Risk from Flying Objects. Always wear ANSI approved safety glasses with side shields whenCompressed air from the unit may contain poisonous vapour which is not suitable for inhaling and could be harmful to your health. Work in an area with good Any repair required on the product should be performed by authorized service center personnel. Do not touch moving parts. using the air Compressor . Always wear proper safety equipment while using compressed air. Do not direct high pressure air stream toward any parts of the body or at other people.

7 Unplug power cord and drain air from tank before servicing and whenever you leave for the : Risk of Property Damage when Transporting Compressor . Always place Compressor on a protective mat when transporting to protect against damage to vehicle. Always operate Compressor in a stable position to prevent accidental movement of the StartedSafety / SpecificationSaSSembly / inStallationoperationtroubleShootinGmain tenance / repair4 Diagramsgrainger items TankMotor RatingsCFM RatingsPressure RatngsLube RequirementsMotor Type 45PL19 Hot DogTankType, Tank Size 3 galHP ,115 VAC Voltage, Full Load Amps Air CFM @90 PSI , free AirCFM @ Pressure135 psi,dBA @3 OilFree,CSA StandardsMotor RPM3100, Universal Motor Type, Avg.

8 PumpLife 1,200hr grainger items No. Length ( )Width ( )Height ( ) (inch)SPECiFiCATiONS GettinG StartedSafety / SpecificationSaSSembly / inStallationoperationtroubleShootinGmain tenance / repair5iNSTALLATiON iNSTRuCTiONSinstall:Electrical:Do not expose the Compressor to normal conditions, the air compressorwill operate intermittently. Should it be necessary IMPORTANT: Locate the Compressor in a clean, dry and well-ventilated area. The Compressor should be located 12 ~ 18 inches from a wall or any other obstruction that would interfere with the air flow. IMPORTANT: The air Compressor is designed with heat dissipationfins that allow for proper cooling.

9 Keep the fins and other partsclean. A clean air Compressor runs cooler and provides longerservice. Allow room for easy access to the air Compressor formaintenance and service : Place the air Compressor on a firm and level surface. Failure to connect the air Compressor correctly to the power source may result in serious personalIf the power cord is damaged, it must be replaced by a qualified electrician in order to avoid a injury or damage to the service, ensure the power source ha sbeen shut down to prevent personalinjury or damage to the unit. Ensure the air Compressor is electrically connected in a safeand correct manner.

10 Any electrical work should be carried out by a qualifiedelectrician and installed in a way that meets all applicable codesand StartedSafety / SpecificationSaSSembly / inStallationoperationtroubleShootinGmain tenance / repairOPERATING INSTRUCTIONS61. Thermal Reset Switch2. Pressure Switch3. Air Pressure RegulatorIMPORTANT: Ensure that all guards and shrouds are in place before pressing reset switch to restart the motor. If the motor shuts down because of overload, wait 10-15 minutes for the motor to cool down, and then press the reset switch to restart motor.