Pre-Installation Manual - MC Bowling

1 Bowling IS SOLD ON brunswick . Bowling EQUIPMENTWITH A-2 PINSETTERSE lectrical RequirementsB-0195-033/95 Pre-Installation ManualLane Boss, Lustre Kleen, Tel-E-Foul, and GS-96 are registered trademarks ofBrunswick Bowling and Billiards March, 1995 by brunswick Bowling and Billiards Corporation. All rights Manual - brunswick Bowling EQUIPMENT WITH A-2 PINSETTERSELECTRICAL REQUIREMENTSR eorder Part No. B-0195-03 Confidential material under NOT reproduce or Bowling and Billiards Corporation525 W. Laketon Box 329 Muskegon, MI 49443-0329 Table of 1 Notes and 2 Power Requirements and Receptacle 3 Pinsetter 4 Power 4 Customer 4 brunswick 4 Tele-E-Foul Power 5 Power 5 Customer 5 brunswick 5 Junction Box for Ball Lift Control 6 Power 6 Customer 6 brunswick 6 Rotary Machine Power 7 Power 7 Customer 7 brunswick 7 brunswick 300/100 Lane Boss Power 8 Customer 8 brunswick 8 Lustre Kleen Custom Ball Conditioner Power 8 Power 8 Customer 8 Ball Booster power 9 Power 9 Customer 9 brunswick 9 Raceway with Pull 9 Customer 9 brunswick 9 Utility Grounded 10 Power 10 Customer 10 brunswick 10 Junction 11 Customer 11 brunswick 11 Bowling Lane Lighting 15

2 Bowling Equipment With A-2 Pinsetter Electrical Requirements 1 IntroductionThis brochure was compiled to tell the customer where he must provideelectrical power, receptacles, outlets and connections to accommodate thevarious pieces of brunswick 's Bowling equipment. In some instances, itsuggests a means of arriving at these locations. It should be noted, however,that these are merely SYSTEMS AND METHODS USED ARE THE COMPLETERESPONSIBILITY OF THE CUSTOMER AND HIS ELECTRICIAN ,AND MUST BE ACCEPTABLE BY LOCAL Bowling Equipment With A-2 Pinsetter Electrical RequirementsNotes and wiring for 115-230 Volts must be furnished and installed by thecustomer. All single phase equipment (specified for either 115V or230V) is designated for operation on a minimum sustained voltage ofeither 110V or 220V.

3 For A-2 pinsetters, nominal voltages of 115, 208and 230 are designed for operation of minimum sustained voltages of95, 175 and 190 local codes require conduit, raceways, wireways or other devices forwiring to, from, or between brunswick equipment, the installation andmaterial costs of these devices must be considered when designing yourbowling outlets for vending machines, fans clocks , housekeepingappliances, exterior lighting and signs, emergency lights, sump orejection pumps, , must be considered when designing your telephone company should be consulted in reference topublic telephone installation . Wall telephones are preferable overbooth low voltage communications systems from the control desk tothe Bowler's area is desirable for service and trouble low voltage communications system should be considered fromthe control desk to the pinsetter cost, design and installation of the manager's control desk is theresponsibility of the electrical utilities such as light, Tel-E-Scores, Automatic Scores,etc.

4 , should be controlled by switches installed in the control panel ofthis desk by the customer. A private house telephone, public addressand communications system should be installed here. Music may alsobe provisions for such items as cash terminal, control console,countertop advertising, sales display lighting and general utility outletsshould be other wiring, switching, etc., is the complete irresponsibility of thecustomer. Bowling Equipment With A-2 Pinsetter Electrical Requirements 3 Power Requirements and Receptacle Locations4 Bowling Equipment With A-2 Pinsetter Electrical RequirementsVOLTAGEOPERATINGCURRENTWIRE SIZESIZE OF BREAKER230 V10 Amps12 Amphere208 V10 Amps12 Amphere115 V20 Amps12 AmphereSpecial care is necessary to balance load on 3 phase supplies.

5 The wire andcircuit breaker supplies are based on the use of a separate circuit for eachpinsetter. If two pinsetter are connected on a single circuit, these sizes must beincreased ResponsibilityTo supply all necessary feeder wiring up to and including the ceiling mountedjunction box, with a flexible drop cord (rubber sheathed, 3 conductor, 12 gauge,type "S" service cord, or conduit, per local code) extending down from this boxto within 5'2" ( cm) above the playing surface of the lane. Brunswickwill supply the connector to be installed (at the end of the drop cord) by ResponsibilityTo supply connector for the end of the drop cord. (Hubbell #7313)Pinsetter Power OutletLocationCeiling mounted box with drop cord.

6 Reference Figures 1 & SupplyPinsetters will be supplied to operate on one of the following voltages, asdetermined by your utility company. All motors require 60 cycle, 1 phasesupplies. Bowling Equipment With A-2 Pinsetter Electrical Requirements 5 Tele-E-Foul Power OutletLocationSubway ball returns - the power outlet is to be located 18" ( cm) beyondthe foul line toward the pit and mounted on the right hand anchor strip beneaththe ball return cap. Reference Figures SupplyTel-E-Foul circuits must be separate from any other equipment as surges willsometimes cause a foul to be registered. There must be no more than 8 lanesper fused circuit, switched every 2 lanes at the operator's control desk. Powerdemand is 115V/230V, 60 cycle, 1 phase, 1 amp, AC, 20 W.

7 Grounded per pairof ResponsibilityCustomer is to supply and install junction box and all necessary feeder wiring toit. Customer is connect power cable to Tel-E-Foul (supplied by brunswick ) tojunction box before placement of ball return caps or ResponsibilityTo supply and install Tel-E-Foul unit and to supply power cable for Power Outlet InformationPower RequirementsCircuit RequirementsNOTE: Tel-E-Foul switched by two lanes at Control Desk6 Bowling Equipment With A-2 Pinsetter Electrical RequirementsJunction Box for Ball Lift Control BoxLocationOne junction box per each ball return. Reference Figures SupplyPower must be provided by the customer for the motor control box (whichservices the ball lift, hand dryer and pinfinder) 115V, 60 cycle, AC, 1/4 , 6amp, grounded or 208-230V, 60 cycle, AC, 1/4 , 4 amp, grounded.

8 Refer-ence Power Requirements and Receptacle ResponsibilityTo wire to, and connect junction box furnished by brunswick . Customer is alsoto install and connect wiring from junction box to motor control box; to installand connect wiring from motor control box to hand dryer, to connect wiring(supplied by brunswick ) from motor control box to ball lift ResponsibilityTo furnish junction box, to supply wiring from junction box to motor control box;to supply wiring and connector from motor control box to hand dryer; to supplywiring from control box to ball lift motor; to supply and install low voltagewiring from motor control box to automatic pinsetters. Bowling Equipment With A-2 Pinsetter Electrical Requirements 7 Rotary Machine Power Outlet (Wood Lanes Only)LocationIn an area so located to service complete lanes within a 75'0" (2, cm), 3conductor cable length, radius of the outlet.

9 Number of outlets furnisheddependent on size of installation . Suggested location in 5" ( cm) approachriser at each ball return terminal rack. Reference Figures Supply115V, AC, grounded power outlet. (Demand 15 amps, 1 , 60 cycle, 1phase.)Customer ResponsibilityTo supply box with a receptacle (Hubbell #5256 or equivalent) to receive aHubbell 3 prong connector (#5267); the number of boxes and receptacles toadequately service the size of Bowling Equipment With A-2 Pinsetter Electrical RequirementsBrunswick 300/100 Lane Boss Power OutletsLocationOne outlet at every other ball return in the approach riser. Reference Supply20 amp, 115v, 60 cycle, 1 phase, standard 3 prong grounded ResponsibilityTo supply and install box with 3 prong grounded outlet at every other Kleen Custom Ball Conditioner Power OutletLocationCentrally located in concourse supply30 amp, 230v, 60 cycle, 1 phase, 3 wire grounded ResponsibilityNone.

10 Bowling Equipment With A-2 Pinsetter Electrical Requirements 9 All 90 Degree bends of conduit to have 1'10" ( cm) minimum ResponsibilityTo supply and install all raceways and fittings with pull wires from controlstation to center of area of lanes serviced by raceways, terminating at the rearof the curtain ResponsibilityTo supply and install all 19 conductor cables in raceways, if required. One 19conductor cable is approximately 5/8" ( cm) Booster power OutletLocationCeiling mounted box with drop cord and receptacle to lane surface at centerline of each ball return; 5' 3-1/2" from rear of 83' 2" (pit end). ReferenceFigure SupplyMust correspond to pinsetter voltage, 230v - 5 Amps; 208v - 5 Amps; 115v -10 ResponsibilitySupply and install all necessary feeder wiring to and including ceiling mountedjunction box and drop cord (12 gauge, 3 wire type, "S" service cord, size.)