PREMIUM ROLLING TABLETOP GREENHOUSE BENCH WITH …

1 PREMIUM ROLLING TABLETOP . GREENHOUSE BENCH WITH. EBB & FLO TRAY. 2023 ROLLING TABLETOP GREENHOUSE BENCH with Ebb & Flo Trays All Rights Reserved. Reproduction *Actual BENCH may differ from example shown. is prohibited without permission. STK# DIMENSIONS. 116306T6X18 6' x 18'. Revision date: 1. Important Information READ BEFORE YOU BEGIN. Thank you for purchasing this PREMIUM GREENHOUSE BENCH . When properly assembled and maintained, this product will provide years of reliable service. These instructions include helpful hints and important information needed to safely assemble and properly maintain the BENCH . Please read these instructions before you begin. If you have any questions during the assembly, contact Customer Service at for assistance. SAFETY PRECAUTIONS ASSEMBLY PROCEDURE CARE AND MAINTENANCE. Wear eye protection. Following instructions as presented will help Proper care and maintenance is important. ensure proper assembly. Steps outlining Check the following items periodically to properly Wear gloves when handling metal pipes and assembly process are as follows: maintain your BENCH .

2 Frame components. 1. Verify all parts are included in shipment. Check connections and all fasteners to verify Use a portable GFCI (Ground Fault Circuit Notify customer service for questions or they remain tight. Interrupter) when working with power tools concerns. and cords. Do not climb or stand on frame at anytime. 2. Read these instructions and all additional REQUIRED TOOLS Verify all weight on BENCH top is evenly documentation included before you begin. distributed. The following list identifies the main tools needed 3. Gather tools. to assemble BENCH . Additional tools may be Promptly repair or replace all damaged parts needed. 4. For best results, assemble components on and frame members. a flat, level surface in the order presented in Marker and level (1' to 2') If BENCH is disassembled and moved, these instructions. inspect all parts and connections before Variable speed drill (cordless with extra 5. Read the care and maintenance information. reassembling and use. batteries works best).

3 Check anchor bolts and components to Small hammer and gloves UNPACK AND IDENTIFY PARTS ensure these are tight and in good repair. The following steps help ensure you have all Tighten or replace as needed. Rivet gun necessary parts before you begin. Inspect anti-tip brackets and fasteners to Ratchet and socket set 1. Unpack shipment contents and place where ensure these are tight and in good repair. 7/16", 9/16", and 3/4" wrenches you can easily inventory parts. Refer to the For replacement parts, call for Bill of Materials/Spec Sheets. assistance. Magnetic nut setter (3/8" x 2-9/16"). 2. Verify all parts listed on Bill of Materials/Spec Drill bit set with 5/32" bit to drill rivet holes in QUICK START GUIDE. Sheets are present. If anything is missing or BENCH corner caps you have questions, consult Pictorial Parts 3/8" drill bit to drill holes in concrete for 3/8" Guide and all diagrams for clarification, or For an overview of BENCH and connection details, wedge anchors contact Customer Service.

4 Consult the Quick Start Guide near the back of this guide. Hack saw or similar tool to cut metal NOTE: At this time, you do not need to open (optional) to miter top frame corners the plastic bags containing smaller parts such as fasteners or washers (if equipped). WARNING: Evenly distribute weight when in use. Never stand on BENCH . 2 Revision date: Important Information PICTORIAL GUIDE. WARNINGS AND CAUTIONS The following graphics and photos help identify different parts of your BENCH . (Some parts are not shown.). BENCH TO BE FULLY ASSEMBLED AND ANCHORED BEFORE. LOADING AND OPERATING TOP. BENCH IS NOT A TOY! NEVER CLIMB OR CRAWL ON BENCH . STAY CLEAR OF BENCH WHEN ROLLING TOP AND DURING. OPERATION. ENSURE PROPER CLEARANCES AROUND BENCH TO AVOID. INJURY DURING OPERATION. FALB10B FAG102B FA4482B 113153 Rivet BENCH IS METAL AND WILL CONDUCT ELECTRICITY! NEVER 1/4" Nut 1/4" x 3/4" Bolt Tek Screw ALLOW EXTENSION CORDS TO DRAPE OVER TOP OR FRAME. NEVER ALLOW ELECTRICAL APPLIANCES (FANS, HEATERS, ETC.)

5 OR ELECTRIC TOOLS TO OPERATE ON BENCH TOP. NEVER ATTACH ELECTRIC LIGHT FIXTURES TO BENCH FRAME. OR ROLLING TOP. FAG359B FALB04B FAME51B & 108553 Truss NEVER LOAD AND OPERATE ROLLING TOP WITHOUT 3/8" x 2" 3/8" Nut FAME08B Head Screw ANCHORING MAIN BENCH FRAME TO BUILDING OR FLOOR. Washers DO NOT OVERLOAD BENCH TOP. EVENLY DISTRIBUTE WEIGHT OVER BENCH TOP WHEN IN. OPERATION TO PREVENT TIPPING OR INJURY. NEVER OPERATE ROLLING TOP WITHOUT INSTALLING ANTI- TIP BRACKETS. INSPECT BENCH FREQUENTLY TO IDENTIFY LOOSE BOLTS, CONNECTIONS, AND BRACKETS. TIGHTEN OR REPLACE AS. NEEDED. FAH320B Carriage Bolt & 112815 Poly 116218 &. FALB32B Nut Corners for 115857 Cap KEEP CHILDREN AWAY FROM BENCH AT ALL TIMES! BENCH top. ASSEMBLY NOTE: Install Tek screws using a clutched drill driver running approximately 750 RPM while applying approximately 50 lbs of force. Do not use an impact driver! Revision date: 3. Leg Assembly 1 LEG ASSEMBLY ASSEMBLE LEG ASSEMBLIES. 1. Slide one end of the cross member through the lock system of leg until Before populating the trays and using the BENCH , complete this section to flush.

6 Insert one carriage bolt through cross member and leg, add nut adjust height and level BENCH . and tighten to secure bolt. 2. Attach second leg to the leg assembly using carriage bolt and nut. 1. Use an adjustable wrench or pliers to turn/adjust the threaded mounting 3. Repeat steps to assemble all remaining leg assemblies needed for your bolts (A) to desired height. system. ATTENTION: DO NOT EXCEED 39 INCHES FROM GROUND LEVEL. TO TOP OF GROWING TRAY SURFACE. 2. Repeat the steps as needed for all other adjustable bolts until frame is 1/4" Hex Nut (FALB30). level and at the height needed. 1/4" x 1-1/2". Carriage Bolt 3. Return to each lock nut and tighten. (117342). " - 42". Adjustable BENCH Height Use leveling bolts to adjust 25" Tray Maximum 13 1/16". Tray On-Center A height of BENCH /tray. A Roll Position Position " - 39". Adjustable Tray Height 1/4" x 1-1/2". Carriage Bolt (117342) 1/4" Hex Nut (FALB30). 4 Revision date: Main Frame Assembly 2 MAIN FRAME ASSEMBLY. ATTENTION: ASSEMBLE FRAME IN LOCATION WHERE YOU WILL ANCHOR.

7 IT TO FLOOR. DO NOT ATTEMPT TO MOVE ASSEMBLED BENCH . Diagrams on this page show one way to assemble the main frame. Brackets (115918) used to anchor frame to concrete floor, attached to end leg assemblies, are shown. Install these now or wait until BENCH is fully assembled and positioned in the desired location. Additional assistants are needed for easier assembly. 1. Consult Quick Start section diagrams for connection details and required parts. 2. Connect long side tubes according to Side Profile diagram in Quick Start section. Secure each side tube splice using one (1) S125P006 tube and four (4). FA4482B Tek screws. ATTENTION: Install long side rail tubes flush with end of brackets. See diagram A (lower-right corner). Longer benches have side tube assemblies constructed using multiple, long pipes. Add these pipes and splice connectors as BENCH frame is assembled. 3. Using 115849 brackets, 1/4" fasteners, and the leg assemblies, LEG ASSEMBLY. construct main frame. NOTE: Space leg supports according to Side Profile diagram in Quick Start section.

8 4. Continue with next procedure. BRACKETS. SIDE TUBE (115849). See close-up A. See Side Profile diagram for tube identification and quantities. Install tube flush with A bracket. Revision date: 5. Cross Support Assembly 3 CROSS SUPPORT ASSEMBLY Gather Parts: 115851 plastic caps Cross supports allow user to level BENCH top as needed to achieve desired results. Complete these steps to 115852 1/2" x 6" threaded bolts assemble and install all BENCH frame cross supports with leveling hardware. 116270 square tubes drilled with 1. To assemble leveling bolts, slide a 0706P0005 insert onto a 1/2" bolt (115852) and slide that assembly holes for bolt stops through mounting hole of cross support. 0706P0005 1/2" insert Plastic Cap FAME53B 1/2" flat washer FALB08B 1/2" nut 115852 116270 Cross Support 0706P0005 Insert FALB08B Nuts 1/2" Washer (FAME53B). Top of leg assembly of main frame. 1/2" washer 2. Add one 1/2" nut and tighten to secure bolt to support tube. (See photo next page.) each side. 3. Thread another 1/2" nut onto bolt up to first nut.

9 4. Repeat to assemble and install all leveling bolts. See Quick Start section diagrams. 5. Next, slide a 1/2" washer onto each bolt and insert ends of leveling bolts into top of leg assemblies of main frame as shown. 6. Continue with next procedure. *Actual BENCH length may differ from example shown. 6 Revision date: Level Cross Supports 4 LEVEL CROSS SUPPORTS. For easier access to adjusting bolts, level all cross supports now before setting assembled top on lower main frame. Complete these steps. 1. With BENCH frame assembly in desired location, adjust all leveler nuts so cross support is in its lowest position. 2. Using a level and 3/4" wrench, level each cross support. NOTE: For end-to-end adjustment, temporarily place a straight edge (such as an aluminum side rail) on cross supports to check for uniform height. See dashed line on diagram to the right. For long benches, stretch a string line end-to-end and adjust cross tubes as needed. Adjust this nut to 3. Continue with ROLLING pipe assembly.

10 Level cross support. Level *Actual BENCH length may differ from example shown. Revision date: 7. Assemble ROLLING Pipes 5 ASSEMBLE ROLLING PIPES. ROLLING pipe assemblies allow BENCH top to move on main support frame once BENCH is fully assembled. These assemblies typically consist of multiple round pipes connected and secured at each joint. Consult diagrams and information below and assemble each ROLLING pipe. Complete these steps: 1. Confirm correct pipes are selected. There are two identical ROLLING pipe assemblies. 2. Connect first two pipes and secure joint using one (1) 108553 truss head screw. Assemble on frame if desired. ATTENTION: If you purchased crank kit 116861 for your BENCH , review the instructions included with that kit now. Install the lock collars included with that kit. Then, return to these instructions and the next step. If you did not purchase the crank kit, continue with the next step. 131P066. 3. Add next pipe (if needed) and secure joint using a 108553 truss head screw.