Product Bulletin D and DA Valves August 2017 Fisher D and ...

1 D and DA control ValvesFisher D and DA single port, high pressure Valves arewidely used in oil and gas production industries. Thesevalves are especially useful for either throttling oron/off control of liquids or gases which are gritty,sticky, or which have a tendency to build up on internalvalve parts. The DA valve is also useful in angle pipingor other applications where a self draining valve otherwise noted, all NACE references are toNACE MR0175 Heavy Duty Construction Massive guiding (figure1) positively aligns the valve plug in the seat ring forhigh pressure drop applications. The screwed inseat ring completely encloses the seat ring Easy Maintenance Screwed bonnet/body jointallows repair or maintenance with a minimum Severe Service Capability Valve is available withVTC (ceramic) trim for service in very erosiveapplications. The valve plug is also available with atungsten carbide tip and the seat ring can be fittedwith a full bore tungsten carbide insert for Meets Variety of Specifications Valve body and endconnection constructions are available for API aswell as ASME 1 Fisher D Valve with 657 Actuatorn NACE Trim Standard NACE trim and boltingmaterials are standard for all applications.

2 Thesematerials comply with the requirements of NACEMR0175 and DA ValvesD100039X012 Product :DAugust 2017D and DA ValvesD100039X012 Product :DAugust 2017 2 SpecificationsAvailable ConfigurationsD: Globe valve with screwed on bonnet, unbalancedpost guided valve plug, screwed in seat ring, metalseat construction, and push down to close valve plugactionDA: Same as D valve except in angle configuration(figure 1)Valve Sizes and End Connections(1)See table 1 Maximum Inlet Pressures and Temperatures(1)(2)See table 2 Maximum Allowable Pressure Drops(2)Flow up: Capable of full rated pressure dropsFlow down: See table 3 for pressure drop limits forceramic trimShutoff Classification per ANSI/FCI 70 2and IEC 60534 4 Standard: Class IV leakageOptional: Class VMaterial Temperature Capabilities-46 to 232_C (-50 to 450_F)Construction MaterialsBody, Bonnet, and Trim: See table 4 Packing:Standard: JSingle or Jdouble PTFE V ring packingfor pressure serviceOptional: Double PTFE/CompositionStandard Gaskets: S31600 (316 SST)Flow CharacteristicEqual percentageFlow Direction (see figure 1)D: Flow up (through seat ring and past valve plug)DA: JFlow up (through seat ring and past valve plug)or Jflow down (past valve plug and through seatring)Flow Coefficients and Noise Level PredictionSee table 5 or Fisher Catalog 12 Port, Yoke Boss, Stem Diameters, and Rated TravelsSee table 6 Approximate WeightsNPS 1: 34 kg (75 pounds)NPS 2: 45 kg (100 pounds)OptionsJLubricator/isolating valve JVTC (ceramic) Trimwith equal percentage characteristic (not availablewith Micro Flute trim) JTungsten Carbide trim (notavailable with Micro Flute trim)1.

3 EN (or other) ratings and end connections can usually be supplied; consult your Emerson sales office or Local Business The pressure/temperature limits in this Bulletin and in any applicable standard limitations should not be Sizes, Port Diameters, and End Connections Inlet Pressures and Temperatures Down Pressure Drop Limits Ceramic Trim Only for Standard Trim Constructions Coefficient (Cv at Maximum Valve Plug Travel) , Yoke Boss, Stem Diameters,and Rated Travel Specifications Information and DA ValvesD100039X012 Product :DAugust 2017 3 Table 1. Valve Sizes, Port Diameters, and End ConnectionsVALVESIZE,NPSPORT DIAMETER(INCHES)SCREWED VALVE BODIESFLANGED VALVE BODIES3600 psi6000 psi9000 psi(WCC SteelDA Only)10,000 psi(Except WCCS teel DA)ASMEAPICL150throughCL600CL900 andCL1500CL250010,000 A and , , , (1)X XXX , , , , 1, `X' indicates available 2. Rated Inlet Pressures and TemperaturesVALVE SIZE,NPSTYPEPRESSURE RATING OR COLDWORKING PRESSURE LIMITPRESSURE(1)TEMPERATURE barpsi_C_F1 or 2 ScrewedCL900 and 15002592363750342538232100450CL250043139 46250571038232100450900062190003810010,0 0068910,000381001 or and 15002592363750342538232100450CL250043139 46250571038232100450 API 10,000689689 Spec A 10,000 Spec C 10,0001211212502501.

4 LCC steel body per ASME except C5 steel for all API 3. Flow Down Pressure Drop Limits Ceramic Trim OnlyVALVE SIZE,NPSSEAT RING DIAMETER, mm (INCHES) ( ) ( ) ( ) ( ) (1) ( )Pressure Drop, bar1414414414193 2689689689462262165 Pressure Drop, psi16000600060002800 210,00010,00010,000670038002400 Table 4. Materials for Standard Trim ConstructionsVALVE MATERIALBONNET MATERIALPLUG AND SEAT RINGVALVE STEMLCCLF2S31600 (316 stainless steel)hard faced with CoCr A (Alloy 6)S20910 WCCD and DA ValvesD100039X012 Product :DAugust 2017 4 Table 5. Flow Coefficient (Cv at Maximum Valve Plug Travel)VALVE SIZE,NPSPORT DIAMETER,mm (INCHES)EQUAL PERCENTAGE DEQUAL PERCENTAGE DAFlow UpFlow ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) (1) ( ) 6. Port, Yoke Boss, Stem Diameters, and Rated Travel Specifications in mm (Inches)VALVESIZE,NPSPORTDIAMETERSTANDAR DOPTIONALYoke BossDiameterStemDiameterRatedTravelYoke ( ) ( ) ( ) ( )54 (2 1/8) (3/8) ( )71 (2 13/16) (1/2) ( )90 (3 9/16) (3/4) ( ) ( ) ( ) ( ) ( ) (1) ( )71 (2 13/16) (1/2) ( )90 (3 9/16) (3/4) ( )Figure 1.

5 Typical ConstructionsW0540-2W0938 2D and DA ValvesD100039X012 Product :DAugust 2017 5 InstallationValve orientation of the D and DA does not affectoperation, but to facilitate changing trim parts, thevalve stem should be vertical with the actuator abovethe valve. Proper flow direction is indicated by thearrow on the are shown in figures 2 and InformationWhen ordering, specify:Application1. Type of applicationa. Throttling or on offb. Reducing or relief2. Controlled fluid (include chemical analysis of fluid, ifpossible)3. Specific gravity of controlled fluid4. Fluid temperature5. Range of flowing inlet pressure6. Pressure dropsa. Range of flowing pressure dropsb. Maximum at shutoff7. Flow ratesa. Minimum controlled flowb. Normal flowc. Maximum flow8. Maximum permissible noise level, if critical9. Shutoff classification required10. Line size and scheduleValveRefer to the specifications. Review the description foreach specification.

6 Indicate the desired choicewhenever there is a selection (J) to be made. Alwaysindicate the valve body design being ordered asidentified in the available configuration and AccessoriesRefer to separate bulletins covering actuators andaccessories for ordering and DA ValvesD100039X012 Product :DAugust 2017 6 Table 7. Fisher D DimensionsFLANGEDVALVESIZE,NPSASMED--All RatingsCL150CL300CL600A RaisedFaceGAGAGStem SizeRaisedFaceRing TypeJointRaisedFaceRing (3/8) (1/2) (3/4)mm120646219232462322324617319217922 6770267 7028628970 8. Fisher D DimensionsFLANGEDVALVESIZE,NPSASMEAPID-- All RatingsCL900 and 1500CL250010,000 SizeRaisedFaceRing TypeJointRaisedFaceRing TypeJointSpec ASpec (3/8) (1/2) (3/4)mm12542544630830854 1731921792308311703913948336436083 (1) (1) (1) Not applicable for 10,000 lb. 9. Fisher D DimensionsSCREWEDVALVE SIZE,NPS3600 psi6000 psi and9000 psiD--All RatingsStem (3/8) (1/2) (3/4)mm1(1)16846197541721921782229702678 3 216211 Inches1(1) For 3600 psi and 6000 psi 2.

7 Fisher D Dimensions (also see tables 7, 8, and 9)AJ1318 EA1888 1 MATCH LINEFOR ACTUATORDGAA2D and DA ValvesD100039X012 Product :DAugust 2017 7 Table 10. Fisher DA DimensionsFLANGEDVALVESIZE,NPSA and GD--All RatingsASMECL300CL600 Stem SizeRaisedFaceRing TypeJointRaisedFaceRing (3/8) (1/2) (3/4)mm110911611611613515414121551641651 67 11. Fisher DA DimensionsFLANGEDVALVESIZE,NPSA and GD--All RatingsASMEAPICL900 and 1500CL250010,000 SizeRaisedFaceRing TypeJointRaisedFaceRing TypeJointSpec ASpec (3/8) (1/2) (3/4)mm1127127154154 1351541412178179195197182180 12. Fisher DA DimensionsSCREWEDVALVESIZE,NPS3600 psi6000 psi and9000 psiD--All RatingsStem (3/8) (1/2) (3/4)mm1(1)76898910213315214021021241141 30 162157 Inches1(1) For 3600 psi and 6000 psi 3. Fisher DA Dimensions (also see tables 10, 11, and 12)MATCH LINEFOR ACTUATORDGAAJ1318 EA1887 1D and DA ValvesD100039X012 Product :DAugust 2017 8 Emerson Automation Solutions Marshalltown, Iowa 50158 USAS orocaba, 18087 BrazilCernay 68700 FranceDubai, United Arab EmiratesSingapore 128461 contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are notto be construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or applicability.

8 All sales aregoverned by our terms and conditions, which are available upon request. We reserve the right to modify or improve the designs or specifications of suchproducts at any time without 1991, 2017 Fisher Controls International LLC. All rights is a mark owned by one of the companies in the Emerson Automation Solutions business unit of Emerson Electric Co. Emerson Automation Solutions,Emerson, and the Emerson logo are trademarks and service marks of Emerson Electric Co. All other marks are the property of their respective Emerson, Emerson Automation Solutions, nor any of their affiliated entities assumes responsibility for the selection, use or maintenanceof any Product . Responsibility for proper selection, use, and maintenance of any Product remains solely with the purchaser and end user.