Q1018 Series - Qatofin

1 Q1018 SeriesLinear Low Density Polyethylene (LLDPE) DESCRIPTION AND USELotr ne Q1018 Series are Linear Low Density Polyethylene resins produced in a gas phase reactor using butene(C4) are designed for blown film applications and can be used in pure form as well as blended with other PEresins, such as LDPE or HDPE and mPE resins for mono extrusion or co-extrusion process to modify film ne Q1018 Series are suited for many applications in the field of consumer, agricultural, industrial, foodor hygiene packaging, for example: collation shrink, liners, FFS bags, heavy duty sacks, refuse, tunnel films,mulching PACKAGEPRODUCTSLIP (ERUCAMIDE) (PPM)ANTIBLOCK (PPM)THERMAL STABILIZERSQ1018 NnonoYes (blown film)Q1018H1500 3200 Yes (blown film)Values indicated are target values. Actual values might differ from batch to PROPERTIESVALUEUNITTEST METHODD ensity* @ 23 C g/cm3 ASTM D-792 Melt Flow Index (190 *C kg) D-1238 Crystalline Melting Point122 CInternalVicat Softening Point100 CASTM D-1525 (A120)(* Density of base resin)FILM PROPERTIESVALUE (*)UNIT TEST METHODT ensile Strength @ Yield MD/ TD11/11M PaASTM D-882 Tensile Strength @ Break MD/ TD38/33M PaASTM D-882 Elongation @ Break MD/ TD800/850%ASTM D-882 Secant modulus @ 1% MD/ TD215/245M PaASTM D-882 Impact Strength, F 50150gASTM D-1709 Tear resistance MD/ TD280/48070/120gN/mmASTM D- 1922 Haze11%ASTM D-1003 Gloss (@ 45 ) 60-ASTM D-2457(The above properties are measured on a blown film under following parameters: Screw 45 mm, L/D 30, die gap mm, output 30 kg/hr, mass temperature 210 C, thickness 40 m and BUR :1)PROCESSINGE xtrusion temperatures: 180-220 CMelt temperature 200 CBlow-up ratio: 2:1 to 3:1 Die gap.

2 > mmLotr ne Q1018 Series can be processed at high output rates with moderate extrusion pressure, good bubblestability and gauge control on blown film lines designed for ne Q1018 Series can be blended with LDPE and other PE resins in order to improve film properties orprocess ability on conventional mono or co extrusion machines. HANDLING & STORAGEP olyethylene products should be stored in their original packaging or in clean appropriate products should be stored in a dry and well-ventilated area and should not be exposed to direct sunlight and/or heat in any form since this may adversely affect their a general rule, our products should not be stored for more than three months from receipt normal conditions Lotr ne products do not present a toxic hazard through skin contact or detailed information please refer to the Safety Data Sheet. FOOD CONTACT & REACHLotr ne polyethylene products manufactured by Qatofin Company Ltd ( Qatofin ) comply with US, EU and other food contact legislations.

3 Limitations may apply. All Qatofin Lotr ne products are complying with REACH Regulation 1907/2006/EC. The aims of this regulation are to improve the protection of human health and the environment through better and earlier identification of the intrinsic properties of chemical substances. Please contact your Muntajat representative for detailed compliance SUITABLE FOR PHARMACEUTICAL OR MEDICAL APPLICATIONS TECHNICAL DISCLAIMERThe values reported in this technical data sheet are the results of tests carried out in accordance with standard test procedures in a laboratory environment. Actual properties may vary depending on batch and extrusion conditions. Therefore, these values should not be used for specification using this product, the user is advised and cautioned to make its own determination and assessment of the safety and suitability of the product for the specific use in question, and is further advised against relying on the information contained herein as it may relate to any specific use or is the ultimate responsibility of the user to ensure that the product is suitable for, and the information is applicable to, the user s specific application.

4 Qatofin does not make, and expressly disclaims, all warranties, including warranties of merchantability or fitness for a particular purpose, regardless of whether oral or written, expressed or implied, or allegedly arising from any usage of any trade or from any course of dealing, in connection with the use of the information contained herein or the product user expressly assumes all risks and liabilities, whether based in contract, tort or otherwise, in connection with the use of the information contained herein or the product itself. Trademarks may not be used in any manner other than expressly authorized in a written agreement and no trademark or license rights of any kind are granted hereunder, by implication or Company LimitedP. O. Box 50155, Mesaieed, State of Qatar Tel : (+974) 4477 7111, Fax : (+974) 4477 1346 by QAPCOQ2018 Series Linear Low Density Polyethylene (LLDPE) DEScriPtion anD USELotr ne Q2018 Series are Linear Low Density Polyethylene resins produced in a gas phase reactor using butene (C4) co-monomer.

5 They are designed for blown film applications and can be used in pure form as well as blended with other PE resins, such as LDPE or HDPE and mPE resins for mono extrusion or co-extrusion process to modify film ne Q2018 Series are suited for many applications in the field of consumer, industrial, food or hygiene packaging such as freezer film, bread bags, shoppers and bags as well as lamination film and multilayer packaging PackagEProductSlip (Erucamide) (ppm)antiblock (ppm)thermal StabilizersQ2018nnonoYes (blown film)Q2018H15003200 Yes (blown film)Q2018cnonoYes (cast film)values indicated are target values. actual values might differ from batch to ProPErtiESvaLUEU nittESt MEtHoDDensity* D-792 Melt Flow index (190 c kg) D-1238crystalline Melting Point121 cinternalvicat Softening Point100 caStM D-1525 (a120)(* Density of base resin)FiLM ProPErtiESvaLUE (*)UnittESt MEtHoDtensile Strength @ Yield MD/ tD11/11M PaaStM D-882tensile Strength @ Break MD/ tD35/32M PaaStM D-882 Elongation @ Break MD/ tD850/900%aStM D-882 Secant modulus @ 1% MD/ tD215/245M PaaStM D-882impact Strength, F 50130gaStM D-1709tear resistance MD/ tD220/42055/105gn/mmaStM D- 1922 Haze14%aStM D-1003gloss (@ 45 ) 55-aStM D-2457(The above properties are measured on a blown film under following parameters: Screw 45 mm, L/D 30, die gap mm, output 30 kg/hr, mass temperature 210 C, thickness 40 m and BUR :1)Processing:Extrusion temperatures: 170-210 CMelt temperature 190 *C Blow-up ratio: 2:1 to 3:1 Die gap.

6 > mmLotr ne Q2018 Series can be processed at high output rates with moderate extrusion pressure, good bubble stability and gauge control on blown film lines designed for LLDPE. Q2018 Series can be blended with LDPE and other PE resins in order to improve film properties or processability on conventional mono or co extrusion & StoragEPolyethylene products should be stored in their original packaging or in clean appropriate products should be stored in a dry and well-ventilated area and should not be exposed to direct sunlight and/or heat in any form since this may adversely affect their a general rule, our products should not be stored for more than three months from receipt normal conditions Lotr ne products do not present a toxic hazard through skin contact or detailed information please refer to the Safety Data contact & rEacHLotr ne polyethylene products manufactured by Qatofin Company Ltd ( Qatofin ) comply with US, EU and other food contact legislations.

7 Limitations may apply. All Qatofin Lotr ne products are complying with REACH Regulation 1907/2006/EC. The aims of this regulation are to improve the protection of human health and the environment through better and earlier identification of the intrinsic properties of chemical substances. Please contact your Muntajat representative for detailed compliance SUITABLE FOR PHARMACEUTICAL OR MEDICAL APPLICATIONStEcHnicaL DiScLaiMErThe values reported in this technical data sheet are the results of tests carried out in accordance with standard test procedures in a laboratory environment. Actual properties may vary depending on batch and extrusion conditions. Therefore, these values should not be used for specification using this product, the user is advised and cautioned to make its own determination and assessment of the safety and suitability of the product for the specific use in question, and is further advised against relying on the information contained herein as it may relate to any specific use or is the ultimate responsibility of the user to ensure that the product is suitable for, and the information is applicable to, the user s specific application.

8 Qatofin does not make, and expressly disclaims, all warranties, including warranties of merchantability or fitness for a particular purpose, regardless of whether oral or written, expressed or implied, or allegedly arising from any usage of any trade or from any course of dealing, in connection with the use of the information contained herein or the product user expressly assumes all risks and liabilities, whether based in contract, tort or otherwise, in connection with the use of the information contained herein or the product itself. Trademarks may not be used in any manner other than expressly authorized in a written agreement and no trademark or license rights of any kind are granted hereunder, by implication or Company LimitedP. o. Box 50155, Mesaieed, State of Qatar Tel : (+974) 4477 7111, Fax : (+974) 4477 1346 by QAPCOQ2018 CLinear Low Density Polyethylene (LLDPE) DEsCriPtion anD UsELotr ne Q2018C is a Linear Low Density Polyethylene resin produced in a gas phase reactor us-ing butene (C4) co-monomer.

9 Lotr ne Q2018C can be processed at optimal output rates with moderate extrusion pressure, good web stability and gauge control on cast film machines designed for LLDPE. Lotr ne Q2018C can advantageously be blended with LDPE or other PE resins used in cast film mono extrusion or co-extrusion to improve film ne Q2018C is for melt index cast stretch film market. It is suited for many applications in the field of consumer, industrial, food or hygiene packaging as well as non-packaging applications like agricultural films mulching PaCkagEProductslip (Erucamide)antiblockProcessing aidthermal stabilizersQ2018 CnononoYes (cast film)CharaCtEristiCsPropertyMethodUnitva lueDensity (*)astM D-792g/cm Flow rate (190 kg)astM D-1238g/10 temperatureinternal C121vicat temperatureastM D-1525 (a120) C100(* density of base resin)Cast FiLM ProPErtiEsPropertiesMethodUnitvalue (*)tensile strength at Yield MD/tDastM D-882M / strength at Break MD/tDastM D-882M Pa37 / 23 Elongation at Break MD/tDastM D-882%330 / 670 Elmendorf tear resistance MD/tDastM D- 1922n/mm12 / 193secant modulus at 1% MD/tDastM D-882M Pa165 / 170 Dart test, F50astM D-1709g35 Puncture forceastM D5748n25 Puncture energyastM D-1003% @ 45 astM D245792 The above properties are measured 20 m films produced on a cast film line under the following parameters: 30 mm screw, L/D = 30:1, die length = 600 mm, die gap = mm, line speed = 50 m/min, temperature setting = 180-230 C.

10 Melt tempera-ture 250 C. Chill roll temperature: 25 ne Q2018C is typically extruded at a melt temperatures between 220 and 250 ne Q2018C can be cast in the following conditions on machine designed for LLDPE: Extrusion temperature: 180 to 270 C Line speed: > 400 m/min Die gap: > mmAn excellent blending ability of LOTR NE Q2018C with LDPE and HDPE and mLLDPE was & storagEPolyethylene products should be stored in their original packaging or in clean appropriate products should be stored in a dry and well-ventilated area and should not be exposed to direct sunlight and/or heat in any form since this may adversely affect their a general rule, our products should not be stored for more than three months from receipt normal conditions Lotr ne products do not present a toxic hazard through skin contact or detailed information please refer to the Safety Data Sheet. FooD ContaCt & rEaChLotr ne polyethylene products manufactured by Qatofin Company Ltd ( Qatofin ) comply with US, EU and other food contact legislations.