Example: biology

Qm300 ID 30024335 - SIGMA Equipment

MACHINE IDENTIFICATION. Each Lantech Inc. Stretch Wrap Machine is identified with a serial number plate and decal. The plate is located at the base of the upright. The decal is located on the panel door. If service should become necessary, you will need the information found on the serial number decal. Distributor: Write in the local Lantech distributor name and contact information here: Distributor Name: _____. Distributor Address: _____. _____. _____. _____. Distributor Phone: _____. Distributor Contact: _____. Q- Series Operator & Maintenance Manual Table of Contents Introduction Safety Information Warranty Information Getting Help Machine Description & General Information Machine Layout Technical Specifications & Operating Requirements Description of Major Subassemblies, Components & Control Panels Description of Operation Installation instructions Preparation For Installation Mechanical Installation Machine Setup "A" (Machines shipped with base and upright bolted together).

2.4 Description of Operation 3.0 Installation Instructions 3.1 Preparation For Installation 3.2 Mechanical Installation 3.2.1 Machine Setup "A" (Machines shipped with base and upright bolted together) ... Micro-Controller Logic MACHINE SIZE 105"L x 67"W x 93"H (std) 105"L x 154"W x 93"H (opt Dual Turntable) Shipping weight - 1580 lbs. OPTIONS

Tags:

  Controller, Operations, Instructions, Logic, Logic controller

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Other abuse

Transcription of Qm300 ID 30024335 - SIGMA Equipment

1 MACHINE IDENTIFICATION. Each Lantech Inc. Stretch Wrap Machine is identified with a serial number plate and decal. The plate is located at the base of the upright. The decal is located on the panel door. If service should become necessary, you will need the information found on the serial number decal. Distributor: Write in the local Lantech distributor name and contact information here: Distributor Name: _____. Distributor Address: _____. _____. _____. _____. Distributor Phone: _____. Distributor Contact: _____. Q- Series Operator & Maintenance Manual Table of Contents Introduction Safety Information Warranty Information Getting Help Machine Description & General Information Machine Layout Technical Specifications & Operating Requirements Description of Major Subassemblies, Components & Control Panels Description of Operation Installation instructions Preparation For Installation Mechanical Installation Machine Setup "A" (Machines shipped with base and upright bolted together).

2 Machine Setup "B" (Machines shipped with separated base and upright). Electrical Installation Operator instructions Applying Electrical Power Loading The Turntable Typical Sequence of Operation Membrane Panel Controls Machine Operation Initial Start-up Procedure Film Loading Normal Operation Band Maintenance Procedures Preventive Maintenance Corrective Maintenance Standard Adjustments Technical Adjustments Troubleshooting/ Guide Appendix Appendix A Glossary Of Terms Appendix B Recommended Spare Parts Appendix C Drawings & Parts List INTRODUCTION. IMPORTANT SAFETY INFORMATION. Any power Equipment can be unsafe or operate inadequately if it is not properly installed, operated by trained personnel, and periodically maintained. Procedures recommended in this manual will provide safe operation and reliable performance.

3 Some service procedures in this manual may require special tools. These special tools should be used when recommended. We include DANGERS, WARNINGS, CAUTIONS, and NOTES to alert you to specific procedures which insure safety for personnel and satisfactory operation. These words have special meaning which are described below: DANGER: indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING: indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. CAUTION: indicates a potentially hazardous situation which, if not avoided, may result in a minor or moderate injury. NOTE: Indicates a point of particular interest which can afford more efficient operation.

4 It is important to know that this manual contains various precautions which should be carefully read. It is important to understand that these precautions are not exhaustive. Lantech Inc. can not possibly know, evaluate, or advise the various trades in all tasks which might be performed. Because of this, Lantech Inc. has not undertaken such tasks. Accordingly, anyone who installs, trains, operates, or services a Lantech Inc. Stretch Wrap Machine must first satisfy himself/herself as to the safety of a precautionary procedure. Lantech Q-Series Section Introduction Page 1. SAFETY OF OPERATION. Start operation of the machine only after all required housekeeping / maintenance tasks are safely completed. Ensure the safety of all personnel in the immediate area before starting the machine.

5 Caution: Cease operation of the machine instantly if any of the following are observed: unusually noisy operation. irregular vibrations. current consumption greater than the rated current of motor. Determine the cause of the problem and take proper corrective action . Resumption of operating mode is only permissible if defects and / or damages in the machine have been properly corrected. EMERGENCY STOP. The machine is supplied with an emergency stop mounted on the electrical control panel. Before starting the Q-Series machine, you should be acquainted with the emergency stop procedure and the location of the emergency stop pushbutton. Do not use the emergency stop for unauthorized purposes. CAUTION: When working on the machine, you should always press the Figure E-Stop Pushbutton emergency stop and unplug the machine from it's power source.

6 Page 2 Section Introduction Lantech Q-Series GUARDING. All dangerous machine parts (chains, belts, sprockets, etc.) are covered with guarding. NOTE: If the guards are removed for maintenance or repairs, they must always be replaced to the proper position and secured, before operating the machine. TOOLS/OBJECTS ELECTRICITY. Proceed with care when preforming Before starting the machine, ensure that electrical troubleshooting or all tools and other objects are removed, maintenance on the machine. otherwise damage can occur to the machine or injury to persons in the Authorized and qualified personnel only immediate area of the machine. may carry out activities on the electrical system, with due observance of the safety requirements.

7 Improper use of electrical Equipment can lead to fatal accidents, serious bodily harm or considerable damage to the system. During operation of electric motors and / or Equipment , certain parts of the Equipment will hold a dangerous charge, possibly even when switched off! Work on electrical Equipment should only be carried out by qualified personnel. Prior to working on any electrical Equipment it must be disconnected and grounded by a qualified electrician. Lantech Q-Series Section Introduction Page 3. COMPRESSED AIR. Ensure fittings and air hoses are in good condition before using them. Before disconnecting an air hose, close WALKING ON CONVEYORS. supply valve and ensure pressure is Walking on conveyors, if this CAUTION: YOU released machine is so equipped, while the SHOULD NEVER system is running, is strictly POINT A forbidden, conveyors can start CAUTION: You should COMPRESSED moving unexpectedly.

8 Never point a compressed AIR NOZZLE AT air nozzle at anyone. Never ANYONE. use an air hose to blow Warning: Walking on dust off clothes. gravity conveyors is always NEVER USE AN strictly forbidden !! AIR HOSE TO. BLOW DUST. OFF CLOTHES. CHANGES / MODIFICATIONS. The manufacturer is not responsible for INTENDED PURPOSE OF. all modifications and adaptations MACHINE. which can influence the safety of the WARNING: BE machine operation. The intended purpose of this machine PREPARED FOR is to unitize for additional handling, Those who carry out the modifications stable, non-hazardous product with THOSE or adaptations are fully responsible. stretch material to contain the UNEXPECTED product. MOVEMENTS !! This machine is not intended for use HORSEPLAY to unitize hazardous materials or be operated in a hazardous or explosive Horseplay or frivolous behavior with or environment.

9 WARNING: in the area of a working Q-Series WALKING ON system can be dangerous and cause injury. Playing is never allowed. GRAVITY. CONVEYORS IS. ALWAYS. STRICTLY. FORBIDDEN !! Page 4 Section Introduction Lantech Q-Series WARRANTY. Seller warrants the products manufactured by it, and sold pursuant to this contract to be free from defects in material and workmanship for a period of three years from delivery date, and under normal use and service. Seller neither assumes nor authorizes any person to assume for it any obligation in connection with sale of seller's Equipment . This warranty shall not apply to any other Equipment which has been repaired or altered by unauthorized personnel in any way so as to, in the judgment of Seller, affect serviceability, or which has been subject to misuse, negligence, accident, or to Equipment made by Seller which has been operated in a manner contrary to Seller's instructions .

10 EXCEPT TO THE EXTENT WARRANTED ABOVE, SELLER MAKES. NO OTHER WARRANTY OR REPRESENTATION OF ANY KIND. WHATSOEVER WITH RESPECT TO THE Equipment AND/OR. GOODS CONTRACTED HEREBY, EXPRESS, OR IMPLIED; AND ALL. IMPLIED WARRANTIES OR MERCHANTABILITY AND FITNESS FOR. PARTICULAR PURPOSE WHICH EXCEED THE AFFORESTATED. OBLIGATION ARE HEREBY DISCLAIMED BY SELLER AND. EXCLUDED FROM THE AGREEMENT. BUYER'S EXCLUSIVE REMEDY. FOR CLAIMS ARISING HEREUNDER SHALL BE FOR DAMAGES. SELLER'S LIABILITY FOR ANY AND ALL LOSSES AND DAMAGES TO. BUYER RESULTING FROM ANY CAUSE WHATSOEVER INCLUDING. SELLER'S NEGLIGENCE, ALLEGED DAMAGES OR DEFECTIVE. Equipment IRRESPECTIVE OF WHETHER SUCH DEFECTS ARE. DISCOVERABLE OR LATENT, SHALL IN NO EVENT EXCEED THE. PURCHASE PRICE OF THE PARTICULAR Equipment WITH.


Related search queries