QUALIFIED PRODUCTS LIST - Oregon

1 Oregon DEPARTMENT OF TRANSPORTATION CONSTRUCTION SECTION QUALIFIED PRODUCTS LIST PUBLISHING DATE: JANUARY 2018 This list is updated every six months and is available only from the Internet. Please notify the Product Evaluation Coordinator, in the Construction Section at the ODOT Materials Laboratory, of any changes in Standard Drawings, Special Provisions, or Specifications, etc., which would require additions to, deletions from, or changes to this listing. QUALIFIED PRODUCTS LIST Oregon DEPARTMENT OF TRANSPORTATION The " QUALIFIED PRODUCTS LIST" (QPL) is a comprehensive list of all finished PRODUCTS which have been evaluated and/or used by the Oregon DOT. The " QUALIFIED PRODUCTS LIST" is made up of two types of lists: 1. The QUALIFIED LIST - Q is for PRODUCTS that have been reviewed and found to be suitable for use in a specific category.

2 Job control testing may still be necessary. Consult the ODOT Nonfield-Tested Materials Acceptance Guide", the "ODOT Field-Tested Materials Acceptance Guide", and the Project Specifications. 2. The APPROVED LIST - A is for commercially available PRODUCTS having a low consequence of failure. These PRODUCTS are only usable for appropriate applications. May Require a Field Inspection Report. State existence on the Approved List and recognition of the product. No additional sampling or testing is needed. Specific questions regarding PRODUCTS on the un-published CONDITIONAL LIST can be answered by calling 503/986-3059. Conditionally Approved PRODUCTS need specific, prior approval for each project. Approval is given for one project at a time. The use of all PRODUCTS is restricted to the category in which they are listed.

3 PRODUCTS should be used and installed as the manufacturer recommends. The QPL does not distinguish between domestic and foreign steel. Use of this list by ODOT Maintenance Personnel as an information resource is encouraged not required. Note: Any change to a product on the QPL, without prior approval, will be cause for rejection of the product. Description Page # Index by Category, for Spec #.. I-II Traffic Control III Erosion Control Devices .. IV - V Pavement Markings .. VI - VII QUALIFIED & Approved 214 by Spec Number Reinforcing Steel .. A1-A11 The QPL and submittal forms are accessible from the Internet: QUALIFIED PRODUCTS Web Page Although the PRODUCTS listed may be approved for use, they are not exempt from State Purchasing Rules, practices and guidelines, or manufacturer s warrantees or guarantees.

4 If you have questions, contact: Oregon Department of Transportation 800 Airport Rd SE, Salem, OR 97301-4798 Dean Chess, Phone: 503/986-3059 E-Mail: FAX: 503/986-3096 PAGE I CATEGORYSPEC # CATEGORYSPEC # CATEGORYSPEC #ANTI-GRAFFITI COATING - BARRIER STOP/SLOW COLD PATCH - HI MODIFIER - TIE, RELEASE SCM - REPAIR OF FLAGGER ASSIST. SCM - FLY - SUBGRADE SCM - GGBF - TYPE I , SCM - PANELS, SCM - SILICA , SEALER - water , , SURFACE , INJECTION, , NON-EPOXY (NON SHRINK) AGENT, BLANKET, , AGENT, COMPOUND, , , PROOFING, BLOCKS, , - (TYPES 1 to 6) STRENGTHENING WET LAY WARNING ATTENUATOR, , TRENCH (PREFORMED) ATTENUATOR, ATTENUATOR, TRUCK FOR REBAR CUTTABLE FILLER, & CRACK SEALER HIGH MOD. EMULSION & CRACK SEALER LOW MOD. JOINTS, SEALANTS, ANCHOR, , WORKZONE FOR ANCHOR, STATION FOR GALV Oregon DEPARTMENT OF TRANSPORTATION "QPL" INDEX BY CATEGORY TO GET SPECIFICATION NUMBERSPAGE II CATEGORYSPEC# CATEGORYSPEC# CATEGORYSPEC#LUBE FOR STAINLESS / PVMS - CHNGABLE MESSAGE ARROW CHANNELIZING COVERS, RISER STEEL SQ TUBE - SHEETING TYPE O4, WORKZONE STEEL SQ TUBE - SLIP SHEETING, TYPES I - , TUBULAR AND STEEL SQ TUBE - SHEETING, WORKZONE , TUBULAR, SURF.

5 MTD, SUPPORTS, , TUBULAR, SURF. MTD, - WORK ZONE SYSTEM , LONGITUDINAL - - BIO , LONGITUDINAL - HIGH - , LONGITUDINAL - , CONTROL , , POLYMER COATINGS FOR METAL STEEL , SPRAY DRUMS, STEEL RETENTION CHEM FOR FIBER, MACRO, MICRO, JOINT FILLER, - LAYER POLY. CON. SEALANT, SILICONE (2 PART) , VEHICLE SPEED , MARKER , TEMPORARY MARKER, SIGNAL, MARKER, SPLICE, RUMBLE STRIPS, ELEMENTS FOR REPAIR POLYMER , HEADED - REPAIR, PRESERVATIVE, Oregon DEPARTMENT OF TRANSPORTATION "QPL" INDEX BY CATEGORY TO GET SPECIFICATION NUMBERS PAGE III Traffic Control Devices Notice (1-2018) The American Association of Stale Highway and Transportation Officials (AASHTO) recently published the Manual for Assessing Safety Hardware (MASH). MASH is an update to and supersedes NCHRP Report 350.

6 Requirements in Section 1408 of SAFETEA-LU stated that "The Secretary, in cooperation with the Association [ , AASHTO], shall publish updated guidance regarding the conditions under which States, when choosing to improve or replace highway features on the NHS, should improve or replace such features .. ". The AASHTO/FHWA Implementation Plan was developed to satisfy that requirement. Category 1: Plastic Tubular Markers, Plastic Barrels. ODOT Link for Self-Certification form: Click Here Category 2: Portable Sign Supports, Tripod Mounted AFAD s, Type 3 Barricades, etc. Category 3: Impact Attenuators, Guardrail, etc. Category 4: Trailer Mounted: Sequential Arrows, Message Boards, AFAD s, Flagger Station Lighting, Radar Speed (Trailers). etc. It is the responsibility of the Contractor to ensure they use a product that complies with the appropriate requirements.

7 FHWA Office of Safety: Countermeasures that Reduce Crash Severity: NCHRP Report 350: MASH: FHWA Work zone Letter WZ-161: Rev 1-2016 Erosion Control Page IV Category Remarks Section Check Dam Type 1 Aggregate .. Type 2 Straw Bale Type 3 Bio filter Bag Type 4 Sand Bag Type 5 Prefabricated Check Dam System Type 6 Compost Filter Sock Chemical Dust Control Type 1 Liquid .. Type 2 Dry Drainage Flow Spreader .. Inlet Protection Type 1 Sediment Fence .. Type 2 Geotextile w/Aggregate Filter Type 3 Prefabricated Filter Insert (Standard and Oil/Gas Versions) Type 4 Bio filter Bag Type 5 Masonry and Aggregate Type 6 Sod Type 7 Compost Filter Sock Type 8 - Other Matting** Slope Type A - Slopes 1:3 or flatter - Clay Soil .. Type B - Slopes 1:3 or flatter - Sandy Soil Type C - Slopes steeper than 1:3 - Clay Soil Type D - Slopes steeper than 1:3 - Sandy Soil Matting** Flexible Channel Liner Type E - Shear Stress Range 0 96 Pascals (0 2 lbs/sq ft).

8 Type F - Shear Stress Range 0 192 Pascals (0 4 lbs/sq ft) Type G - Shear Stress Range 0 287 Pascals (0 6 lbs/sq ft) Type H - Shear Stress Range 0 383 Pascals (0 8 lbs/sq ft) **Texas DOT Website for use with Mattings: Rev 1-2016 Page V Erosion Control Category Remarks Section Mulches, Temporary .. Outlet Protection Type 1 In Channel .. Type 2 End of Pipe Type 3 Flocculent Plastic Sheeting .. Sediment Barrier, Temporary Type 1 Straw Bale .. Type 2 Bio Filter Bag Type 3 Fiber Rolls (Wattles) Type 4 Sand Bags Type 5 Brush Barriers Type 6 Filter Berm Type 7 Pre-Fabricated Sediment Barrier Type 8 Compost Filter Sock Type 9 Compost Filter Berm Sediment Fence .. Sediment Mat .. Slope Drain, Temporary .. Slope Protection Type 1 Soft Armoring .. Type 2 Cellular Confinement Type 3 Other Page VI Pavement Markings (1 of 2) (1-18) Longitudinal Durable Pavement Markings Section Category Applications Material Method (A) (S) Surface (P) Profile, 120 Mils w/ bumps (1) Methyl Methacrylate (MMA) Extruded (G) Grooved (NP) Non-Profile (2) Thermoplastic Category Applications Material Method (B) (S) Surface (P) Profile, 120 Mils w/ bumps (1) Methyl Methacrylate (MMA) Sprayed (G) Grooved (NP) Non-Profile (2) Thermoplastic Category Applications Method (C)

9 Pavement Marking Tape Rolled-In Non-Patterned Tape Pavement Marking Tape Rolled-In Patterned Pavement Marking Tape Grooved Non-Patterned Pavement Marking Tape Grooved Patterned Pavement Marking Tape Rolled-In Patterned Wet Weather Pavement Marking Tape Grooved Patterned Wet Weather Category Applications Material Method (D) (S) Surface (P) Profile, 120 Mils w/ bumps (1) Methyl Methacrylate (MMA) Wet Weather (G) Grooved (NP) Non-Profile (2) Thermoplastic Page VII Pavement Markings (2 of 2) Longitudinal High Performance Pavement Markings Category Applications Material Method 1 - Extruded (S) Surface (G) Grooved Method 2 Spray Applications Material (S) Surface Plural Component (G) Grooved Hi-Build Paint Plural Component Wet Weather Hi-Build Paint Wet Weather Transverse Durable Pavement Markings Category Applications & Material Type A Liquid Hot Poured Thermoplastic with intermixed and top-dressed beads, 120 Mils Type B Preformed Fused Thermoplastic with intermixed beads, 125 Mils Type B-HS Preformed Fused Thermoplastic with intermixed beads, 125 Mils (HS= Hi Skid Resistance)

10 ODOT CONSTRUCTION / MATERIALS SECTION QUALIFIED PRODUCTS LIST APPROVED LIST - NO SAMPLES OR TESTS REQUIRED* QUALIFIED LIST - ADDITIONAL REQUIREMENTS**JANUARY 2018 STANDARD SPEC #CATEGORYPRODUCT NAMELOCAL REPRESENTATIVEAND/OR MANUFACTUREREFFECTIVE DATEPRODUCTNUMBERLISTREMARKSPage STOP/SLOW PADDLEFLASHINGBLINKER PADDLETAPCO 800/236-011208/14/05 3008 APERIMETER ON BOTH LIGHTS AROUND THETRAFFIC SAFETY 800 STOP/SLOW PADDLELIGHTED - HAND HELDTRAFF-ALERT 18 (TA18 AXTP)SAFECO 480/290-522004/08/10 4097 AHAND HELD STOP/SLOW PADDLELIGHTED - POLE MOUNTEDTRAFF-ALERT 18 (TA18AX6SP)SAFECO 480/290-522004/08/10 4099 APOLE STOP/SLOW PADDLEROLL-UP, NON-FLASHINGEMERGENCY USE ONLYFAN-A-SIGN MODEL MR18 SPORTNIKS, 2471 ASNAP ON HANDLE TO BE SEMI-RIGID. FOR EMERGENCY USE SHEETING. MUST HAVE505 STOP/SLOW PADDLEROLL-UP, NON-FLASHINGEMERGENCY USE ONLYSTOP SLOW PADDLE DG, ROLL-UPPACIFIC SAFETY SUPPLY04/13/00 1922 ASHEETING.