Qualitech Testing & Consultancy Limited 匯駿檢測 …

1 Contact Details Registration No. HOKLAS 179 Page 1 of 1 179 TEST CAL Qualitech Testing & Consultancy Limited ADDRESS : Flat E & F, 9/F, Block B, Universal Industrial Centre, 19-25 Shan Mei Street, Fo Tan, New Territories, Hong Kong 19-25 B 9 E F ENQUIRY : Mr Stanley TSE Wai-lai, General Manager TELEPHONE : 2185 0900 FAX : 2687 6752 E-MAIL : WEBSITE ADDRESS : CLIENTELE : Public Contact details last updated on: 18 July 2016 Scope of Accreditation Registration No. HOKLAS 179 Page 1 of 45 Issue Date: 8 June 2020 Ref: HOKLAS179-96 Qualitech Testing & Consultancy Limited 179 TEST CAL ADDRESS Main Laboratory : Flat E & F, 9/F, Block B, Universal Industrial Centre, 19-25 Shan Mei Street, Fo Tan, New Territories, Hong Kong 19-25 B 9 E F Test Locations.

2 Flat G, 9/F, Block B, Universal Industrial Centre, 19-25 Shan Mei Street, Fo Tan, New Territories, Hong Kong 19-25 B 9 G 1B, G/F, Yale Industrial Centre, 61-63 Au Pui Wan Street, Fo Tan, New Territories, Hong Kong 61-63 1B Unit 11, G/F, Veristrong Industrial Centre, 34-36 Au Pui Wan Street, Fo Tan, New Territories, Hong Kong 34-36 11 Workshop E2 & E52, 9/F, Wah Lok Industrial Centre (Phase II), 31-35 Shan Mei Street, Fo Tan, New Territories, Hong Kong 31-35 ( ) 9 E2 E52 Workshop E6, 21/F, Wah Lok Industrial Centre (Phase II), 31-35 Shan Mei Street, Fo Tan, New Territories, Hong Kong 31-35 ( ) 21 E6 ACCREDITED TEST CATEGORY : Calibration Services Construction Materials Environmental Testing Miscellaneous Scope of Accreditation Registration No.

3 HOKLAS 179 Page 2 of 45 Issue Date: 8 June 2020 Ref: HOKLAS179-96 Qualitech Testing & Consultancy Limited 179 TEST CAL Flat G, 9/F, Block B, Universal Industrial Centre, 19-25 Shan Mei Street, Fo Tan, New Territories, Hong Kong 19-25 B 9 G Calibration Services ITEM TESTED OR MEASURED SPECIFIC TEST OR PROPERTY MEASURED@ @ CALIBRATION AND MEASUREMENT CAPABILITY (CMC)* * Construction materials Testing equipment - Cement grout flow cone Determination of the time of efflux of water s in accordance with ASTM C939-02 Cl. 8 or ASTM C939-10 Cl. 9 - Compacting bar Verification in accordance with in-house method CAL-COMPBAR for the dimensional and mass requirements as specified in CS1: 2010 Vol.

4 1 App. A10 or CS1: 1990 Vol. 1 (Amd. 1102) App. A9 - dimension of ramming face mm - length mm - mass 4 g - Covermeter Calibration in accordance with mm BS 1881: Part 204: 1988 Cl. (Method C) 20 mm to 120 mm - Cube mould Verification in accordance with in-house method CAL-CUBEMOULD for the dimensional requirements as specified in CS1: 2010 Vol. 1 App. A25 or CS1: 1990 Vol. 1 App. A21 excluding App. (e) - dimension mm - flatness mm - perpendicularity mm - parallelism mm @ UNLESS OTHERWISE SPECIFIED, ACCREDITED ACTIVITIES ARE CONDUCTED AT THE LABORATORY.

5 * THE CALIBRATION UNCERTAINTY OF A DEVICE UNDER TEST IS USUALLY REPORTED AT 95% CONFIDENCE LEVEL AND DEPENDS ON BOTH THE CMC OF THE LABORATORY AND THE PERFORMANCE OF THE DEVICE DURING CALIBRATION. Scope of Accreditation Registration No. HOKLAS 179 Page 3 of 45 Issue Date: 8 June 2020 Ref: HOKLAS179-96 Qualitech Testing & Consultancy Limited 179 TEST CAL Flat G, 9/F, Block B, Universal Industrial Centre, 19-25 Shan Mei Street, Fo Tan, New Territories, Hong Kong 19-25 B 9 G Calibration Services ITEM TESTED OR MEASURED SPECIFIC TEST OR PROPERTY MEASURED@ @ CALIBRATION AND MEASUREMENT CAPABILITY (CMC)* * Construction materials Testing equipment (cont d) - Cube mould On-site verification in accordance with in-house method CAL-CUBEMOULD for the dimensional requirements as specified in CS1: 2010 Vol.

6 1 App. A25 or CS1: 1990 Vol. 1 App. A21 excluding App. (e) - dimension mm - flatness mm - perpendicularity mm - parallelism mm - Curing tank On-site verification in accordance with in-house method CAL-CURTANK for the requirements as specified in CS1: 1990: Vol. 1 App. A24 or CS1: 2010: Vol. 1 App. A28 - temperature distribution K - efficiency of circulation min - Flow mould for determination of flow of Verification in accordance with fresh concrete in-house method CAL-FLOWMOULD for the dimensional requirements as specified in CS1: 1990 Vol.

7 2 (Amd. 1206) App. E2, CS1: 2010 Vol. 1 App. , or BS EN 12350-5: 2009 Cl. - diameter mm - wall thickness mm - height mm @ UNLESS OTHERWISE SPECIFIED, ACCREDITED ACTIVITIES ARE CONDUCTED AT THE LABORATORY. * THE CALIBRATION UNCERTAINTY OF A DEVICE UNDER TEST IS USUALLY REPORTED AT 95% CONFIDENCE LEVEL AND DEPENDS ON BOTH THE CMC OF THE LABORATORY AND THE PERFORMANCE OF THE DEVICE DURING CALIBRATION. Scope of Accreditation Registration No. HOKLAS 179 Page 4 of 45 Issue Date: 8 June 2020 Ref: HOKLAS179-96 Qualitech Testing & Consultancy Limited 179 TEST CAL Flat G, 9/F, Block B, Universal Industrial Centre, 19-25 Shan Mei Street, Fo Tan, New Territories, Hong Kong 19-25 B 9 G Calibration Services ITEM TESTED OR MEASURED SPECIFIC TEST OR PROPERTY MEASURED@ @ CALIBRATION AND MEASUREMENT CAPABILITY (CMC)* * Construction materials Testing equipment (cont d) - Flow table for determination of flow of Verification in accordance with fresh concrete in-house method CAL-FLOWTABLE for the dimensional and mass requirements as specified in CS1: 1990 Vol.

8 2 (Amd. 1206) App. E1, CS1: 2010 Vol. 1 App. , or BS EN 12350-5: 2009 Cl. - plane area mm - other essential dimensions mm - mass kg - Flow tamping bar for determination of flow of Verification in accordance with fresh concrete in-house method CAL-FLOWTAMPBAR for the dimensional requirements as specified in CS1: 1990 Vol. 2 (Amd. 1206) App. E3, CS1: 2010 Vol. 1 App. , or BS EN 12350-5: 2009 Cl. - tamping face mm - length of bar mm - Mixer On-site calibration in accordance with in-house method CAL-MIX-SP for the speed of rotation over the following ranges : 20 rpm to 1000 rpm 1 rpm above 1000 rpm to 2000 rpm 2 rpm @ UNLESS OTHERWISE SPECIFIED, ACCREDITED ACTIVITIES ARE CONDUCTED AT THE LABORATORY.

9 * THE CALIBRATION UNCERTAINTY OF A DEVICE UNDER TEST IS USUALLY REPORTED AT 95% CONFIDENCE LEVEL AND DEPENDS ON BOTH THE CMC OF THE LABORATORY AND THE PERFORMANCE OF THE DEVICE DURING CALIBRATION. Scope of Accreditation Registration No. HOKLAS 179 Page 5 of 45 Issue Date: 8 June 2020 Ref: HOKLAS179-96 Qualitech Testing & Consultancy Limited 179 TEST CAL Flat G, 9/F, Block B, Universal Industrial Centre, 19-25 Shan Mei Street, Fo Tan, New Territories, Hong Kong 19-25 B 9 G Calibration Services ITEM TESTED OR MEASURED SPECIFIC TEST OR PROPERTY MEASURED@ @ CALIBRATION AND MEASUREMENT CAPABILITY (CMC)* * Construction materials Testing equipment (cont d) - Rebound hammer Determination of rebound value 1 rebound count in accordance with in-house method CAL-REBHAM using anvil complying with BS EN 12504-2.

10 2001 Cl. - Slump cone Verification in accordance with in-house method CAL-SLUMPCONE for the dimensional requirements as specified in CS1: 1990 Vol. 1 App. A4, CS1: 2010 Vol. 1 App. A5, or BS EN 12350-2: 2009 Cl. - diameter mm - wall thickness mm - height mm - Slump flow base plate Verification in accordance with in-house method CAL-SFBASEPL for the dimensional requirements as specified in CS1: 2010 Vol. 1 App. A16 or BS EN 12350-8: 2010 Cl. - thickness mm - flatness mm - other essential dimensions mm @ UNLESS OTHERWISE SPECIFIED, ACCREDITED ACTIVITIES ARE CONDUCTED AT THE LABORATORY.