Recoatable High Gloss Clear Polyurethane Finish …

1 QUANTUM CLEARCOAT. Recoatable high Gloss Clear Polyurethane Finish PC 435. FEATURES OUTSTANDING WEATHERING AND CHEMICAL RESISTANCE. HEADING 3 EXCELLENT APPLICATION PROPERTIES. ARIAL 9 BOLD EXCELLENT GRAFFITI RESISTANCE. high Gloss CLEARCOAT AVAILABLE.. USES QUANTUM CLEARCOAT Gloss is a premium quality, high Gloss crystal Clear two-pack acrylic Polyurethane . QUANTUM has been designed for superior weathering and Gloss retention even in areas of extreme UV. radiation. QUANTUM is readily Recoatable with minimal surface preparation. Ideal for almost any substrate and situation. QUANTUM CLEARCOAT Gloss , when used over QUANTUM FX imparts exceptional Gloss , depth of colour and sparkle and offers very high visual impact to areas of high public scrutiny such as hotel lobbies, commercial facades, restaurant and cafe interiors, showrooms, awnings, lifts, furniture, and many areas in sporting facilities and retail complexes.

2 QUANTUM , when fully cured, exhibits excellent graffiti resistance. SPECIFICATIONS AS/NZS RESISTANCE GUIDE. WEATHERABILITY Excellent Gloss retention on exterior SOLVENTS Excellent resistance to splash and exposure spillage of common alcohols, aliphatic and aromatic hydrocarbons, esters and ketones HEAT RESISTANCE Up to 120 C dry heat WATER Excellent resistance to fresh and salt water but not suitable for immersion SALTS Unaffected by splash and spillage of most ALKALIS Good resistance to splash and salt solutions spillage of most common alkalis ACIDS Suitable for splash and spillage exposure to ABRASION Excellent when fully cured most acids TYPICAL PROPERTIES AND APPLICATION DATA.

3 CLASSIFICATION Acrylic Polyurethane coating APPLICATION CONDITIONS. Finish high Gloss Min Max COLOUR Clearcoat Gloss Air Temp. 10 C 45 C. Substrate Temp. 10 C 45 C. Relative Humidity 85%. Concrete Moisture <10%. COMPONENTS Two VOLUME SOLIDS 43% (Clearcoat) COATING THICKNESS (MICRONS). VOC LEVEL <510 g/L (Clearcoat) Min Max Recommended FLASH POINT -7 C (Clearcoat) Wet film per coat ( m) 80 130 100. POT LIFE2 hours (4L, 25 C) Dry film per coat ( m) 35 55 45. MIXING RATIO V/VPart A : 3 Part B : 1. THINNER BRUSH 965-42166 Duthin 040 SUITABLE Suitably primed steel, aluminium, THINNER SPRAY 965-42166 Duthin 040 SUBSTRATES MDF, galvanised steel, concrete or 965-63023 Dulux Urethane Thinner fibreglass PRODUCT CODE 722-30900 Clearcoat Gloss PRIMERS Most Dulux two pack epoxy primers 976-87350 Standard Hardener and single pack oil based primers TOPCOATS Most Dulux single pack and two pack topcoats APPLICATION Brush, roller, conventional, airless METHODS spray or air assisted spray DRYING CHARACTERISTICS AT 45 m DRY FILM THICKNESS.

4 OVERCOAT. Temperature Humidity Touch Handle Full Cure Min Max 25 C 50% 1 Hour 5 Hours 7 Days 5 Hours Indefinite These figures are a guide only, as ventilation, film thickness, humidity, thinning and other factors will influence the rate of drying. SPREADING RATE square metres per litre equals 45 m dry film thickness ASSUMING NO LOSSES NOTE: Practical spreading rates will vary depending on such factors as application method, ambient conditions, surface porosity and roughness. PC 435 September 2015 Page 1 of 3. QUANTUM CLEARCOAT. TYPICAL SYSTEMS. This is a guide only and not to be used as a specification. Your specific project needs must be discussed with a Dulux Protective Coatings Consultant.

5 SURFACE ENVIRONMENT PREPARATION GUIDE SYSTEM DFT ( m). st . 1 Coat Zincanode 402 75 m Coastal Duremax GPE MIO. Abrasive blast clean 2nd Coat 200 m STEEL NEW ( Cat C5). Class 3rd Coat Quantum FX 55 m Exceeds System PUR5. 4th Coat Quantum Clearcoat 45 m . Low Interior 1st Coat Durepon P14 75 m Abrasive blast clean STEEL NEW ( Cat C2) 2nd Coat Quantum FX 55 m Class Exceeds System PUR2 3rd Coat Quantum Clearcoat 45 m . 1st Coat Durebild STE 125 m Remove release agents and other nd CONCRETE Exterior/Interior 2 Coat Quantum FX 55 m surface contaminants 3rd Coat Quantum Clearcoat 45 m . 1st Coat Luxepoxy 4 White Primer 50 m HARDWOOD & Sand and dust down before and nd Interior 2 Coat Quantum FX 55 m MDF after first coat 3rd Coat Quantum Clearcoat 45 m.

6 1st Coat Luxepoxy 4 White Primer 50 m ALUMINIUM & Clean, degrease and abrade Exterior/Interior 2nd Coat Quantum FX 55 m FIBREGLASS surface 3rd Coat Quantum Clearcoat 45 m . 1st Coat Luxepoxy 4 White Primer 50 m FIBRE CEMENT Clean, degrease and lightly sand nd Exterior/Interior 2 Coat Quantum FX 55 m SHEET surface. Dust down. 3rd Coat Quantum Clearcoat 45 m NOTE: If application is by brush or roller, additional coats will be necessary to achieve the minimum DFT and full opacity. Appearance may greatly differ depending on application method (brush, roller and spray).. Plasterboard surfaces may move and crack, particularly at the joints. Quantum FX is not sufficiently flexible to be suitable over surfaces prone to movement, therefore, ensure that any movement is borne by expansion joints and that these joins are masked off when applying Quantum FX.

7 SURFACE Specifiers should follow the surface preparation guidelines from the data sheet . for the primer selected. The PREPARATION surface must be free from grease, oil, dirt, rust and other contaminants. Dulux recommends that surfaces be degreased with Gamlen CA No. 1 (a free-rinsing, alkaline detergent) according to the manufacturer's written instructions and all safety warnings. Steel: Round off all rough welds, sharp edges and remove weld spatter. Remove grease, oil and other contaminants in accordance with Abrasive blast clean to a minimum of Class Concrete: Concrete must be at least 28 days old before all laitance, form release, curing compounds, oil, grease and other surface contaminants.

8 Diamond grind, track or light shot-blast concrete floors to remove laitance and provide suitable profile. Remove all dust by vacuum cleaning. Fill any large cracks or voids using Luxepoxy Filler. MDF and hardwood: Sand thoroughly and remove all dust. Resand lightly after application of primer to remove raised fibres Non ferrous metals: Round off all sharp edges. Remove grease, oil and other contaminants in accordance with Whip blast with fine non-metallic media such as plastic, glass or garnet. Remove all dust with compressed air. Alternatively, degrease and abrade the surface with a non-metallic abrasive pad, such as Scotch-Brite scourer wetted with Gamlen CA No.

9 1 (a free-rinsing, alkaline detergent) and water. Rinse thoroughly with fresh water. For best appearance of the Finish the primer surface must be smooth and free of any defects. When sanding work from coarse to fine grades of paper to avoid sanding marks in the Finish . PC 435 September 2015 Page 2 of 3. QUANTUM CLEARCOAT. APPLICATION Mix each can thoroughly using a power mixer . until the contents are uniform. Ensure bases have been tinted to the correct colour before use. DULUX ASSUMES NO RESPONSIBILITY FOR THE APPLICATION OF. INCORRECT COLOUR. Mix the contents of both packs together thoroughly with a power mixer and let stand for 10 minutes. Box all containers before use to ensure colour consistency.

10 Remix thoroughly before and during application to prevent settling. BRUSH/ROLLER Suitable for small areas only. Thin with up to 100 ml/litre with Duthin 040 (965-42166) to aid application. When brushing and rolling additional coats may be required to attain the specified thickness and full opacity. Colour and appearance are dependent on thinning levels and application technique. The effect achieved will differ from that obtained by spray application. CONVENTIONAL Up to 200ml/litre Dulux Urethane Thinner can be used to aid atomisation. Apply in multiple wet on wet coats SPRAY overlapping each pass 50%. Between two and four wet on wet coats are required to achieve opacity.