Redwood Lumber Patterns

1 Redwood Lumber Patterns No. 17. 3 Redwood GRADEMARKS. 3 Patterns PROFILED IN THIS BOOK. 3 SURFACE TEXTURE. 3 grain . 3 CONVERSION FACTORS. 3 FURTHER INFORMATION. 4 S4S DRY DIMENSIONS. 4 S4S GREEN DIMENSIONS. 4 DESCRIPTION OF ABBREVIATIONS. 5-9 TABLE OF CONTENTS. Redwood Patterns 10-12 TONGUE AND GROOVE. 13 NAILING TONGUE & GROOVE Patterns . 14-15 SHIPLAP. 16 NAILING SHIPLAP Patterns . 17-19 BEVEL. 20 NAILING BEVEL Patterns . California 21 DECKING. Redwood 22 PLOWED FASCIA. Association 405 Enfrente Drive, Suite 200. 23 FENCING. Novato, California 94949-7201 24 MOULDING. Telephone 415 382-0662. Toll Free 888 Cal- Redwood 25-26 INDEX. Fax 415 382-8531. Redwood our renewable resource 1/04 1. CRA Member Companies and General Redwood Sales Offices Redwood GRADEMARKS grain . Listed on this page are the member mills of the Redwood grades and Patterns are established by the Redwood sidings are sold as vertical grain (VG), flat California Redwood Association.

2 Individually, each Redwood Inspection Service which is the official Redwood grain (FG) or mixed grain (MG). The annual growth rings member has earned a distinguished reputation for Britt Lumber Company, Inc. excellence in the production of Redwood Lumber grading agency accredited by the American Lumber in vertical grain Lumber form an angle of 45 degrees Box 248 Standard Committee, Inc., Board of Review. Grade rules or more with the surface of the piece. All Lumber not products. Combined under the CRA hallmark, they Arcata, California 95518-0248 are published in the Standard Specifications for Grades meeting this requirement is known as flat grain . continuously seek improvements in the processing Phone 707 822-1779 of California Redwood Lumber . Vertical grain Lumber has superior performance and utilization of Redwood .

3 Thus, the CRA signature FAX 707 822-5645. on Redwood Lumber assures that it has been manu- Properly grademarked Lumber will bear the RIS mark qualities in the areas of dimensional stability and finish- factured to the highest quality standards. or that of another accredited inspection bureau. The holding characteristics. mLaUdM rB iEvRer CRA trademark is on products of the member mills of the California Redwood Association only and is an additional assurance of quality. Vertical grain Flat grain Redwood Fencing Experts Standard grademarks include the grade designation Box 1134 and the symbol of an authorized grading agency. They Arcata, CA 95518-1134 shall also identify the manufacturer and the moisture Annual rings Bark side Pith side Phone 707 822-4384 content at the time of manufacture. Grademarks may FAX 707 822-2195 appear on the face, edge or end of a piece.

4 CONVERSION FACTORS. Conversion factors for siding, paneling, decking and MILL 000 fencing Patterns are based on surface measure and must CERTIFIED be doubled to calculate board measure for 2-inch KILN DRIED Lumber Patterns . To estimate surface measure, multiply . CLR RWD the area to be covered (in square feet) by the con- version factor. This factor allows for width lost in dressing Mendocino Forest Products Company, LLC. or lapping. Add three to five percent for end cutting and 420 Aviation Blvd. #103 Lumber that has been kiln dried according to Santa Rosa, CA 95403 matching on the job. accepted standards includes the words Certified Kiln Phone 707 576-8240. Dried or the initials CKD in the grademark. FURTHER INFORMATION. Fax 707 576-8259. In some cases, an RIS Certificate of Inspection may be used to identify the Lumber grade.

5 The California Redwood Association publishes a wide Certificates of Inspection include all the pertinent variety of publications relating to Redwood products. information described above as well as the name of Contact the Association for product, technical and pro- the producer and the inspector. motional information or go to to view and download literature that is of interest to you. Box 565 Patterns PROFILED IN THIS BOOK. Grade rules for Redwood : Scotia, California 95565-0565 Illustrated on the following pages are the pattern Phone 707 764-8888 Standard Specifications for Grades of profiles of worked Redwood Lumber produced by the California Redwood Lumber FAX 707 764-4444. members of the California Redwood Association. These profiles and dimensions have been established Specifying Redwood : to simplify the specifying and ordering of pattern Lumber .

6 Redwood Grades & Uses All Patterns shown are pictured as they are usually Redwood Architectural Guide run through the matcher as viewed from the head of the Redwood Landscape Architecture machine looking toward the outfeed end. Schmidbauer Lumber Company Box 152 Applying Redwood : Eureka, California 95502-0152 SURFACE TEXTURE Redwood CKD Siding Patterns and Applications Phone 707 443-7024 Pattern Lumber Lumber shaped to a pattern or Redwood Deck Construction FAX 707 443-2356 moulded form is supplied surfaced (smooth planed) or saw-textured. Many products are produced surfaced Finishing Redwood : one side and saw-textured one side. This surface is Redwood Exterior Finishes derived from resawing at the planer mill and is not to be Redwood Interior Finishes Simpson Timber Company confused with the surface of rough Lumber (the initial Painting Redwood Siding: Guidelines to Extending Box 1089 product manufactured at the headrig in a sawmill).

7 Maintenance Cycles Arcata, California 95518-1089 Saw-textured surfaces are preferable for many Phone 800-637-7077. applications because they hold finishes better and FAX 707 268-3089. show blemishes less. 2 3. S4S DRY DIMENSIONS. (INCHES). Nominal Dressed1 Nominal Dressed Nominal Dressed 1x 2 11 16 x 11 2* 11 4 x 2 1x11 2* 2x2 11 2 x1 1 2* Redwood . 1x 3. 1x 4. 11 16 x 2 1 2**. 11 16 x 3 1 2. 11 4 x 3. 11 4 x 4. 1x 2 1 2**. 1x 3 1 2. 2x3. 2x4. 11 2 x 2 1 2**. 11 2 x 3 1 2 TONGUE AND GROOVE. 1x 6. 1x 8. 11 16 x 5 1 2. 11 16 x7 1 4. 11 4 x 6. 11 4 x 8. 1x 5 1 2. 1x7 1 4. 2x6. 2x8. 11 2 x 5 1 2. 11 2 x7 1 4 Patterns . 1x10 11 16 x9 1 4 11 4 x10 1x9 1 4 2 x10 11 2 x9 1 4. 1x12 11 16 x11 1 4 11 4 x12 1x111 4 2 x12 11 2 x11 1 4. *Also available surfaced at 15 8 inch net. **Also available surfaced at 25 8 inch net. MOST SIZES AVAILABLE S1S2E SAW-TEXTURED ONE SIDE2 PATTERN PATTERN.

8 NUMBER DESCRIPTION PAGE NUMBER DESCRIPTION PAGE. 16 1x 6 T&G Paneling (S2S-CM) 10 711 1x 6 T&G (V1S-S2S) 1 4"V 12. 17 1x 8 T&G Paneling (S2S-CM) 10 711R 1x 6 T&G (V2S-S1S-Saw-textured 1S). 1 4"V 12. S4S GREEN DIMENSIONS 18 1x10 T&G Paneling (S2S-CM) 10. 712 1x 8 T&G (V1S-S2S) 1 4"V 12. (INCHES) 204 5/8 x 4 T&G (V1S-S2S) 3/32"V 10. 205 5/8 x 6 T&G (V1S-S2S) 3/32"V 10 712R 1x 8 T&G (V2S-S1S-Saw-textured 1S). 1 4"V. Nominal Dressed1 Nominal Dressed Nominal Dressed 5/ 8 x 8 3/32"V. 12. 206 T&G (V1S-S2S) 10. 713 1x10 T&G (V1S-S2S) 1 4"V 12. 1x 2 25 32 x1 9 16 11 4 x 2 11 32 x1 9 16 2x2 19 16 x19 16 606 1x 6 T&G Drop Siding (S2S) 10 713R 1x10 T&G (V2S-S1S-Saw-textured 1S). 1x 3 25 32 x 2 9 16 11 4 x 3 11 32 x 2 9 16 2x3 19 16 x 2 9 16 1/4"V. 616 1x 6 T&G V&CV (S2S) 10 1 4"V 12. 1x 4 25 32 x 3 9 16 11 4 x 4 11 32 x 3 9 16 2x4 19 16 x 3 9 16 617 1x 8 T&G V&CV (S2S) 1/4"V 10 715 1x 8 T&G (V1S-S2S) 3 32"V 11.

9 1x 6 25 32 x 5 9 16 11 4 x 6 11 32 x 5 9 16 2x6 19 16 x 5 9 16. 25 32 x7 3 8. 632 1x 4 T&G (S2S-CM) 11 715R 1x 8 T&G (V2S-S1S-Saw-textured 1S). 1x 8 11 4 x 8 11 32 x7 3 8 2x8 19 16 x7 3 8 3 32"V. 25 32 x9 3 8 632EE 1x 4 T&G EE (S2S-CM) 11 11. 1x10 11 4 x10 11 32 x9 3 8 2 x10 19 16 x9 3 8. 1x12 25 32 x11 3 8 11 4 x12 11 32 x113 8 2 x12 19 16 x113 8 633 1x 6 T&G (S2S-CM) 11 716 1x10 T&G (V1S-S2S) 3 32"V 11. 633EE 1x 6 T&G EE (S2S-CM) 11 716R 1x10 T&G (V2S-S1S-Saw-textured 1S). 3 32"V 11. MOST SIZES AVAILABLE S1S2E SAW-TEXTURED ONE SIDE2 634 1x 8 T&G (S2S-CM) 11. 726R 1x 6 T&G (V2S-S1S-Saw-textured 1S). 634EE 1x 8 T&G EE (S2S-CM) 11 1 8"V 12. 1 Boards less than the minimum thickness for nominal 1 inch but 5/8 inch or greater thickness dry (11/16 inch green) shall be regarded as 707 1x 4 T&G (V1S-S2S) 3/32"V 11 727R 1x 8 T&G (V2S-S1S-Saw-textured 1S).

10 American Softwood Lumber Standard (ALS) Lumber , but such boards shall be marked to show the size and condition of seasoning at 1 8"V. 707R 1x 4 T&G (V2S-S1S-Saw-textured 1S) 12. the time of dressing. They shall also be distinguished from nominal 1-inch boards on invoices and certificates. 3/32"V. 2 Variation resulting from resawing surfaced Redwood Lumber may be plus or minus 1/32 inch. 11 728R 1x10 T&G (V2S-S1S-Saw-textured 1S). 708 1x 6 T&G (V1S-S2S) 3/32"V 11 1 8"V 12. DESCRIPTION OF ABBREVIATIONS NOTE: Lumber LESS THAN 2 INCHES THICK IS NORMALLY 708R 1x 6 T&G (V2S-S1S-Saw-textured 1S) 732R 1x 4 T&G (V2S-S1S-Saw-textured 1S). 3 32"V 11 1 4"V 12. ROUNDED AS NEAR AS POSSIBLE TO A 1 16-INCH RADIUS, T&G = TONGUE & GROOVE. 2-INCH Lumber TO A 1/8-INCH RADIUS. S4S Lumber MAY 709 1x 4 T&G (V1S-S2S) 1 4"V 12 733R 1x 6 T&G (V2S-S1S-Saw-textured 1S).