Example: barber
Reference Only Spec No. JENF243F-0031G-01 EMIFIL (Three ...
② Structure S : Built-in Ferrite Beads Type ③ Style ④ Features ⑤ Temperature Characteristics B3:±10%（-40～+85℃ at 20℃） ⑥ Rated Voltage 2A :2A→100VDC、1H→50VDC ⑦ Capacitance Marked three digits system.(Ex. 22pF→220、22000pF→223) ⑧ Lead Type Q55 : Bulk Lead Type :Straight Lead
Tags:
Information
Domain:
Source:
Link to this page:
Documents from same domain
Reference Only - Murata Manufacturing
www.murata.comChip Ferrite Bead BLM18 ... Current (mA) DC Resistance ( max.) Remark Initial Values Values After Testing ... high speed signal line BLM18BB050SN1B BLM18BA050SN1D 5±25% 5 500 0.2 0.3 BLM18BA050SN1B BLM18BB100SN1D 10±25% 10 700 0.10 0.20 BLM18BB100SN1B BLM18BA100SN1D
Chip Ferrite Bead BLM31 Murata Standard Reference ...
www.murata.comPer AEC-Q200-002 Meet Table A after testing. ESD Rank: Refer to Item 3. Rating 18 Solderability Per J-STD-002 Method b : Not Applicable 95% of the terminations is to be soldered. 19 Electrical Characterization Measured : Impedance No defects 20 Flammability Per UL-94 Not Applicable 21 Board Flex Epoxy-PCB(1.6mm) ...
Reference Only - Murata Manufacturing
www.murata.comPer AEC-Q200-002 Meet Table C after testing. ESD Rank: Refer to Item 3. Rating. 18 Solderbility Per J-STD-002 Method b : Not Applicable 75% of the terminations is to be soldered. 19 Electrical Characterization Measured :Capacitance No defects 20 Flammability Per UL-94 Not Applicable 21 Board Flex Epoxy-PCB(1.6mm) ...
Reference Only - Murata Manufacturing
www.murata.comIt shall be soldered on the Glass-epoxy substrate. Substrate : 100mm×40mm×0.8mm Deflection : 1.0mm Speed of Applying Force : 0.5mm/s Keeping Time : 30s 7-2-3 Vibration It shall be soldered on the substrate. Oscillation Frequency : 10Hz to 55Hz to 10Hz for 1 min Total Amplitude : 1.5mm Testing Time : A period of 2 hours in each of 3 mutually
Related documents
Reducing noise on the output of a switching regulator
www.ti.comFerrite beads Ferrite beads are common in noise-sensitive systems. They are popular for “soaking” up conducted EMI due to their AC resistance at high frequencies, which dissipates the noise as heat. The problem is that it may be difficult to select the proper ferrite bead for some applications because several parameters can
MT-101: Decoupling Techniques - Analog Devices
www.analog.comFerrite beads (nonconductive ceramics manufactured from the oxides of nickel, zinc, manganese, or other compounds) are also useful for decoupling in power supply filters. At low frequencies (<100 kHz), ferrites are inductive; thus they are useful in low-pass LC filters. Above 100 kHz, ferrites becomes resistive (high Q).
TOOLS - Anchor Electronics
anchor-electronics.comferrite beads 3 fuses 2 IC’s 6 inductors 4, 5 LEDs 3 opto isolators 6 resistors 2 switches 5 test clips 6 transistors 5 trimpots 2 voltage reg. 6 Surface Mount INDEX Arduino-related 24 bargain board 17 batteries 7 BNC 18 breadboards 7 bridge rectifiers 15 bumpers 7 cable ties 20 calipers 22 capacitors 12, 13 chemicals 23 & online
OneTechnologyWay P.O.Box9106 Norwood,MA 02062 …
www.analog.comFerrite beads are categorized by three response regions: inductive, resistive, and capacitive. These regions can be determined by looking at a ZRX plot, where Z is the impedance, R is the resistance, and X is the reactance of the bead. To reduce high
Understanding How Ferrites Can Prevent and Eliminate RF ...
audiosystemsgroup.comBelow resonance, the impedance of a ferrite choke is proportional to the length of the wire that is enclosed by the ferrite material. Fig 6 shows the impedance of a family of beads that differ primarily in their length. There are also small differences in their cross section, which is why the resonant frequency shifts slightly.
PCB Design and Layout Guide - ww1.microchip.com
ww1.microchip.comIn addition, a ferrite bead should be used to isolate each analog supply from the rest of the board. The bead should be placed in series between the bulk decoupling capacitors and local decoupling capacitors. Figure 2 • Decoupling Schematic The beads should be chosen to …
Ferrite and Common Mode Chokes - W4CAE
w4cae.comFerrite Mixes Ref 3 There are two basic ferrite material groups: … The NiZn ferrite cores (mix 43, 52, 61) have low permeability, exhibit high volume resistivity, moderate temperature stability and high ‘Q’ factors for the 500 KHz to 100 MHz frequency range. They are well suited for low power, high inductance resonant circuits.