RIXSON Heavy Duty Floor Closers - mfsales.com

1 160 AbsoluteControl: Heavy DutyFloor ClosersFloor Closers providethe best mechanicalmeans of controlling are designedto work with the lawsof physics to providelong lasting perfor-mance and on standard hinges are attached sideways into the doorand frame. As the door starts moving away from the opening, ten-sion is placed on the hinge screws and may ultimately pull themout of the frame and door. A door installed with a Floor closer andpivots sits directly on the top pivots are attachedwith screws up into the frame and down into the top of the order for the door to fall out of the frame opening, the screwswould have to shear off, which is highly forces and closing forces of Floor Closers are muchmore closely correlated than other door control devices. A floorcloser opening to 90 degrees with 11 pounds of opening forcewill have 4 pounds of closing force.

2 A standard surface closerprovides an 11 to 6 ratio between opening and closing , a Floor closer is far superior in closing a door, espe-cially when stack pressure or weather conditions are TypesnNon Hold-Open (NHO or N) closer not equipped with anyhold open Hold-Open (SHO or S) Factory-installed on certain series Closers . Hold-open may be turned Action (DA) Provided on barrier-free door to remain ajar (at 70 ) for up to 30 by separate valve and can be shut off if not available on Closers furnished with cold weather fluid,and not recommended for exterior applications because ofweather Handicapped (PH) Closers which have this feature are preset with 5 pounds of opening force at the factory. RIXSON s unique verticular spring allows completeadjustment of spring tension on Heavy duty Floor installations can be modified to meet new buildingcodes, without replacing the should be orderedfor interior doors Weather Fluid (CWF) Should be considered in installa-tions where ground temperature is constantly below +15 be used in temperatures as low as -35 closer (SC) Used where water contact may gasketing and a cover plate that are epoxied aroundthe case with the closer inside.

3 Not available for replacementclosers unless cement case is also Hold-Open (AHO or A) Available on certainseries Closers without deadstop. Preset at factory for specificdegree of hold open. Degree of hold-open cannot bechanged, nor can closer be made into nFloor Closers are fully concealed to maintain aesthetic designof the weight of door is borne by Floor closer providing trouble-free operation and long up to 1,500 pounds are accommodated, allowing standard and Heavy doors in a building to be hung by thesame offset or center hung to accommodate any adjustment provides for field adjustment of the doorif of Heavy panels on the door face with standardoffset Floor closer preparation Floor -to-ceiling concealment is offered for center hungdoors providing almost unlimited design spindles available to accommodate any Floor models available 3/4 or 1-1/2 models available for lead lined models available for fire door assemblies up to 3 tension and closing speed are field fully adjustable hydraulic backcheck standard on 27 and 28 in all standard architectural finishes 605, 612, 613.

4 625 and Floor Closers are available with electrical passthrough via the determine the hand of a door for ordering pivots or concealed Closers , face the door from the side which swingsaway from it opens to the left, it s it opens to the right, it s duty Floor ClosersToll Free: (800) 221-2052 nPhone: (718) 622-8785 or (516) 352-6262 nFax: (718) 789-8346 ne-mail: 25 PUSH SIDERIGHT HANDLEFT HAND 161 RIXSONH eavy duty Floor Closers20 SeriesOffset Hung Floor Closers nAll offset hung Floor Closers are single acting and offset Floor Closers locate the pivot point 3/4 from theheel edge of the door and 3/4 from the face of the offset Floor Closers locate the pivot point 3/4 from theheel edge of the door and 1-1/2 from the face of the edges must be beveled 1/8 in 2 .nFrame door stop must be provided at door closed door sizes greater than shown, consult us for in all standard architectural 203/4 Offset and1-1/2 OffsetFeaturesnExterior or interiordoors weight to 200 up to 3 6 x 7 0 nNon-hold open only nCast iron cement case nMaximum opening180 trim permittingnVertical door adjustment nAdjustable spring tension and closing speed nBuilt-in hydraulic backcheck cushions opening from140 to 180 nAvailable for Floor plate or threshold installation nStandard top pivot: 180 (3/4 offset)nRecommended intermediate pivot: M19 (3/4 offset)nANSI/C06042 nStandard spindle allows up to 3/4 door undercutnStandard offset 3/4.

5 Special offset 1-1/2 nDoor weight to 125 sizes up to 3 6 x 7 0 nBottom arm 1-1/2 offsetnStandard top pivot: 180 x 1-1/2 nRecommended intermediate pivot: M19 x 1-1/2 OptionsnCold weather fluid available for temperatures below -35 F.(specify CWF )nSealed closer available to prevent moisture from enteringcase Prefix SC nExtended spindles available in 1/2 increments up to 2 Specifications3/4 Offset1-1/2 OffsetOrdering InformationComplete 20 Series Closers include:3/4" OFFSET 1-1/2 OFFSETTop Pivot: 180180x1-1/2 Arm Package: 252050 252060(specify hand) Floor Plate: 204050204050 closer (less all parts): 20 20(specify hand)Cement Case: 203000203000 Options availableHeavy duty Pivot: H180H180x1-1/2 Intermediate Pivot: M19 M19x1-1/2 (specify hand)20 Series packageincludes.

6 closer , cementcase, Floor plate, armand shims, arm capand top plate installation shown16225 Series Offset Hung Floor Closers nAll offset hung Floor Closers are single acting and offset Floor Closers locate the pivot point 3/4 from theheel edge of the door and 3/4 from the face of the edges must be beveled 1/8 in 2 .n25 Series Closers have a built-in hydraulic backcheck to cushion the opening from 140 to 180 (not adjustable).nFrame door stop must be provided at door closed door sizes greater than shown below, consult us for suggested in all standard architectural 25 3/4 Offset nExterior or interior doorsweight to 350 up to 4 0 x 8 6 FeaturesnAvailable non-hold openor 180 automatic hold-open nCycolac cement case standardnMaximum opening 180 trim permittingnVertical door adjustment nAdjustable spring tension and closing speed nBuilt-in hydraulic backcheck cushions opening from 140 to 180 nStandard top pivot: 180nIntermediate pivot required nANSI/C06042 nStandard spindle allows up to 3/4 door weather fluid available for temperatures from 15 F to -35 F.

7 (Specify CWF )nSealed closer available to prevent moisture from enteringcase Prefix SC nExtended spindles available in l/2 increments up to 2 nAvailable for Floor plate or threshold installation Specifications3/4 OffsetOrdering InformationComplete 25 Series Closers include:Top Pivot:180 Arm Package:252050 (specify hand) Floor Plate:254050 closer (less all parts):25N (specify hand)Cement Case:253000 Options availableHeavy duty Pivot:H180 Metal Cement Case:253001 Intermediate Pivot:M19 (specify hand)RIXSONH eavy duty Floor ClosersToll Free: (800) 221-2052 nPhone: (718) 622-8785 or (516) 352-6262 nFax: (718) 789-8346 ne-mail: Series packageincludes: closer , cementcase, Floor plate, armand shims, arm capand top plate installation shown163 RIXSONH eavy duty Floor Closers27 Series Offset Hung Floor Closers nAll offset hung Floor Closers are single acting and offset Floor Closers locate the pivot point 3/4 from theheel edge of the door and 3/4 from the face of the offset Floor Closers locate the pivot point 3/4 from theheel edge of the door and 1-1/2 from the face of the edges must be beveled 1/8 in 2.

8 NFrame doorstop must be provided at door closed door sizes greater than shown, consult us for suggested 27 3/4 Offset nExterior or interior doorsweight to 450 up to 4 0 x 8 6 FeaturesnAvailable (NHO) non-holdopen, (AHO) automatic hold-open or (SHO) selectivehold-open at 85, 90, 95 or 105 nCycolac cement case standardnSeparate independent valves for closing, latch andbackcheck adjustments nBuilt-in positive dead stopprevents door from swinging beyond the desired opening degree nVertical door adjustment nAdjustable spring tension nStandard top pivot: 180nRecommended intermediate pivot: M19 nANSI C06041 nStandard spindle allows up to 3/4 door undercut nStandard offset 3/4 Special offset 1-1/2 nDoor weight to 200 sizes up to 4 0 x 8 6 nBottom arm 1-1/2 offsetnStandard top pivot: 180 x 1-1/2 nRecommended intermediate pivot: M19 x 1-1/2 OptionsnModels available to meet ANSI requirements for physi-cally handicapped access prefix PH nDelayed Action option available prefix DA nCold weather fluid available for temperatures from 15 F to -35 F.

9 (Specify CWF )nSealed closer available to prevent moisture from entering case Prefix SC nExtended spindles available in 1/2 increments up to 2 nAvailable for Floor plate or threshold application ( Floor plateshown) Specifications3/4 Offset1-1/2 OffsetOrdering InformationComplete 27 Series Closers include:3/4" OFFSET 1-1/2 OFFSETTop Pivot: 180180x1-1/2 Arm Package: 252050 252060(specify hand) Floor Plate: 274750274750(specify hand) closer (less all parts): 27-90N27-90N(specify hand)27-90S27-90S(specify hand)27-105N27-105N(specify hand)27-105S 27-105S(specify hand)Cement Case: 253000253000 Options availableHeavy duty Pivot: H180H180x1-1/2 Metal Cement Case: 253001253001 Intermediate Pivot: M19 M19x1-1/2 (specify hand)Model 27 3/4 OffsetModel 27 1-1/2 Offset27 Series package includes: closer , cement case, floorplate, arm and shims, armcap and top Series Offset Hung Floor Closers (Continued)nAll offset hung Floor Closers are single acting and offset Floor Closers locate the pivot point 3/4 from theheel edge of the door and 3/4 from the face of the edges must be beveled 1/8 in 2.

10 NFrame doorstop must be provided at door closed door sizes greater than shown, consult us for suggested L273/4 OffsetnLead lined doorsnWeight up to 1500 up to 4 0 x 8 6 FeaturesIdentical to Model 27 except:nCast iron cement case standardnDesigned for leadlined doors with lead in center of door(consult us when lead shielding is immediately behind face panel of door)nBottom arm features anti-friction bearing for greater loadcapacity nScrew holes in top pivot and bottom arm straddle lead lining nAvailable to accommodate door thicknesses 1-3/4 , 2 ,2-1/4 , 2-1/2 , or 3 nStandard top pivot: L180 nRecommended intermediate pivot: ML19nANSI/C06071n3/4 offset onlySpecificationsOrdering InformationComplete L27 Series Closers include:Top Pivot: L180 Arm Package: 252051 (specify hand) Floor Plate: 274750(specify hand) closer (less all parts): 27-90N (specify hand)27-90S(specify hand)27-105N(specify hand)27-105S(specify hand)Cement Case: 253001 Options availableIntermediate Pivot:ML19 (specify hand)RIXSONH eavy duty Floor ClosersToll Free: (800) 221-2052 nPhone: (718) 622-8785 or (516) 352-6262 nFax: (718) 789-8346 ne-mail: Series package includes: closer , cement case, floorplate, arm and shims, thrustbearing, arm cap and L180top duty Floor Closers26 Series Center Hung Floor Closersn26 Series Floor Closers are single acting and frame applied stop at 0 must be used to prevent closerfrom closing beyond 0.