Example: tourism industry

RM2652 RM2852 Installation & Operating Instructions

1 Installation & Operating INSTRUCTIONSRECORD THIS INFORMATION FOR FUTURE REFERENCEBEFORE INSTALLING THE UNIT:Model _____Serial Purchased_____ Place of Purchase_____! WARNINGI mproper Installation , adjustment,alteration, service or maintenancecan cause injury or property dam-age. Refer to this manual. For assis-tance or additional informationconsult a qualified installer, serviceagency or the gas supplier.! AVISCet appareil doit tre r par seulement par un r parateurautoris . Modification de l'appareilpourrait tre extr mementdangeruse, et pourrait causer malou OFFICEThe Dometic So. Poplar , IN 46761219-463-4858 CANADAD ometic Langs , OntarioCANADA N3H 2N7519-653-4390 For Service CenterAssistance Call:800-544-4881 INDEX 2 Operating 8 Maint.

The gas supply system must incorporate a pressure regu-lator to maintain a supply pressure of not more than 13-1/2 inches water column (static) no load. When testing the gas supply system at test pressures in excess of 1/2 psig, the refrigerator and its individual shutoff valve must be disconnected from the gas supply piping system. PRESSURE

Tags:

  System

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Other abuse

Transcription of RM2652 RM2852 Installation & Operating Instructions

1 1 Installation & Operating INSTRUCTIONSRECORD THIS INFORMATION FOR FUTURE REFERENCEBEFORE INSTALLING THE UNIT:Model _____Serial Purchased_____ Place of Purchase_____! WARNINGI mproper Installation , adjustment,alteration, service or maintenancecan cause injury or property dam-age. Refer to this manual. For assis-tance or additional informationconsult a qualified installer, serviceagency or the gas supplier.! AVISCet appareil doit tre r par seulement par un r parateurautoris . Modification de l'appareilpourrait tre extr mementdangeruse, et pourrait causer malou OFFICEThe Dometic So. Poplar , IN 46761219-463-4858 CANADAD ometic Langs , OntarioCANADA N3H 2N7519-653-4390 For Service CenterAssistance Call:800-544-4881 INDEX 2 Operating 8 Maint.

2 & INSTRUCTIONSREAD CAREFULLYFOR YOUR SAFETYIf you smell off gas supply at themain LP gas tank 't touch any open call your gassupplier or service YOUR SAFETYDo not store or use gasolineor other flammable vaporsand liquids in the vicinity ofthis or any other RM2652 & RM2852 REFRIGERATOR FOR LP/GASAND ELECTRIC OPERATIONForm No. 6/95 The Dometic , IN 46761 Copyright 1995 The Dometic Corporation1. GENERAL INSTRUCTIONSThis appliance is designed for storage of foods andstorage of frozen foods and making refrigerators outlined herein have been design certi-fied by under ANSI Z21 .19 Refrigerator Standardfor Installation in a mobile home or recreational vehicle andare approved by the Canadian Gas certifications are, however, contingent on theinstallation being made in accordance with the followinginstructions as the , the Installation must conform with:1.

3 National Fuel Gas Code ANSI (latest edition)2. Manufactured Home Construction and Safety Stan-dard, Title 24 CFR, Part 32803. Recreational Vehicles ANSI Al (latest edition).The unit must be electrically grounded in accordance withthe National Electric Code ANSI/NFPA 70-(latest edition)when installed if an external alternating current electricalsource is Any applicable local Canada, the Installation must conform with:1. Current CGA B 149 Gas Installation CSA Standard Z GAS-EQUIPPED REC-REATIONAL VEHICLES AND MOBILE HOUSING3. Any applicable local codeThe unit must be electrically grounded in accordance withthe CANADIAN ELECTRICAL CODE C 22 Parts 1 and VENTILATIONThe Installation shall be made in such a manner as toseparatethecombustion system from the living space of themobile home or recreational vehicle.

4 Louveropeningsforairsupply or for venting of combustion products shall have aminimum dimension of not less than 1/4 Installation requires one fresh air intake and oneupper exhaust vent. The ventilation kits shown in thisinstruction manual have been certified for use with therefrigerator model listed in the Table. For Certified VentSystem Kits see Section B. The ventilation kits must beinstalled and used without modification. An opening towardtheoutsideatfloor level in the refrigeratorcompartment mustbe provided forventilation of heavier-than-air fuel gases. Thelower vent of the recommended kits is provided with propersize openings. The flow of combustion and ventilation airmust not be lower side vent is fitted with a panel which provides anadequate access opening for ready serviceability of theburner and control manifold of the refrigerator.

5 This should becentered on the back of the CERTIFIED INSTALLATIONC ertified installations require one roof vent and one lowerside certified vent system kits, see Section further information, contact your dealer or METHOD OF INSTALLATIONThe method of Installation is shown in FIG. 1. It is essentialthat all maximum or minimum dimensions are strictly main-tained as the performanceof the refrigerator is dependent onadequate flow of air over the rear of the : The upper vent should becentered over the condenser coilat the back of the VENTILATION HEIGHTSR efer to FIG 1., Page 2 Installation with roofMinimum Ventilationvent and lower side ventheights in:REFRIGERATORINCHESMMRM265257-3/41465R M285263-3/41620 LOWER VENT CUTOUTUPPER VENT CUTOUT5-1/2"21-9/16"13-3/4"23-3/4"NOTE: All cutout dimensions are +/ 1/8".

6 6. CLEARANCESM inimum clearances in inches to combustible materials are:G:Top0"K:Side0"L:Bottom0"M:Rear0"N:S ee NOTENOTE: Clearance "M" is between the rearmost part of therefrigerator and the wall behind the : Clearance "N" is the distance between the bottomof the lower vent to the roof material. For ventilationheight, refer to Section A. Installation , Item 5. VentilationHeights. See FIGS. 1 & 2 FIG. 3 NOTE: Wood StripMUST be in PlaceRefrigeratorOverallRecessTotalModel DimensionsDimensionsRef. (Inches)(mm) RM2852 (Inches)(mm) REFRIGERATOR INENCLOSURENOTE: DO NOT install the appliance directly on must be removed or protected by a metal orwood panel beneath the appliance, which extends at leastthe full width and depth of the space between the counter, storage area or ceilingcan trap heat produced at the rear of the refrigerator.

7 Anyspace between the top and sides of the refrigerator shouldbe blocked for maximum refrigerator WATER DRAIN HOSE: A 3/4" hole mustbe drilled through the flooring in the opening of the baseplate on the rear of refrigerator (see FIG. 5D). The installermust make sure that the hose does not kink when runthrough the floor. Seal around the hose where it goesthrough the hole. If a longer hose is required, follow theillustration shown below:OPTION A:1) Remove black water check valve from ) Add additional hose3) Reinstall black water check valveOPTION B:1) Cut drain hose at location shown ) Install new drain hose between pieces : Black water check valve must be reinstalled toensure proper refrigerator operation. DO NOT KINK C:In vehicles where routing the drain hose through the flooris not possible, a metal clip is available.

8 The clip is used todrain water out through the side No. Clip for plastic side vent (Qty. 50)Part No. Clip for plastic side vent (Single)Part No. Clip for metal side vent (Qty. 50)Part No. Clip for metal side vent (Single) Installation : The refrigerator must be installed in asubstantial enclosure and must be level. When installingthe refrigerator in the enclosure, all areas within the recessin which the refrigerator is installed must be sealed. Makesure that there is a complete seal between the front frameof the refrigerator and the top, sides and bottom of theenclosure. A length of sealing strip is applied to the rearsurface of the front frame for this purpose. Also apply asealing strip to the foremost floor of the enclosure andapply a second sealing strip to the bottom of the trim stripon the front base as shown in FIG.

9 4. The sealing shouldprovide complete isolation of the appliance's combustionsystem from the vehicle wood strip must be in place across the upper opening ofthe enclosure. The top frame of the refrigerator will beanchored to the wood strip with screws. See FIG. dimensions shown in FIG. 3 will give you adequatespace for service and proper : If the door is hinged and it needs be changed to theopposite side, it must be done before the refrigerator isinstalled in the enclosure. See Step. : Be careful not to damage the sealing strip appliedto the floor of the enclosure when the refrigerator is put refrigerator is secured in the enclosure with six must be installed in the following order:a. First: Two screws are installed in front deco-ration strip and through the front ) The front strip is to be installed after the refrig-erator is set into the alcove.

10 The strip is shippedas a loose ) Install the lower front strip by sliding it under thebottom hinge plate as shown in FIG. 5. Thehinge plate can be on the right or left sidedepending on the door 4 FIG. 553)When the front strip is in place, install one screwthrough the hinge and into the floor. The secondscrew is installed with a washer on the oppositeside. (See FIG. 5A) : Install the two screws in the )The top decoration panel must be removedfrom the refrigerator before the screws can beinstalled. Open refrigerator door and gentlypush the tabs out of the hole in the hinge with flatblade screwdriver. See FIG. )Carefully tilt the top decoration panel and lift upto remove from top frame. See FIG. )Install the second two screws in the top frameas shown in FIG. 5 BFIG. 5A4)Replace the top decoration panel.