ROLLER PUMPS Form L-0100R - HYPRO PUMP

1 4- ROLLER PUMPSERIES 12006- ROLLER PUMPSERIES Rate: ..62 gpmMax. Pressure: ..150 psi :..1000 rpmPorts: ..1-1/2" NPT Inlet & OutletShaft: ..15/16" Dia. (Solid)Continuous psiIntermittent Rate: ..74 gpmMax. Pressure: ..150 psi :..800 rpmPorts: ..1-1/2" NPT Inlet & OutletShaft: ..1" Dia. (Solid)Continuous psiIntermittent psi5- ROLLER PUMPMax. Flow Rate: ..45 gpmMax. Pressure:.. 200 psi :..1000 rpmPorts:..1" NPT Inlet & " Hose Barb IncludedShaft:..15/16" Dia.(Solid)Continuous psiIntermittent psiSERIES 1700 Max.

2 Flow Rate: .. :..200 psi :..800 rpmPorts: ..3/4" NPT Inlet & " Hose Barb IncludedShaft:..15/16" Dia. (Solid)Continuous psiIntermittent psi7- ROLLER PUMPSERIES 7700 SERIES 75608- ROLLER PUMPMax. Flow Rate: ..22 :..300 psi :..1000 rpmPorts: ..3/4" NPT Inlet & " Hose Barb IncludedShaft:..15/16" Dia. (Solid)Continuous psiIntermittent psiMax. Flow Rate: ..22 :..300 :..1200 rpmPorts: ..3/4" NPT Inlet & " Hose Barb IncludedShaft:..5/8" Dia. (Solid)Continuous Op..100-150 psiIntermittent psiMax.

3 Flow Rate: ..9 gpm (4001)7 gpm (4101) :..150 psiMax. RPM: ..1800 rpm (4001)2600 rpm (4101)Ports: ..3/4" NPT Inlet & OutletShaft: ..5/8" Dia. (Solid)1/2" Dia.(Hollow)Continuous psiIntermittent psi6- ROLLER PUMPSERIES 6500 SERIES 4001 & 41014- ROLLER PUMP iron, Ni-Resist or the new SilverCast body and rotor, 416stainless steel shaft, sealed factory-lubricated ballbearings, cartridge-type lip seals of Viton, Buna-N orleather, and versatile Super Rollers. (Super Rollers featurethe life of polypropylene and the chemical resistance ofnylon.)

4 Rotation for all models is counterclockwise for easytractor PTO drive, except models 4001 and 4101 which areclockwise. PUMPS are available in reverse ROLLER PUMPS are designed for agricultural andindustrial spraying and transfer of a variety fluids. Theseinclude insecticides, herbicides, emulsives, aromaticsolvents, liquid fertilizers and many other liquids. Theeconomical rotary-action ROLLER principle requires no checkvalves while providing positive displacementcharacteristics with less friction and lower starting torquethan other PUMPS .

5 Construction features include a cast- ROLLER PUMPS OUTIN OUTIN Installation,Operation, Repair and Parts Manual10-04 DescriptionForm L-0100 RIt is permissible to mount the torque arm with the chain inthe down position. To do this, mount the arm to the pump inthe reverse not use the tension spring or : Do not attach torque arm to movable certain that the power source conforms to therequirements of your adequate protection in guarding around themoving parts such as the shaft and Disconnect power before Release all pressure within the system before servicingany Drain all liquids from the system before servicing Check all hoses for weak or worn condition before eachuse.

6 Make certain that all connections are tight Periodically inspect the pump and the systemcomponents. Perform routine maintenance as required(see Maintenance section).14. Never operate a gasoline engine in an enclosed sure the area is well Use only pipe, hose and fittings rated for the maximumpsi rating of the Never use these PUMPS for pumping water or otherliquids for human or animal a Pressure Relief Device on the discharge sideof the Pump to prevent damage from pressurebuildup when the pump discharge is blocked orotherwise closed and the power source is.

7 Never pump flammable or explosivefluids such as gasoline, fuel oil, kerosene, etc. Neveruse in explosive atmospheres. The Pump should beused only with liquids compatible with the Pumpcomponent materials. Failure to follow this warningcan result in personal injury and/or propertydamage and will void the product pump acids ( acid fertilizer) with SuperRollers! When pumping acidic fertilizer, Hyprorecommends only the Silver Series castings and Teflonrollers, or use one of HYPRO 's poly centrifugal Never run the pump faster than maximumrecommended Never pump at pressures higher than the maximumrecommended Never pump liquids at temperatures higher than therecommended maximum temperatures (140 F / 60 C).

8 Engine for additional information. Read all safety informationbefore attempting to install or operate the manual will cover the installation of the basic driveconfigurations available for HYPRO ROLLER PUMPS . Consult therecommendations of the manufacturer of your motor orThe preferred method for mounting the torque arm andpump to a tractor is with the chains going up to providesupport for the pump (see Figure 1).Attach the torque armto the pump with the long side of the arm on the inlet side ofthe pump for this type of tractors do nothave easy attachment points for securing the tension andtorque chains.

9 It may be necessary to drill holes in thetractor's master shield to attach the is also acceptable to mount an angle iron on the mastershield to attach the chains. The chains should be attached tothe tractor as close to vertical as possible to avoid a bendingforce on the the pump and torque arm to the PTO shaft usinga HYPRO series 1320, 1321 or 1323 Attach the torque chain to the tractor frame with arm inhorizontal Attach the tensioning chain to the tractor frame whileapplying tension to the Safety InformationDrive Source InstallationTractor PTO InstallationFigure 6 Figure 7 Figure 5 Push the belt midway between the pulleys.

10 Check the deflection (d) and adjust:d = x L==Belt and pulley drive systems are typically used to reducepump speed. For determining proper pulley sizes, use theformula below as a guideline and use A or B RPM FLOW (@ RATED SPEED)PUMP PULLEY RPMFLOW (DESIRED)MOTOR PULLEY : Use a 1725 RPM electric motor to drive a pump at 950 , a pulley diameter on the motor is inches. Thepump pulley diameter can be determined from the formulaabove:1725 PUMP PULLEY INCHES1725X INCHES = INCHES9501.