ROUGH TERRAIN CRANE - KATO WORKS

1 1 SPECIFICATION CRANED escriptionRough TERRAIN CRANE with maximum lifting capacity 25 ton CRANE Specifi cationMaximum rated lifting capacity m Boom 25,000kg (Parts of line : 7) m Boom 19,000kg (Parts of line : 6) m Boom 12,500kg (Parts of line : 4) m Boom 8,000kg (Parts of line : 4) m Jib 3,300kg 75 (Parts of line : 1) m Jib 2,100kg 73 (Parts of line : 1)Rooster 4,000kg (Parts of line : 1)Boom jib length rated lifting (Boom) (jib)Hoisting line speed(winch up)Main winch125m / min. (at 4th layer)Auxiliary winch125m / min. (at 4th layer)Hoisting hook speed(winch up)Main winch(Parts of line; 7) : / min. (at 4th layer)Auxiliary winch(Parts of line; 1) : / min. (at 4th layer)High-speed loweringRope speedMain winchReference value with no load at 163m / min.

2 (at 4th layer)Auxiliary winchBoom derricking angle0 83 Boom derricking time40s / 0 83 Boom extending / 93sSlewing i l s l e w i n g r a d i u s3 ,10 0 m m Equipment and structureBoom typeBox-shaped, 4-section hydraulically telescopic type(Boom section 3 / 4 simultaneously operated)Jib type2 sections (2nd section of draw-out type)Hydraulic stepless tilting type (offset angles 5 60 )Boom extension/retraction equipmentTwo hydraulic cylinders and wire ropes used togetherBoom derricking/lowering equipmentOne hydraulic cylinder of direct acting type with pressure-compensated fl ow control valveWinch system Main & Auxiliary winchesTwo units of Single winch Equipped with Hydraulic motor drive and Planetary gear speed reducer (built-in negative brake), High/Low speed switching system and Hydraulic compensated fl ow control equipmentEquipped with Hydraulic motor drive and a planetary gear speed reducer (built-in negative brake) Free/Lock change-over modelSlewing bearingBall bearing typeOutriggers TypeHydraulic H-beam type (with fl oat and vertical cylinder in single unit)Extension width6,600mm (Fully extended)6,000mm (Intermediately extended)5,000mm (Intermediately extended)3,800mm (Intermediately extended)2,310mm (Fully retracted)Wire rope for hoistingMain winchDiameter: 16mm Length: 175mAuxiliary winchDiameter: 16mm Length.

3 95m Hydraulic equipmentOil pumpDouble variable plunger type, gear and plunger type Hydraulic motorHoisting motorAxial plunger typeSlewing motorAxial plunger typeControl valveDouble acting with integral check and relief valves (With Hydraulic compensated fl ow control valve)CylinderDouble acting typeOil reservoir capacity500L Safety devicesACS (Automatic CRANE System with Voice alarm), Slewing automatic stop system, Boom raise / lower dampening function, Boom extension / retraction dampening function, Working range limit mode, Outrigger status detector, Boom derricking / telescoping holding valve, Jib derricking holding valve, Overhoist prevention device, Winch holding valve, Automatic winch brake, Winch drum roller, Hydraulic safety valves, Outrigger lock pins, Slewing lock, Slewing warning lamp, Hydraulic oil temperature warning device, Hydraulic oil return fi lter warning device Standard equipmentAir conditioner(with cold/warm box), Hydraulic oil cooler, Working light (on boom, table and cab)

4 , Winch drum turning indication device, Hook for 25 ton, Hook for 4 ton Operator's cabHydraulic cab suspension, Adjustable steering wheel, Adjustable suspension seat, Power Window(external closing switch), Front windscreen wiper & washer (2 speed wiper), Roof window wiper & washer, Tea table, Cigarette lighter, Access step light, Floor mat, AM/FM Radio, Hot and cool box Optional equipmentACS outside indicator, PA system, Door visor, Anemometer, Winch view camera CARRIER Carrier Specifi cationMaximum traveling speed 49km/hGrade (tan )Minimum turning radius(center of extreme outer tire) (2 wheel steer) (4 wheel steer) EngineModelMitsubishi 6M60-TLE3A (with Intercooled turbocharger)Type4 cycle, 6 cylinders, water cooled, direct injection turbo-charged diesel engine with intercoolingPiston power200kW at 2,600min-1 Max.

5 Torque785N m at 1,400min-1 Equipment and structureDrive systemSwitches between 2 wheel drive (4x2) and 4 wheel drive (4x4)To r q u e c o n v e r t e rEngine mounted 3 elements1 stage (with lock up clutch)TransmissionRemote mounted full automatic Number of speeds4 forward & 1 reverse speed (with HI - Low selector)AxlesFront Full fl oating type, with a two-stage reduction gearRear Full fl oating type, with a two-stage reduction gearSuspensionFrontTaper - leaf spring (hydraulic locking device with shock absorber)RearTaper - leaf spring (hydraulic locking device with shock absorber)Brake systemServiceAir-over hydraulic disk brake on 4 wheels(front and rear independent circuit)ParkingSpring applied, electrically air released parking brake mounted on front axle, internal expanding typeAuxiliaryExhaust brake (electronically controlled torque convertor interlocking)Eddy current type retarder, Auxiliary braking unit for working SteeringModelAll hydraulic power steering with reverse steering correction systemModeFront 2 wheel steering, counter steering, crab steering, rear 2 wheel steering, independent front and rear wheel steering (5 modes) (with automatic rear steering lock system)Tire sizeFront385 / 95 R25 170E ROADRear385 / 95 R25 170E ROADFuel tank capacity300 LBatteries(12V-120AH) 2 Safety devicesEmergency steering device, Rear wheel steering lock system (automatic)

6 , Miss-shifting prevention system, Brake fl uid leak warning device, Service brake lock, Suspension lock, Engine overspeed alarm, Radiator coolant level warning device, Electrically stowed side mirrors, Mirror on the right side of the boom, Rearview camera and color monitor, Air fi lter service warning device Standard equipmentCentralized lubricating system Optional equipmentRight side view camera, Left side view camera, Wheel stopper,Way side lamp, Side marker lamp GENERAL DimensionsOverall length11,565mmOverall width 2,620mmOverall height 3,475mmWheel base 3,650mmTreadsFront 2,170mmRear 2,170mmPassenger capacityOne personGross vehicle massGross weightapprox. 26,495kgFront weightapprox. 13,180kgRear weightapprox. 13,315kg Stow the hooks in place before traveling.

7 Before you use this machine, read the precautions in the instruction manual thoroughly to operate it correctly. KATO products and specifi cations are subject to improvements and changes without TERRAIN CRANE2 RATED LIFTING CAPACITY( ) ( )( )( )( )Workingradius (m)Outriggers fully extended (360 full range)Outriggers intermediately extended (over side)Outriggers intermediately extended (over side)Outriggers intermediately extended (over side)Outriggers completely retracted (over side) boom angle 35 34 46 41 56 65 Standard hookfor 25 tonfor 25 tonfor 25 tonfor 25 tonfor 25 tonHook mass220kg220kg220kg220kg220kgParts of line76447644764476447644(Unit : Metric ton) Boom511-74301002 Based on ISO 4305 Not exceed 75% of static tipping Boom Boom Boom Boom Jib ( ) ( ) ( )Outriggers fully extended (360 full range)Outriggers intermediately extended (over side)Outriggers intermediately extended (over side)Boom angle( )Offset 5 Offset 25 Offset 45 Offset 60 Boom angle( )Offset 5 Offset 25 Offset 45 Offset 60 Boom angle( )Offset 5 Offset 25 Offset 45 Offset 60 Workingradius (m)Load(ton)Workingradius (m)Load(ton)Workingradius (m)Load(ton)Workingradius (m)Load(ton)Workingradius (m)Load(ton)Workingradius (m)Load(ton)Workingradius (m)Load(ton)Workingradius (m)Load(ton)Workingradius (m)Load(ton)Workingradius (m)Load(ton)Workingradius (m)Load(ton)Workingradius (m)Load(ton)

8 Boom angle52 52 52 61 hookfor 4 boom angle44 44 45 61 Hook mass60kgCritical boom angle39 39 45 61 Standard hookfor 4 tonParts of line1 Standard hookfor 4 tonHook mass60kgHook mass60kgParts of line1 Parts of line1 ( )Outriggers intermediately extended (over side)Boom angle( )Offset 5 Offset 25 Offset 45 Offset 60 Workingradius (m)Load(ton)Workingradius (m)Load(ton)Workingradius (m)Load(ton)Workingradius (m)Load(ton)

9 Boom angle61 61 61 61 Standard hookfor 4 tonHook mass60kgParts of line1 ( ) ( )Outriggers fully extended (360 full range) Outriggers intermediately extended (over side)Boom angle( )Offset 5 Offset 25 Offset 45 Offset 60 Boom angle( )Offset 5 Offset 25 Offset 45 Offset 60 Workingradius (m)Load(ton)Workingradius (m)Load(ton)Workingradius (m)Load(ton)Workingradius (m)Load(ton)Workingradius (m)Load(ton)Workingradius (m)Load(ton)Workingradius (m)Load(ton)Workingradius (m)Load(ton) boom angle47 47 47 61 Critical boom angle42 42 45 61 Standard hookfor 4 tonStandard hookfor 4 tonHook mass60kgHook mass60kgParts of line1 Parts of line1 ( ) ( )

10 Outriggers intermediately extended (over side)Outriggers intermediately extended (over side)Boom angle( )Offset 5 Offset 25 Offset 45 Offset 60 Boom angle( )Offset 5 Offset 25 Offset 45 Offset 60 Workingradius (m)Load(ton)Workingradius (m)Load(ton)Workingradius (m)Load(ton)Workingradius (m)Load(ton)Workingradius (m)Load(ton)Workingradius (m)Load(ton)Workingradius (m)Load(ton)Workingradius (m)Load(ton) boom angle63 63 63 63 hookfor 4 tonCritical boom angle54 54 54 61 Hook mass60kgStandard hookfor 4 tonParts of line1 Hook mass60kgParts of line1511-743020025 60 5 60 Based on ISO 4305 Not exceed 75% of static tipping loads511-743020024 When the outriggers are not usedBased on ISO 4305 Not exceed 75% of static tipping loadsWorkingradius (m)