SABIC Polyether Imide ULTEM™ Resin 1000 - Americas

1 ULTEM Resin 1000 - AmericasPolyether DataProduct DescriptionULTEM 1000 Resin is an amorphous, transparent polyetherimide (PEI) plastic offering a glass transition temperature (Tg) of 217 C. Thisinherently flame retardant Resin has UL94 V0, V2 and 5VA ratings and is RoHS compliant. ULTEM 1000 Resin is an unreinforced general purposegrade offering high heat resistance, high strength and modulus and broad chemical resistance up to high Status Commercial: ActiveLiterature 1 Technical DatasheetUL Yellow Card 2 E121562-101048254 Search for UL Yellow Card SABIC ULTEM ResinAvailability Latin America North AmericaFeatures Amorphous Chemical Resistant Flame Retardant General Purpose High Heat Resistance High StrengthUses Additive Manufacturing (3 DPrinting)

2 Aerospace Applications Appliances Automotive Applications Automotive Exterior Parts Automotive Interior Parts Automotive Lighting Automotive Under the Hood Construction Applications Electrical/ElectronicApplications Electronic Displays Fluid Handling Industrial Applications Lawn and Garden Equipment Lenses Lighting Applications Medical/HealthcareApplications Non-specific Food Applications Oil/Gas Applications Outdoor Applications Pharmaceuticals Rail ApplicationsAutomotive Specifications FORD WSK-M4D716-AAppearance Clear/TransparentProcessing Method Extrusion Blow Molding Injection MoldingMulti-Point Data Coefficient of Thermal Expansion vs.

3 Temperature (ASTM E831) Compressive Stress vs. Strain (ASTM D695) Elastic Modulus vs Temperature (ASTM D4065) Flexural DMA (ASTM D4065) Instrumented Impact (Energy) (ASTM D3763) Instrumented Impact (Load) (ASTM D3763) Pressure-Volume-Temperature (PVT - Zoller Method) Shear DMA (ASTM D4065) Specific Heat vs. Temperature (ASTM D3417) Tensile Creep (ASTM D2990) Tensile Fatigue Tensile Stress vs. Strain (ASTM D638) Thermal Conductivity vs. Temperature (ASTM E1530) Viscosity vs. Shear Rate (ASTM D3835)Also Available In Asia Pacific EuropePhysicalNominal Value(English)Nominal Value(SI)Test MethodDensity / Specific ASTM D792 Melt Mass-Flow Rate (MFR) (337 kg) minASTM D1238 Molding Shrinkage - Flow ( in ( mm)) to to MethodWater AbsorptionASTM D57024 , 73 F (23 C) of 18 Form No.

4 TDS-4195-enUL and the UL logo are trademarks of UL LLC 2018. All Rights Prospector | 800-788-4668 or 307-742-9227 | information presented here was acquired by UL from the producer of the product or material or original information provider. However, ULassumes no responsibility or liability for the accuracy of the information contained on this website and strongly encourages that upon final productor material selection information is validated with the manufacturer. This website provides links to other websites owned by third parties. Thecontent of such third party sites is not within our control, and we cannot and will not take responsibility for the information or Created: Thursday, May 3, 2018 Added to Prospector: November 2000 Last Updated.

5 4/11/2018 ULTEM Resin 1000 - AmericasPolyether MechanicalNominal Value(English)Nominal Value(SI)Test MethodTensile Modulus 4519000psi3580 MPaASTM D638 Tensile Strength 5 (Yield)16000psi110 MPaASTM D638 Tensile Elongation 5 ASTM Modulus 6 ( in (100 mm) Span)509000psi3510 MPaASTM D790 Flexural Strength 6 ASTM D790 Yield, in (100 mm) Span23900psi165 MPaPoisson's ASTM E132 Taber Abrasion ResistanceASTM D10441000 Cycles, 1000 g, CS-17 Value(English)Nominal Value(SI)Test MethodNotched Izod Impact (73 F (23 C)) lb/in53J/mASTM D256 Unnotched Izod Impact (73 F (23 C))25ft lb/in1300J/mASTM D4812 Reverse Notch Izod ImpactASTM in ( mm)25ft lb/in1300J/mGardner Impact (73 F (23 C))319in D3029 HardnessNominal Value(English)Nominal Value(SI)Test MethodRockwell Hardness (M-Scale)109 109 ASTM D785 ThermalNominal Value(English)Nominal Value(SI)Test MethodDeflection Temperature Under LoadASTM D64866 psi ( MPa), Unannealed, in ( )410 F210 C264 psi ( MPa), Unannealed, in ( )394 F201 CVicat Softening Temperature424 F218 CASTM D1525 7 CLTEASTM E831 Flow : -4 to 302 F (-20 to 150 C) CTransverse.

6 -4 to 302 F (-20 to 150 C) CThermal in/hr/ft / C177 RTI Elec338 F170 CUL 746 RTI Imp338 F170 CUL 746 RTI Str338 F170 CUL 746 ElectricalNominal Value(English)Nominal Value(SI)Test MethodVolume +17ohms +17ohms cmASTM D257 Dielectric StrengthASTM in ( mm), in Air830V/mil33 in ( mm), in Oil710V/mil28 in ( mm), in Oil500V/mil20kV/mmDielectric ConstantASTM D150100 1 Dissipation FactorASTM D150100 1 Arc Resistance 8 PLC 5 PLC 5 ASTM D495 Comparative Tracking Index (CTI)PLC 4 PLC 4 UL 746 High Amp Arc Ignition (HAI) 9 PLC 3 PLC 3 UL 746 High Voltage Arc Tracking Rate (HVTR)PLC 2 PLC 2 UL 746 Hot-wire Ignition (HWI)PLC 1 PLC 1 UL 7462 of 18 Form No.

7 TDS-4195-enUL and the UL logo are trademarks of UL LLC 2018. All Rights Prospector | 800-788-4668 or 307-742-9227 | information presented here was acquired by UL from the producer of the product or material or original information provider. However, ULassumes no responsibility or liability for the accuracy of the information contained on this website and strongly encourages that upon final productor material selection information is validated with the manufacturer. This website provides links to other websites owned by third parties. Thecontent of such third party sites is not within our control, and we cannot and will not take responsibility for the information or Created: Thursday, May 3, 2018 Added to Prospector: November 2000 Last Updated.

8 4/11/2018 ULTEM Resin 1000 - AmericasPolyether FlammabilityNominal Value(English)Nominal Value(SI)Test MethodFlame RatingUL in ( mm)V-2 V-2 in ( mm)V-0 V-0 in ( mm)5VA 5VA Oxygen Index47%47%ASTM D2863 NBS Smoke Density - Flaming, Ds ASTM E662 InjectionNominal Value(English)Nominal Value(SI)Drying Temperature302 F150 C Drying to to Suggested Max Suggested Shot Size40 to 60%40 to 60% Rear Temperature626 to 752 F330 to 400 C Middle Temperature644 to 752 F340 to 400 C Front Temperature653 to 752 F345 to 400 C Nozzle Temperature653 to 752 F345 to 400 C Processing (Melt) Temp662 to 752 F350 to 400 C Mold Temperature275 to 329 F135 to 165 C Back to to Screw Speed40 to 70rpm40 to 70rpm Vent to to Injection NotesInjection Molding Parameters Drying Time (Cumulative): 24 hrsExtrusion NotesExtrusion Blow Molding Parameters Drying Temperature: 140 to 150 C Drying Time: 4 to 6 hrs Drying Time (Cumulative): 24 hrs Maximum Moisture Content: to Melt Temperature (Parison): 320 to 355 C Barrel - Zone 1 Temperature: 325 to 350 C Barrel - Zone 2 Temperature: 330 to 355 C Barrel - Zone 3 Temperature: 330 to 355 C Barrel - Zone 4 Temperature: 330 to 355 C Adapter - Zone 5 Temperature.

9 330 to 355 C Head - Zone 6 - Top Temperature: 330 to 355 C Head - Zone 7 - Bottom Temperature: 330 to 355 C Screw Speed: 10 to 70 rpm Mold Temperature: 65 to 175 C Die Temperature: 325 to 355 C3 of 18 Form No. TDS-4195-enUL and the UL logo are trademarks of UL LLC 2018. All Rights Prospector | 800-788-4668 or 307-742-9227 | information presented here was acquired by UL from the producer of the product or material or original information provider. However, ULassumes no responsibility or liability for the accuracy of the information contained on this website and strongly encourages that upon final productor material selection information is validated with the manufacturer.

10 This website provides links to other websites owned by third parties. Thecontent of such third party sites is not within our control, and we cannot and will not take responsibility for the information or Created: Thursday, May 3, 2018 Added to Prospector: November 2000 Last Updated: 4/11/2018 ULTEM Resin 1000 - AmericasPolyether Coefficient of Thermal Expansion vs. Temperature (ASTM E831) Thermal Expansion (in^-5/in/ F)-1000100200300400 Temperature ( F)FLOWCROSSFLOW4 of 18 Form No. TDS-4195-enUL and the UL logo are trademarks of UL LLC 2018. All Rights Prospector | 800-788-4668 or 307-742-9227 | information presented here was acquired by UL from the producer of the product or material or original information provider.