Safety Data Sheet - epicorinc.com

1 Safety Data Sheet Product Name: SBA-OH RESIN NUCLEAR GRADE Issue Date: 10/11/2015 Page 1 of 7 May be used to comply with OSHA s Hazard Communication Standard, 29 CFR 1910, 1200. Standard must be consulted for specific requirements. 1. Chemical Product and Company Identification SBA-OH RESIN NUCLEAR GRADE COMPANY IDENTIFICATION Epicor, Incorporated 1414 East Linden Avenue Linden, New Jersey 07036 Fax: (908) 925-7795 E-mail: 24-HOUR EMERGENCY TELEPHONE NUMBER (908) 925-0800 2. Hazards Identification Hazard Classification This material is hazardous under the criteria of the Federal OSHA Hazard Communication Standard 29 CFR Serious eye damage Category 1 Label elements Hazard pictograms Signal word: DANGER! Hazards Causes serious eye damage Product Name: SBA-OH RESIN NUCLEAR GRADE Issue Date: 10/11/2015 Page 2 of 7 Precautionary statements Prevention Wear eye protection/face protection Response IF IN EYES: Rinse cautiously with water for several minutes.

2 Remove contact lenses, if present and easy to do. Continue rinsing. Immediately call a POISON CENTER or doctor/physician. 3. Composition Information Component CAS # Styrene / Divinylbenzene Anion Exchange Resin Hydroxide Ion Form 069011-18-3 Water 7732-18-5 4. First-aid Measures Eye Contact: Wash immediately and continuously with flowing water for at least 30 minutes. Remove contact lenses after the first 5 minutes and continue washing. Obtain prompt medical consultation, preferably from an ophthalmologist. Eye wash fountain should be located in immediate work area. Skin Contact: Wash skin with plenty of water. Inhalation: Move person to fresh air; if effects occur, consult a physician. Ingestion: No emergency medical treatment necessary. Notes to Physician: Chemical eye burns may require extended irrigation.

3 Obtain prompt consultation, preferably from an ophthalmologist. No specific antidote. Treatment of exposure should be directed at the control of symptoms and the clinical condition of the patient. Emergency Personnel Protection: First Aid responders should pay attention to self-protection and use the recommended protective clothing (chemical resistant gloves, splash protection). If potential for exposure exists refer to Section 8 for specific personal protective equipment. 5. Fire Fighting Measures Extinguishing Media: Water. Dry chemical fire extinguishers. Carbon dioxide fire extinguishers. Fire Fighting Procedures: Keep people away. Isolate fire and deny unnecessary entry. Soak thoroughly with water to cool and prevent re-ignition. Cool surroundings with water to localize fire zone. Special Protective Equipment for Firefighters: Wear positive-pressure self-contained breathing apparatus (SCBA) and protective fire fighting clothing (includes fire fighting helmet, coat, trousers, boots, and gloves).

4 If protective equipment is not available or not used, fight fire from a protected location or safe distance. Unusual Fire and Explosion Hazards: This material will not burn until the water has evaporated. Residue can burn. Hazardous Combustion Products: Under fire conditions some components of this product may decompose. The smoke may contain unidentified toxic and/or irritating compounds. Product Name: SBA-OH RESIN NUCLEAR GRADE Issue Date: 10/11/2015 Page 3 of 7 Combustion products may include and are not limited to: Organic amines. Nitrogen oxides. Hydrocarbons. Carbon monoxide. Carbon dioxide. Benzene compounds. 6. Accidental Release Measures Steps to be Taken if Material is Released or Spilled: Contain spilled material if possible. Sweep up. Recover spilled material if possible. Collect in suitable and properly labeled containers.

5 See Section 13, Disposal Considerations, for additional information. Personal Precautions: Only trained and properly protected personnel must be involved in clean-up operations. Spilled material may cause a slipping hazard. Ventilate area of leak or spill. Refer to Section 7, Handling, for additional precautionary measures. Use appropriate Safety equipment. For additional information, refer to Section 8, Exposure Controls and Personal Protection. Environmental Precautions: Prevent from entering into soil, ditches, sewers, waterways and/or groundwater. See Section 12, Ecological Information. 7. Handling and Storage Handling General Handling: Do not get in eyes. Wash thoroughly after handling. Keep container closed. Use with adequate ventilation. Static electricity can accumulate on dry beads. Leave room for expansion as dry resin swells upon wetting and/or changing ionic form.

6 Equipment construction material should be compatible with feed, regenerant, ionic form and effluent of the ion exchange process. Avoid generating and breathing dust. Good housekeeping and controlling of dusts are necessary for safe handling of product. See Section 8, EXPOSURE CONTROLS AND PERSONAL PROTECTION. Storage Store in a dry place. Keep container tightly closed when not in use. Preferred storage temperature is in the lower half of the range given below. Shelf life: Use within shelf life date specified on product label. Storage temperature: 0 - 50 C 8. Exposure Controls / Personal Protection Exposure Limits None established Personal Protection Eye/Face Protection: Chemical goggles are preferred unless it is felt that Safety glasses with side shields would be an adequate Safety measure in the handling process.

7 Product Name: SBA-OH RESIN NUCLEAR GRADE Issue Date: 10/11/2015 Page 4 of 7 Skin Protection: Wear clean, body-covering clothing. Hand protection: Use gloves chemically resistant to this material when prolonged or frequently repeated contact could occur. Examples of preferred glove barrier materials include: Neoprene. Nitrile/butadiene rubber ("nitrile" or "NBR"). Polyvinyl chloride ("PVC" or "vinyl"). Avoid gloves made of: Polyvinyl alcohol ("PVA"). NOTICE: The selection of a specific glove for a particular application and duration of use in a workplace should also take into account all relevant workplace factors such as, but not limited to: Other chemicals which may be handled, physical requirements (cut/puncture protection, dexterity, thermal protection), potential body reactions to glove materials, as well as the instructions/specifications provided by the glove supplier.

8 Respiratory Protection: Under intended handling conditions, no respiratory protection should be needed. Ingestion: Use good personal hygiene. Do not consume or store food in the work area. Wash hands before smoking or eating. Engineering Controls Ventilation: Use local exhaust ventilation, or other engineering controls to maintain airborne levels below exposure limit requirements or guidelines. If there are no applicable exposure limit requirements or guidelines, general ventilation should be sufficient for most operations. 9. Physical and Chemical Properties Physical State Beads pH Color Yellow to brown Odor Amine Vapor Pressure (mm Hg) 17 at 20 C / 68 F Vapor Density (Air = 1) Less than 1 Boiling Point 100 C / 212 F Solubility in Water Negligible Specific Gravity Melting Point 0 C 32 F (water) Evaporation Rate Less than 1 (water) 10.

9 Stability and Reactivity Stability/Instability Stable under recommended storage conditions. See Storage, Section 7. Conditions to Avoid: Exposure to elevated temperatures can cause product to decompose. Incompatible Materials: Avoid contact with oxidizing materials. Oxidizing agents such as nitric acid attack organic exchange resins under certain conditions. Before using strong oxidizing agents, consult sources knowledgeable in handling such materials. The severity of the reaction with oxidizing materials can vary from slight degradation to an explosive reaction. Hazardous Polymerization Will not occur. Thermal Decomposition Product Name: SBA-OH RESIN NUCLEAR GRADE Issue Date: 10/11/2015 Page 5 of 7 Decomposition products depend upon temperature, air supply and the presence of other materials. Decomposition products can include and are not limited to: Aromatic compounds.

10 Hydrocarbons. Organic amines. 11. Toxicological Information Acute Toxicity Ingestion LD50, Rat > 5,000 mg/kg Skin Absorption The dermal LD50 has not been determined. Repeated Dose Toxicity No relevant information found. Chronic Toxicity and Carcinogenicity No relevant information found. Developmental Toxicity No relevant information found. Reproductive Toxicity No relevant information found. Genetic Toxicology No relevant information found. 12. Ecological Information ENVIRONMENTAL FATE Movement & Partitioning No bioconcentration of the polymeric component is expected because of its high molecular weight. In the terrestrial environment, material is expected to remain in the soil. In the aquatic environment, material will sink and remain in the sediment. Persistence and Degradability Surface photodegradation is expected with exposure to sunlight.