Safety Data Sheet - evercoat.com

1 Safety data SheetStock Number:Revision Date:Replaces:10070906-20-201701-20-2017 Slick Sand1. Identification Product identifier used on the label: Slick SandStock Number: 100709 Other means of identification: Synonyms: None KnownRecommended use of the chemical and restrictions on use: Recommended use: Polyester Primer SurfacerRestrictions on use: Uses other than recommended , address, and telephone number of the chemical manufacturer, importer, or other responsible party: ITW Evercoata division of Illinois Tool Works Cornell RoadCincinnati, OH 45242513-489-7600 Telephone number: CHEMTREC: 1-800-424-9300 CANUTEC: 1-613-996-6666 Emergency phone number: CHEMTREC: 1-800-424-9300 CANUTEC: 1-613-996-6666 2. Hazard(s) identification Classification of the chemical in accordance with paragraph (d) of :GHS Hazard Symbols:GHS Classification:Skin Sensitisation Category 1 Germ Cell Mutagenicity Category 1 BCarcinogenicity Category 1 ASpecific Target Organ Systemic Toxicity (STOT) - Single Exposure Category 1 Specific Target Organ Systemic Toxicity (STOT) - Repeated Exposure Category 1 Aspiration Hazard Category 1 Flammable Liquid Category 2 Skin Corrosion/Irritation Category 2 Serious Eye Damage/Eye Irritation Category 2 AReproductive Toxicity Category 2 Safety data SheetProduct identifier used on the label: Slick SandStock Number: 100709 Revision Date: 06-20-2017 Replaces: 01-20-2017 Page 2 of 14 Hazardous to the aquatic environment - Acute Category 2 Signal Word:DangerHazard Statements.

2 Highly flammable liquid and be fatal if swallowed and enters skin cause an allergic skin serious eye cause genetic cause of damaging fertility or the unborn damage to damage to organs through prolonged or repeated to aquatic Statements:Prevention:Obtain special instructions before not handle until all Safety precautions have been read and away from heat/sparks/open flames/hot surfaces. No container tightly container and receiving explosion-proof electrical/ventilating/lighting only non-sparking precautionary measures against static not breathe dust/fume/gas/mist/ with soap and water thoroughly after not eat, drink or smoke when using this work clothing must not be allowed out of the release to the protective gloves/protective clothing/eye protection/face :If swallowed: Immediately call a poison ON SKIN: Wash with plenty of soap and on skin (or hair): Take off immediately all contaminated clothing.

3 Rinse skin with IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue treatment (see Sections 4 to 8 on the SDS and any additional information on the label).Do NOT induce skin irritation or rash occurs: Get medical data SheetProduct identifier used on the label: Slick SandStock Number: 100709 Revision Date: 06-20-2017 Replaces: 01-20-2017 Page 3 of 14If eye irritation persists: Get medical off contaminated clothing and wash it before case of fire: Use appropriate media to :Keep container tightly closed. Store in a well-ventilated place. Keep cool. Store locked :Dispose of contents in accordance with your local disposal company along with national/international not otherwise classified: Reports have associated repeated and prolonged occupational overexposure to solvents with permanent brain and nervous system damage. 3. Composition/information on ingredients Chemical Name Common name and synonyms CAS # %BenzeneNone Known71-43-2< Known108-88-3< Hydrocarbons (stoddard type)None Known64742-48-9< Silica (Quartz)None - 1 Naphtha, Petroleum, heavy alkylateNone - 1 Titanium dioxideNone - triacrylateNone Known15625-89-51 - 5 AcetoneNone Known67-64-110 - 30 StyreneNone Known100-42-510 - 30 TalcNone Known14807-96-610 - 30 One or more hazardous ingredient(s) is claimed as a trade secret under the OSHA Hazard Communication Standard.

4 The hazards of this (these) ingredient(s) are given on this SDS. 4. First-aid measures Description of necessary measures, subdivided according to the different routes of exposure, , inhalation, skin and eye contact, and ingestion: Inhalation: Remove to fresh air. If breathing is difficult, have a trained individual administer oxygen. If not breathing, give artificial respiration and have a trained individual administer oxygen. Get medical attention immediately If the victim has stopped breathing open airway, loosen collar and belt, and administer artificial respiration. Keep the victim warm and Contact: Flush eyes with plenty of water for at least 20 minutes retracting eyelids Safety data SheetProduct identifier used on the label: Slick SandStock Number: 100709 Revision Date: 06-20-2017 Replaces: 01-20-2017 Page 4 of 14often. Tilt the head to prevent chemical from transferring to the uncontaminated eye. Get immediate medical Contact: Wash with soap and water.

5 Remove contaminated clothing and launder. Get medical attention if irritation develops or persists. Wash clothing before reuse. Wash affected area thoroughly with soap and : Do not induce vomiting and seek medical attention immediately. Drink two glasses of water or milk to dilute. Provide medical care provider with this SDS. If vomiting occurs spontaneously, keep head below hips to prevent aspiration of liquid into lungs. If possible, do not leave individual unattended. If individual is drowsy or unconscious, do not give anything by mouth; place individual on left side with head important symptoms/effects, acute and delayed:May be fatal if swallowed and enters airways. Causes skin irritation. May cause an allergic skin reaction. Causes serious eye irritation. Causes damage to organs. Causes damage to organs through prolonged or repeated exposureIndication of immediate medical attention and special treatment needed, if necessary:No additional first aid information available 5.

6 Fire-fighting measuresSuitable (and unsuitable) extinguishing media: Suitable extinguishing media:Use alcohol resistant foam, carbon dioxide, or dry chemical extinguishing agents. Water may be ineffective but water spray can be used extinguish a fire if swept across the base of the flames. Water can absorb heat and keep exposed material from being damaged by fire. Regular foamUnsuitable extinguishing media: No data availableSpecific hazards arising from the chemical: Vapors may be ignited by sparks, flames or other sources of ignition if material is above the flash point giving rise to a fire (Class B). Vapors are heavier than air and may travel to a source of ignition and flash combustion products: Carbon dioxide, Carbon monoxide, Styrene oxide, , HydrocarbonsSpecial protective equipment and precautions for fire-fighters: Do not enter fire area without proper protection including self-contained breathing apparatus and full protective equipment.

7 Fight fire from a safe distance and a protected location due to the potential of hazardous vapors and decomposition products. Wear a self contained breathing apparatus (NIOSH approved) with a full face piece operated in the positive pressure demand mode with appropriate turn-out gear and chemical resistant personal protective equipment. Water may be used to Safety data SheetProduct identifier used on the label: Slick SandStock Number: 100709 Revision Date: 06-20-2017 Replaces: 01-20-2017 Page 5 of 14cool closed containers to prevent pressure build-up and possible auto ignition or explosion when exposed to extreme heat. 6. Accidental release measuresPersonal precautions, protective equipment and emergency procedures: Exposure to the spilled material may be irritating or harmful. Follow personal protective equipment recommendations found in Section 8 of this SDS. Additional precautions may be necessary based on special circumstances created by the spill including; the material spilled, the quantity of the spill, the area in which the spill occurred.

8 Also consider the expertise of employees in the area responding to the and materials for containmentand cleaning up: Prevent the spread of any spill to minimize harm to human health and the environment if safe to do so. Wear complete and proper personal protective equipment following the recommendation of Section 8 at a minimum. Dike with suitable absorbent material like granulated clay. Gather and store in a sealed container pending a waste disposal evaluation. Use an inert absorbent such as sand or vermiculite. Place in properly labeled closed container. Avoid breathing vapors. All personnel in the area should be protected as in Section 8. Activate available exhaustventilation equipment in the immediate spill area. Shut off ignition sources; including electrical equipment and flames. Do not allow smokingin the area. 7. Handling and storage Precautions for safe handling: Harmful or irritating material. Avoid contacting and avoid breathing the material.

9 Use only in a well ventilated area. Keep out of the reach of children. Keep container closed when not in use. Do not take internally. Avoid contact with material, avoid breathing dusts or fumes, use only in awell ventilated area. Use with adequate ventilation Wash hands before eating Do not get in eyes, on skin and clothing All hazard precautions given in the data Sheet must be for safe storage, including any incompatibilities: Safe storage conditions: Store in a cool dry ventilated location. Isolate from incompatible materials and conditions. Keep container(s) closed. Avoid contact with incompatible materials. Store in a tightly closed container Keep away from heat, sparks, and flame For maximum product quality, avoid prolonged storage at temperatures above 75 F (25 C).Materials to Avoid/Chemical Incompatibility: Peroxides, Strong acids, Strong oxidizing agents, Halogens, Strong alkaliesSafety data SheetProduct identifier used on the label: Slick SandStock Number: 100709 Revision Date: 06-20-2017 Replaces: 01-20-2017 Page 6 of 14 8.

10 Exposure controls/personal protectionOSHA permissible exposure limit (PEL), American Conference of Governmental Industrial Hygienists (ACGIH) Threshold Limit Value (TLV), and any other exposure limit used or recommended by the chemical manufacturer, importer, or employer preparing the Safety data Sheet , where available:Chemical componentOSHA PELACGIH TLVACGIH STELIDLHTalc20 mppcf2 mg/m3No data available1000 mg/m3 IDLH (containing no asbestos and <1% quartz)Styrene100 ppm20 ppm40 ppm STEL; 170 mg/m3 STEL700 ppm IDLHA cetone1000 ppm500 ppm750 ppm2500 ppm IDLH (10% LEL)Titanium dioxide15 mg/m310 mg/m3No data available5000 mg/m3 IDLHA ppropriate engineering controls: No exposure limits exist for the constituents of this product. Use local exhaust ventilation or other engineering controls to minimize exposures and maintain operator comfort. Individual protection measures, such as personal protective equipment:Respiratory Protection:Respiratory protection may be required to avoid overexposure when handling this product.