SAFETY DATA SHEET - LPS Labs

1 SAFETY DATA SHEET1. IdentificationLPS Heavy-Duty Silicone ( aerosol )Product identifierOther means of identification01516, C01516 Part NumberAn industrial lubricant designed to reduce mechanical wear and to extend equipment life ofmachinery where rubber and plastics are involved and where silicone can be useNone restrictionsManufacturer/Importer/Suppli er/Distributor informationManufacturerCompany nameITW Pro BrandsAddress4647 Hugh Howell , GA 30084 Country( )Tel: +1 770-243-8800In Case of Permatex Canada1-35 Brownridge RoadHalton Hills, ON, L7G 0C6 Canada1-800-241-8334 Supplier2.

2 Hazard(s) identificationCategory 2 Flammable aerosolsPhysical hazardsLiquefied gasGases under pressureNot hazardsNot hazardsLabel elementsSignal wordWarningHazard statementFlammable aerosol . Contains gas under pressure; may explode if statementPreventionKeep away from heat, hot surfaces, sparks, open flames and other ignition sources. No not spray on an open flame or other ignition source. Do not pierce or burn, even after hands after from sunlight. Store in a well-ventilated place. Do not expose to temperatures exceeding50 C/122 of waste and residues in accordance with local authority hazardsNone informationNone Composition/information on ingredientsMixtures1 / 8 Material name: LPS Heavy-Duty Silicone ( aerosol )01516, C01516 Version #: 02 Revision date: 05-12-2017 Issue date.

3 01-03-2017 SDS CANADACAS number%Chemical nameCommon name and synonyms64742-48-9 Naphtha, Petroleum, HydrotreatedHeavy10 - 2068476-86-8 Petroleum gases, Liquefied,Sweetened10 - 2063148-62-9 Poly (Dimethylsiloxane)1 - 315733-22-94-chloro-3-methylphenol - 1532-32-1 Sodium - 11338-43-8 Sorbitan - 1 All concentrations are in percent by weight unless ingredient is a gas. Gas concentrations are in percent by First-aid measuresMove to fresh air. Call a physician if symptoms develop or contaminated clothing. Wash with plenty of soap and water.

4 If skin irritation occurs: Getmedical advice/attention. Wash contaminated clothing before contactRinse with water. Get medical attention if irritation develops and contactNot likely, due to the form of the product. In the unlikely event of swallowing contact a physician orpoison control center. Rinse irritation. May cause redness and importantsymptoms/effects, acute anddelayedProvide general supportive measures and treat symptomatically. Keep victim under may be of immediatemedical attention and specialtreatment neededEnsure that medical personnel are aware of the material(s) involved, and take precautions toprotect information5.

5 Fire-fighting measuresWater spray. Water fog. Alcohol resistant foam. Dry chemical powder. Carbon dioxide (CO2).Suitable extinguishing mediaDo not use water jet as an extinguisher, as this will spread the extinguishingmediaContents under pressure. Pressurized container may explode when exposed to heat or fire, gases hazardous to health may be hazards arising fromthe chemicalFirefighters must use standard protective equipment including flame retardant coat, helmet withface shield, gloves, rubber boots, and in enclosed spaces, protective equipmentand precautions for firefightersIn case of fire: Stop leak if safe to do so.

6 Do not move cargo or vehicle if cargo has been exposedto heat. If tank, rail car or tank truck is involved in a fire, ISOLATE for 800 meters (1/2 mile) in alldirections; also consider initial evacuation for 800 meters (1/2 mile) in all directions. ALWAYS stayaway from tanks engulfed in flame. Move containers from fire area if you can do so without should be cooled with water to prevent vapor pressure build up. For massive fire incargo area, use unmanned hose holder or monitor nozzles, if possible. If not, withdraw and let fireburn fightingequipment/instructionsUse standard firefighting procedures and consider the hazards of other involved materials.

7 Movecontainers from fire area if you can do so without risk. Cool containers exposed to flames withwater until well after the fire is out. In the event of fire and/or explosion do not breathe methodsFlammable aerosol . Contents under pressure. Pressurized container may explode when exposedto heat or fire hazards6. Accidental release measuresKeep unnecessary personnel away. Keep people away from and upwind of spill/leak. Keep out oflow areas. Many gases are heavier than air and will spread along ground and collect in low orconfined areas (sewers, basements, tanks).

8 Wear appropriate protective equipment and clothingduring clean-up. Emergency personnel need self-contained breathing equipment. Do not touchdamaged containers or spilled material unless wearing appropriate protective clothing. Ventilateclosed spaces before entering them. Local authorities should be advised if significant spillagescannot be contained. For personal protection, see section 8 of the precautions,protective equipment andemergency procedures2 / 8 Material name: LPS Heavy-Duty Silicone ( aerosol )01516, C01516 Version #: 02 Revision date: 05-12-2017 Issue date: 01-03-2017 SDS CANADAR efer to attached SAFETY data sheets and/or instructions for use.

9 Stop leak if you can do so withoutrisk. Use water spray to reduce vapors or divert vapor cloud drift. Isolate area until gas hasdispersed. Eliminate all ignition sources (no smoking, flares, sparks, or flames in immediate area).Keep combustibles (wood, paper, oil, etc.) away from spilled Spills: Dike the spilled material, where this is possible. Absorb in vermiculite, dry sand orearth and place into containers. Scoop up used absorbent into drums or other appropriatecontainer. Following product recovery, flush area with Spills: Wipe up with absorbent material ( cloth, fleece).

10 Clean surface thoroughly toremove residual return spills to original containers for re-use. For waste disposal, see section 13 of the and materials forcontainment and cleaning upAvoid discharge into drains, water courses or onto the precautions7. Handling and storagePressurized container: Do not pierce or burn, even after use. Do not use if spray button is missingor defective. Do not spray on a naked flame or any other incandescent material. Do not smokewhile using or until sprayed surface is thoroughly dry. Do not cut, weld, solder, drill, grind, orexpose containers to heat, flame, sparks, or other sources of ignition.