SAFETY DATA SHEET - pbfenergy.com

1 SAFETY data SHEET1. IdentificationProduct identifierVP Lubricant Base OilOther means of identificationSDS numberPB361337-00 SynonymsStraight Cut Oil - VP 100 Recommended useBase material for the production of various lubricating oilsA complex combination of hydrocarbons obtained as the raffinate from a solvent extractionprocess. It consists predominantly of saturated hydrocarbons having carbon numberspredominantly in the range of C20 through C50 and produces a finish oil with a viscosity of at least100 SUS at 100 F (19cSt at 40 C).Recommended restrictionsNone informationPaulsboro Refining Company800 Billingsport RoadPaulsboro, NJ number856-224-6605 Emergency telephonenumberChemtrec 800-424-93002. Hazard(s) identificationNot hazardsCategory 1 Aspiration hazardHealth hazardsNot defined hazardsLabel elementsSignal wordDangerHazard statementMay be fatal if swallowed and enters statementPreventionObserve good industrial hygiene swallowed: Immediately call a poison center/doctor.

2 Do NOT induce locked of contents/container in accordance with local/regional/national/international (s) not otherwiseclassified (HNOC)None Composition/information on ingredientsSubstances64742-70-7100 Paraffin oils (petroleum),catalytic dewaxed heavyCAS numberCommon name andsynonyms%Chemical nameComposition commentsIP346 method DMSO extract for base oil substances: < Lubricant Base OilSDS US924943 Version #: 01 Revision date: - Issue date: 06-February-20151 / 74. First-aid measuresInhalationMove to fresh air. If breathing is difficult, give oxygen. Get medical attention, if contactRemove contaminated clothing and shoes. Wash off immediately with soap and plenty of medical attention if irritation develops or persists. Wash clothing separately before or thoroughly clean contaminated shoes.

3 If high pressure injection under the skin occurs,always seek medical contactImmediately flush eyes with plenty of water for at least 15 minutes. Remove contact lenses, ifpresent and easy to do. Continue rinsing. Get medical mouth thoroughly. Do not induce vomiting without advice from poison control center. Ifvomiting occurs, keep head low so that stomach content does not get into the lungs. Get medicalattention importantsymptoms/effects, acute anddelayedProlonged or repeated skin contact may cause drying, cracking, or of immediatemedical attention and specialtreatment neededProvide general supportive measures and treat symptomatically. Symptoms may be informationGet medical attention if symptoms occur. Show this SAFETY data SHEET to the doctor in Fire-fighting measuresSuitable extinguishing mediaWater spray.

4 Water fog. Dry chemical powder. Carbon dioxide (CO2).Unsuitable extinguishingmediaDo not use water hazards arising fromthe chemicalThe product is not flammable. Will burn if involved in a protective equipmentand precautions for firefightersWear full protective clothing, including helmet, self-contained positive pressure or pressuredemand breathing apparatus, protective clothing and face fightingequipment/instructionsWithdraw immediately in case of rising sound from venting SAFETY devices or any discoloration oftanks due to fire. Fight fire from maximum distance or use unmanned hose holders or monitornozzles. Move containers from fire area if you can do it without risk. In the event of fire, cool tankswith water spray. Cool containers exposed to flames with water until well after the fire is out. Formassive fire, use unmanned hose holders or monitor nozzles; if this is impossible, withdraw fromarea and let fire burn.

5 Water runoff can cause environmental damage. Use compatible foam tominimize vapor generation as fire hazardsThis product is not flammable. Will burn if involved in a Accidental release measuresPersonal precautions,protective equipment andemergency proceduresKeep unnecessary personnel away. Do not touch damaged containers or spilled material unlesswearing appropriate protective clothing. In case of spills, beware of slippery floors and Section 8 of the SDS for Personal Protective and materials forcontainment and cleaning upSmall Spills: Absorb with earth, sand or other non-combustible material and transfer to containersfor later disposal. Clean surface thoroughly to remove residual Spills: Prevent entry into waterways, sewers, basements or confined areas. If necessarydike the product with dry earth, sand or similar non-combustible materials.

6 Absorb with inertabsorbent such as dry clay, sand or diatomaceous earth, commercial sorbents, or recover usingpumps. Clean surface thoroughly to remove residual precautionsContain spillages with sand, earth or any suitable adsorbent material. Prevent spillage entering awatercourse or sewer, contaminating soil or vegetation. If this is not possible notify police andappropriate authorities Handling and storagePrecautions for safe handlingKeep away from heat, spark, open flames and other sources of ignition. Avoid prolonged orrepeated contact with skin. Be aware of potential for surfaces to become for safe storage,including any incompatibilitiesStore in a dry place. Keep away from incompatible materials, open flames and high Lubricant Base OilSDS US924943 Version #: 01 Revision date: - Issue date: 06-February-20152 / 78.

7 Exposure controls/personal protectionOccupational exposure limitsUS. OSHA Table Z-1 Limits for Air Contaminants (29 CFR )ValueTypeFormComponentsPEL5 Mist, mineral (CAS -)US. ACGIH Threshold Limit ValuesValueTypeFormComponentsTWA5 mg/m3 Inhalable Mist, mineral (CAS -)US. NIOSH: Pocket Guide to Chemical HazardsValueTypeFormComponentsSTEL10 Mist, mineral (CAS -)TWA5 limit valuesNo biological exposure limits noted for the ingredient(s).Appropriate engineeringcontrolsProvide adequate general and local exhaust ventilation. Use process enclosures, local exhaustventilation, or other engineering controls to control airborne levels below recommended protection measures, such as personal protective equipmentEye/face protectionWear SAFETY glasses. If splash potential exists, wear full face shield or chemical protectionHand protectionChemical/oil resistant gloves are recommended.

8 Be aware that the liquid may penetrate thegloves. Frequent change is work clothing (long sleeved shirts and long pants) is protectionIf engineering controls do not maintain airborne concentrations below recommended exposurelimits (where applicable) or to an acceptable level (in countries where exposure limits have notbeen established), an approved respirator must be hazardsWear appropriate thermal protective clothing, when hygieneconsiderationsAlways observe good personal hygiene measures, such as washing after handling the materialand before eating, drinking, and/or smoking. Routinely wash work clothing to removecontaminants. Discard contaminated footwear that cannot be Physical and chemical propertiesAppearance Physical Clear thresholdNot point/freezing pointNot boiling point and boilingrange> F (> 316 C)Flash point> F (> C) ASTM D-92 Evaporation rateNot (solid, gas)Not flammability or explosive limitsFlammability limit - lower(%)> limit - upper(%)< 7 Explosive limit - lower (%)Not limit - upper (%)Not pressure< mm Hg (20 C)VP Lubricant Base OilSDS US924943 Version #: 01 Revision date: - Issue date: 06-February-20153 / 7 Vapor density> 2 Relative densityNot (ies)Solubility (water)InsolublePartition coefficient(n-octanol/water)No data temperatureNot temperatureNot mm /s (40 C)Other informationExplosive propertiesNot formulaUVCBO xidizing propertiesNot F (-4 C)10.

9 Stability and reactivityReactivityThe product is stable and non-reactive under normal conditions of use, storage and stabilityStable under normal temperature conditions and recommended of hazardousreactionsHazardous polymerization does not to avoidContact with incompatible materials. Do not pressurize, cut, weld, braze, solder, drill, grind orexpose empty containers to heat, flame, sparks, static electricity, or other sources of ignition; theymay explode and cause injury or materialsStrong oxidizing decompositionproductsCarbon oxides. Sulfur oxides. Toxicological informationInformation on likely routes of exposureInhalationInhalation of oil mist or vapors formed during heating of the product will irritate the respiratorysystem and provoke contactFrequent or prolonged contact may defat and dry the skin, leading to discomfort and contactDirect contact with eyes may cause temporary or vomiting of the liquid may result in aspiration into the lungs.

10 Ingestion of largeamounts may produce gastrointestinal disturbances including irritation, nausea, and related to thephysical, chemical andtoxicological characteristicsSymptoms may include redness, drying and cracking of the skin. Droplets of the product aspiratedinto the lungs through ingestion or vomiting may cause a serious chemical on toxicological effectsAcute toxicityHuman evidence indicates that the product has very low acute oral, dermal or inhalation , it can produce severe injury if taken into the lung as a liquid, and there may be profoundcentral nervous system depression following prolonged exposure to high levels of corrosion/irritationProlonged skin contact may cause temporary eye damage/eyeirritationDirect contact with eyes may cause temporary or skin sensitizationRespiratory sensitizationNot sensitizationNot cell mutagenicityNot Monographs.