Salt Eliminator Material Safety Data Sheet

1 Salt Eliminator Page 1 of 4 Material Safety Data Sheet 1. Chemical Product and Company Information Product Name: KROWN MR35 SALT Eliminator Product Item Numbers: KR-001198 15 oz / 426 g Product Manufacturer: Empack Spraytech Inc. Address: 98 Walker Drive Brampton, Ontario, Canada L6T 4H6 Telephone: (905) 792 6571 Emergency Telephone: Empack: (905) 792-6571 (8:00 am 4:00 pm ET) CANUTEC: (613) 996-6666 collect (24 Hours) Product Use: Salt Eliminator WHMIS Classification: A, D-2B TDG Classification: AEROSOLS, Class , UN1950 Under the Clear Language Regulations: refer to Section for Limited Quantity Shipping Information, if shipping under this exemption.

2 Prepared By: Empack Regulatory Department Preparation Date: January 15, 2015 2. Composition / Information on Ingredients Hazardous Ingredients CAS Number Weight % TLV- ACGIH (ppm) Ethylene glycol monobutyl ether 111-76-2 1- 5 Not listed 3. Hazards Identification Emergency overview: This is an acidic spray mist. Do not spray on eyes. May irritate eyes and skin. May cause drying of skin. Potential Health Effects: Inhalation: No inhalation affects are expected when used as directed. Skin Contact: Can cause skin irritation. Prolonged or repeated contact may dry the skin. Eye Contact: This product causes irritation, redness and pain. Ingestion: Ingestion may cause vomiting and weakness. Carcinogenicity of Material : None known. 4. First Aid Measures Inhalation: Move victim to fresh air. If irritation persists, give artificial respiration and get medical attention IMMEDEATLY.

3 Skin Contact: Wash thoroughly with soap and water. Eye Contact: Immediately flush eyes with plenty of water. Get medical attention if irritation persists. Ingestion: Do not induce vomiting, get medical attention. Note to Physicians: Treat symptomatically. Salt Eliminator Page 2 of 4 5. Fire Fighting Measures Flammability Class: Not Flammable If Yes, Under Which Conditions: N/Ap Flash Point (propellant): N/Ap (Propellant is compressed air) Autoignition Temperature (propellant): N/Ap Flammability Limits in Air (%): LEL: N/Ap, UEL: N/Ap Fire and Explosion Hazards: May decompose on contact with flames or extremely hot metal surfaces to produce toxic and corrosive products. Thermal decomposition products are toxic and may include oxides of carbon. Extinguishing Media: Water Fog, Dry Chemical, CO2 and Foam Sensitivity to Mechanical Impact: Not expected to be sensitive.

4 Sensitivity to Static Discharge: Not expected to be sensitive 6. Accidental Release Measure Spill and Leak: Large spill or leak is unlikely in aerosol containers. If happens, Soak up with absorbent Material and hold for disposal. 7. Handling And Storage Do not breathe vapour or mist. Avoid contact with eyes, skin and clothing. Keep container closed. Use only with adequate ventilation. Avoid freezing. Store in a cool dry 8. Exposure Controls/Personal Protection Engineering Controls: Local exhaust ventilation required to maintain the point of use below the Threshold Limit Value if unprotected personnel are involved. Respiratory Protection: Use dust and mist respirator if needed. Eye Protection: Use dust and chemical resistance Safety goggles or full-face shield when there is a potential for eye contact. Skin Protection: Not normally required. Use impermeable gloves, OR rubber/ latex gloves when there is a potential for prolonged skin contact.

5 9. Physical And Chemical Properties Physical State: Aerosol Appearance: Orange/ red mist Odour: Fruity/citrus odor Odour Threshold: Not Available Boiling Point: 100 C Vapour Density (Air = 1): Not available Specific Gravity: @ 25 C Vapour Pressure (psia): 40- 50 @ C Evaporation Rate: <1 (n-Butyl Acetate = 1) pH: 4-5 Melting point: Not available Solubility in Water: Soluble Salt Eliminator Page 3 of 4 10. Stability And Reactivity Chemical Stability: Stable at normal temperature & pressures. Incompatible Materials: Strong acids and oxidizing agents. Hazardous Products of Decomposition: May form carbon dioxide and carbon monoxide, and hazardous fumes. Hazardous Polymerization: Will not occur. 11. Toxicological Information Route of Entry: Skin Contact: Yes Skin Absorption: Yes Eye Contact: Yes Inhalation: Yes Ingestion: Yes Effects of Acute Exposure: May cause dermatitis, irritation to eyes, dizziness, and vomiting.

6 Effects of chronic exposure: Avoid prolonged skin contact, use in well ventilated conditions. Carcinogenicity of Material : None known when used below acute toxicity limit. Reproductive effects: No information is available. Teratogenicity: No information is available. Mutagenicity: No information is available. Acute toxicity Ethylene glycol monobutyl ether: LD50 Rat Oral: 3,860 mg/kg. LC50 Rat Inhalation: Not available. 12. Ecological Information When spill, pick up with mop or wet-vac. Then dispose waste according to local provincial and federal regulations. 13. Disposal Considerations Dispose of in accordance with local, provincial and federal regulations. 14. Transport Information Ground: Consumer Commodity, ORM-D. Air: Cannot be shipped by air. Sea: AEROSOLS, UN# 1950, Class Salt Eliminator Page 4 of 4 15. Regulatory Information CANADA WHMIS Classification: A: Compressed gas, D2B: Material causing other toxic Materials.

7 USA Environmental Protection Act: Constituents of this product are included on the TSCA inventory. OSHA (29 CFR ) Classification: Compressed Gas. HMIS: 1 Health, 1 Fire, 1 Reactivity. 16. Other Information Abbreviations: ACGIH American Conference of Governmental Industrial Hygienists CAS Chemical Abstract Service NIOSH National Institute for Occupational Safety and Health OSHA Occupational Safety and Health Administration, USA TSCA Toxic Substances Control Act 1976, USA PEL Permissible Exposure Limit TLV Threshold Limit Value WHIMIS Workplace Hazardous Materials Information System Disclaimer: This product has been classified in accordance with the hazard criteria of the CPR and the MSDS contains all the information required by the CPR. This MSDS is valid for three years. The information contained herein is based on data considered accurate. No warranty is expressed or implied regarding the accuracy of this data or the results obtained from the use thereof.

8 Empack assumes no responsibility for personal injury or property damage to vendees or users or third parties, caused by the Material . Such vendees or users assume all risks with the use of the Material .