SCREWS - Gregg Distributors

1 SCREWS / Bolts / FastenersBody Bolts / Nuts / Fasteners / RetainersRivets & AccessoriesMisc. Hardware / Thread Repair / Steel StockAutomotive / Industrial AssortmentsYour 100% Canadian Single Source!H24 LAG screw EXPANSION SHIELDDie-cast zinc alloy expansion shield for anchoring lag SCREWS in a variety of base materials, including concrete, concrete block, brick, and mortar joints. Radial ribs provide additional holding power in softer material. Material: Die-cast Zamac 3 alloySURE WALL DRYWALL ANCHORSSelf-drilling anchors for use in softer substrates like drywall. The point cuts a hole through the base material, eliminating break-out on the backside of softer base materials. The standard Sure Wall can be used as a fastener in fixtures with sufficiently large holes or a screw can be driven into the anchor body for smaller fixture holes of picture-hanging wire.

2 Features: Self drilling - only a screwdriver needed for installation in gypsum board drywall, can be used alone or with SCREWS , and maximizes the load carrying capacity of low-strength base materials Material: Die cast zinc or reinforced nylon Includes anchor and screwSTRONG-BOLT 2 WEDGE ANCHOR FOR CRACKED AND UNCRACKED CONCRETE Category 1 anchor classification: The Strong-Bolt 2 anchor received classification as a Category 1 anchor, which is established by performance in reliability tests in accordance with AC193 and test criteria. Category 1 is the highest attainable anchor category for reliability. Tri-segmented clip: Each segment adjust independently, increasing follow-up expansion should the hole increase in size as a result of a crack. Dual embossments on each clip segment: Enables clip to undercut into the concrete thereby increasing follow-up expansion should a crack occur.

3 High-strength alloy clip on carbon-steel anchors: This special alloy clip offers improved performance. Standard (ANSI) fractional anchor: Fits most fixtures and installs with common drill bit sizes and STRONG-TIE Anchoring & Fastening SystemsSIM/3517 DROP-IN INTERNALLY-THREADED EXPANSION SHELL ANCHORI nternally threaded, deformation-controlled expansion anchors with a pre-assembled expander plug, suitable for flush mount applications in solid base materials. The anchor is set by driving the expansion plug towards the bottom of the anchor using the setting tool. Material: Carbon steel Finish: Carbon steel: Zinc platedDROP-IN INTERNALLY-THREADED EXPANSION SHELL ANCHORN ewer, updated design offers easier installation than previous versions as it sets with 40% fewer hammer strikes. Positive-set marking system indicates when anchor is properly set.

4 Internally threaded, deformation-controlled expansion anchors with a pre-assembled expander plug, suitable for flush mount applications in solid base materials. The anchor is set by driving the expansion plug towards the bottom of the anchor using the setting tool. Material: Carbon steel Finish: Carbon steel: Zinc platedPart No. MaterialApplicationsScrew SizeSWZ08 LZinc3/8 , 1/2 , 5/8 drywall, plaster#8 x 1-1/4 SWN08 LNylon3/8 , 1/2 drywall, ceiling tileSWZ06 Zinc3/8 , 1/2 drywall, ceiling tile, plaster, pegboard#6 x 7/8 SWN06 Nylon3/8 , 1/2 drywall, ceiling tilePart SizeDrill Bit DiameterBolt Threads (per in.)Body LengthDIA625/8 7/8 112-1/2 Part SizeDrill Bit DiameterBolt Threads (per in.)Body LengthDIAB251/4 3/8 201 DIAB373/8 1/2 161-9/16 DIAB501/2 5/8 132 DIAB625/8 7/8 112-1/2 DIAB753/4 1 103-1/8 Part (in.)Bolt SizeDrill Bit DiameterThread LengthSTB2-251341/4 x 1-3/41/415/16 STB2-252141/4 x 2-1/41/41-7/16 STB2-253141/4 x 3-1/41/42-7/16 Part (in.)

5 Allowable Tension Load(f c 3000 psi)Bolt SizeDrill Bit DiameterEmbed. DepthLSES25S1/4 Short1/2190 LSES31S5/16 Short1/21-1/4100 LSES37S3/8 Short5/81-3/4220 LSES50S1/2 Short3/42250 LSES25L1/4 Long1/21-1/2120 LSES31L5/16 Long1/21-3/4150 LSES37L3/8 Long5/82-1/2260 LSES50L1/2 Long3/43310 DROP-IN ANCHOR SETTING TOOLPart Use WithDIAST25 DIA25 DIAST50 DIA50 DIAST62 DIA62 DIAST75 DIA75 Part Use WithDIABST25 DIAB25 DIABST37 DIAB37 DIABST50 DIAB50 DIABST62 DIAB62 DIABST75 DIAB75 TITEN CONCRETE & MASONRY SCREWSFor attaching all types of components to concrete and masonry. Use these products in dry, interior, and non-corrosive environments only. Material: High-treated carbon steel Finish: Zinc-plated with a baked on ceramic coating 3/16 Diameter Standard Blue Titen 5/32 Drill Bit Diameter 1/4 Diameter Standard Blue Titen 3/16 Drill Bit Diameter 1/4 Diameter Standard Blue Titen 2 3/16 Drill Bit DiameterSize(in.)

6 Hex Head Part Flat Head Part x 1-1/4 TTN25114H TTN25114PF1/4 x 1-3/4 TTN25134PF1/4 x 2-1/4 TTN25214H TTN25214PF1/4 x 2-3/4 TTN25234H TTN25234PF1/4 x 3-1/4 TTN25314H TTN25314PF1/4 x 3-3/4 TTN25334H TTN25334PF1/4 x 4 TTN25400H TTN25400PF1/4 x 5 TTN25500H TTN25500PF1/4 x 6 TTN25600H TTN25600 PFSize(in.)5/16 Hex Head Part No.#3 Phillips Flat Head Part x 1-3/4 TTN2-25134H TTN2-25134 PFSize(in.)Hex Head Part Flat Head Part x 1-1/4 TTN18114H TTN18114PF3/16 x 1-3/4 TTN18134H TTN18134PF3/16 x 2-1/4 TTN18214H TTN18214PF3/16 x 2-3/4 TTN18234H TTN18234PF3/16 x 3-1/4 TTN18314H TTN18314PF3/16 x 3-3/4 TTN18334H TTN18334PF3/16 x 4 TTN18400H TTN18400 PFDROP-IN ANCHOR SETTING TOOLHand-setting tool designed for use with the new Simpson Strong-Tie Drop-In anchor (DIAB), ensuring fast, easy and economical Sequenc