SECTION J SPLIT FLASHINGS - Thaler Metal

1 SPLIT FLASHINGSSECTION JA-0 ROOF SPECIALTIESSPLIT FLASHINGSCANADA: : WEB: EMAIL: be advised Thaler products may undergo improvements from time to time and are subject to change without Or EqualSPJ-1 Round SPLIT Flashing SPJ-2 Round SPLIT Flashing (Vented Cap)SPJ-3 Square SPLIT Flashing SPJ-4 Square SPLIT flashing (Vented Cap) SPLIT Flashing SpecificationJ-0J-1, J-1AJ-2, J-2AJ-3J-4, J-4AJ-5 to J-7 TABLE OF CONTENTSCANADA: : WEB: EMAIL: be advised Thaler products may undergo improvements from time to time and are subject to change without OR EQUALWHAT IT TAKES TO BEWhen specifications read Thaler or Equal, it is the responsibility of specifiers and building owners to determine what it means to be Or Equal.

2 The following data has been presented to quickly help assess the comparative merits of competitive products. Thaler SPLIT FLASHINGS products have a number of Value Added features that should be considered when trying to equate the Or Equal .100% Watertight; unlike soldered-type SPLIT FLASHINGS or pitch pans, Thaler SPLIT FLASHINGS provide an unparal-leled seal and remain flexible enough to allow movement of penetrating items while coping with the vibration often associated with cooling tower supports and similar mechanical flashing; Thaler SPLIT FLASHINGS are designed to do away with the ultimately expensive, unreliable and high maintenance "pitch pans".

3 They pose an open threat of leaks and require frequent maintenance checks and repair of bitumen embrittled by sunlight and cold for structural protrusions; many techniques employed to flash complicated shapes such as H-beams, I-beams and C-channels can be labour intensive and lacking in consistent quality, performance and looks. Thaler SPLIT FLASHINGS are quality controlled at the factory, sized to accommodate precise web thicknesses, while sleeves employ a simple, applicator-friendly, snap together "lock-fast" installation proven concept; Thaler SPLIT FLASHINGS provide the best flashing detail at roof penetrations which follows the general rule of attaching the base flashing (sleeve) to the structural deck and counter flashing (cap) to the penetrating pleasing; arguably the best looking SPLIT flashing available on the market today.

4 Unique installation method means clean assembly without messy caulking seals, soldered joints or ; providing SPLIT FLASHINGS are carefully twisted off, they can be used again for re-roofing Triple Pressure Grommet Seal; EPDM "memory" in the seal provides constant pressure to outside of protrusion to prevent leaks. See Thaler EPDM Flashing Seals Approved; all Thaler FLASHINGS conform to CSA B272-93 - Prefabricated Self-Sealing Roof Vent deck flange; can be PVC coated for proper welding of PVC membrane or bituminous painted for BUR or ModBit year Warranty; guaranteed against leaks and defects in materials and/or manufacture when installed in accordance with Thaler "Installation Instructions".

5 Maintenance-Free; never needs caulking (any caulking at any time will invalidate 20 year warranty. Written "Installation Instructions"; provided with every Thaler THECOMPETITIONTHALER VALUEADDED FEATURESROOF SPECIALTIESSPLIT FLASHINGSSTEEL DECKCONCRETE DECKEPDM TRIPLE PRESSURE GROMMET SEAL1/8" (3 mm) STAINLESS STEEL NUTS AND BOLTS26 ga. TYPE 304 STAINLESS STEEL CAP26 ga. TYPE 304 STAINLESSSTEEL SLEEVE5" (127 mm)FROM 9" TO 48" HIGH (229 mm TO 1220 mm) IN ANY INCREMENTONE THIRD OF SLEEVE SIZE TO MAXIMUM OF 12" (305 mm)3 PLY FELT FLASHING OVER FLANGE 4" (102 mm), 6" (152 mm) AND 8" (203 mm) ONTO ROOF4" (102 mm) TO 120" (3048 mm) DIA.)

6 IN ANY INCREMENTIS STANDARDTOP VIEW OF CAPSTAINLESS STEEL CLIPS,ARE USED TO SNAP OR LOCK FRICTION FITTED FLASHING SECTION TOGETHER EMBED DECK FLANGE IN LAYER OF PLASTIC CEMENT (B UR)1" (25 mm)ROOF SPECIALTIESSPJ-1 ROUNDSPLIT FLASHINGS DESCRIPTION: Thaler SPJ-1 Round SPLIT FLASHINGS consist of a SPLIT stainless steel flashing sleeve with integral deck flange and SPLIT coolie-hat cap fitted with an EPDM triple pressure grommet seal. Continuous EPDM seals are also located at the SPLIT junctures of the sleeve and deck flange.

7 Available in stainless steel only. Clips are used to snap or lock the friction-fit flashing sections :3" to 120" (76 mm to 3048 mm) in any increment. Note: FLASHINGS are installed in two SPLIT sections for up to 48" (1220 mm) dia; three sections for 48" to 72" (1220 mm to 1830 mm) dia; four sections for over 72" (1830 mm) dia. HEIGHT:9" to 48" (229 mm to 1220 mm) in any FEATURES:Custom sizing is standard. Never needs caulking (see Thaler EPDM Flashing Seals literature). More economical than SPJ-2 Round SPLIT Flashing (Vented Cap).

8 OPTIONS:PVC coated deck flange for PVC roof membrane. Bituminous painted deck flange for BUR and ModBit roof membrane. See SPJ- 2 for vented cap (prevents condensation build-up on inside of sleeve).RECOMMENDED USE:Suitable for round plastic, steel, stainless, copper or cast iron pipes, stacks or other round roof projections where flashing sleeve can only be fitted around the projection rather than over it. Example uses include hydro generator stacks, oil refinery process piping, railings, and other retrofit :CSA Approved to CSA B272-93 (Prefabricated Self-Sealing Roof Vent FLASHINGS ).

9 Note: In addition to the CSA tests, Thaler in-house testing was performed with the EPDM Triple Pressure Grommet Seal submerged in 8" (203 mm) of water for 3 months with no :20 year warranty against leaks and defects in materials and/or manufacture when installed in accordance with Thaler "Installation Instructions". Warranty not valid where EPDM seals are subjected to unusually harsh corrosive environments pulp mills, mining facilities and similar applications. MAINTENANCE:No maintenance required (maintenance free).

10 SPECIFICATION (SHORT FORM):Round SPLIT FLASHINGS : Thaler SPJ-1 Round, SPLIT Flashing [12" (305 mm) high] x [8" (203 mm) dia.] [of sizes as noted on drawings] .018" (26 ga.) sleeve with gauge of cap to suit, Type 304 stainless steel; to CSA B272-93; with EPDM triple pressure grommet seal around cap and continuous EPDM seals at SPLIT junctures of sleeve and deck flange; [PVC coated deck flange] [bituminous painted deck flange]; matching SPLIT cap with overlapped and bolted closure design; manufactured by Thaler Metal Industries, 1-800-387-7217 (Mississauga, Ontario, Canada) or 1-800-576-1200 (New Braunfels, TX), installed as per manufacturer's written instructions.