SEWER PIPE • IPS PRESSURE PIPE - Northern Pipe

1 C900 PRESSURE pipe SEWER pipe IPS PRESSURE pipe WELL CASING DRAIN WASTE VENT. Table of Contents u C900 u WELL CASING. ANSI/AWWA C900 Water Distribution pipe ASTM F480 Well Casing pipe pipe pipe Gasketed Joint Solvent Weld pipe Joint ANSI/AWWA C900 Water Transmission pipe u DRAIN WASTE VENT. pipe ASTM D2665 Schedule 40 Drain Waste Vent Gasketed Joint pipe Truckload Data u BELL END SEWER pipe . Truckload PVC Gravity SEWER pipe Bell End SEWER pipe u GASKETED SEWER pipe Perforation PVC Gravity SEWER pipe Gasketed pipe Gasketed Joint Truckload u IPS PRESSURE pipe . ASTM D2241 PRESSURE pipe Gasketed pipe Gasketed Joint Solvent Weld pipe Schedule 40 PRESSURE pipe Solvent Weld pipe IPS PRESSURE pipe Solvent Weld pipe Joint Truckload Northern pipe products C900. u ANSI/AWWA C900 WATER DISTRIBUTION pipe | pipe Specifications (4" - 12"). Northern pipe Products PVC ANSI/AWWA C900 PVC PRESSURE pipe is manufactured from compounds conforming to cell classification of 12454 as defined in ASTM D1784.

2 The pipe meets the requirements of the ANSI/AWWA C900 standard specification for polyvinyl chloride water distribution pipe . The integral bell joint system meets the requirements of ASTM D3139 and utilizes an elastomeric seal meeting the specification defined in ASTM F477. Northern pipe Products ANSI/AWWA C900 PRESSURE pipe for potable water carries: NSF Standard 14 and NSF Standard 61 listings (marked "NSF-PW-G"). Certification under NSF/ANSI 327 Annex G "lead-free" (marked "NSF-PW-G"). Underwriters Laboratories Inc. Standard 1285 mark of acceptance Canadian Standards Association Standard mark of acceptance ANSI/AWWA C900 (4" - 12") DR-18 and DR-14 distribution pipe carries the Factory Mutual Research Water Distribution pipe for Underground Fire Protection Service mark of acceptance. The pipe is furnished in 20' laying lengths.

3 U ANSI/AWWA C900 | Cell Classification 12454. DR-25 (165 PSI) DR-18 (235 PSI) DR-14 (305 PSI). NOMINAL pipe OUTSIDE. pipe SIZE DIAMETER. (IN.) (IN.) MINIMUM POUNDS MINIMUM POUNDS MINIMUM POUNDS. WALL (IN.) PER FOOT WALL (IN.) PER FOOT WALL (IN.) PER FOOT. 4" " .192" lbs..267" lbs..343" lbs. 6" " .276" lbs..383" lbs..493" lbs. 8" " .362" lbs..503" lbs..646" lbs. 10" " .444" lbs..617" lbs..793" lbs. 12" " .528" lbs..733" lbs..943" lbs. 4 May-2015 | 1302 39th St NW, Fargo, ND 58102 | 701-282-7655 | 800-747-7655 | Fax: 701-282-2887. C900. u ANSI/AWWA C900 WATER DISTRIBUTION pipe | Gasketed Joint Specifications (4" - 12"). Northern pipe Products PVC gasketed ANSI/AWWA C900 PVC potable water distribution pipe is manufactured with gasketed joints conforming to the specifications of ASTM D3139. The gaskets are manufactured to conform to the requirements of ASTM F477.

4 Northern pipe Products employs the Rieber Gasket System. The Rieber joining system is a factory made locked-in flexible elastomeric seal. The gasket is installed in the bell race during the manufacture of the joint. It should not be removed for any reason, as destruction of the joint will occur. u LOCKED-IN GASKET JOINT. B C. D A. Gasket Groove (Race) Outside Diameter E B. Lip Length A. C. Gasket Groove (Race) Length D. Overall Joint E. Spigot Insertion Depth DIMENSIONS (IN.). NOMINAL. pipe SIZE (A). (C) (E). (IN.) GASKET GROOVE (B) (D). GASKET GROOVE SPIGOT INSERTION. (RACE) OUTSIDE LIP LENGTH OVERALL JOINT. (RACE) LENGTH DEPTH. DIAMETER. 4" " " " " ". 6" " " " " ". 8" " " " " ". 10" " " " " ". 12" " " " " ". 5. C900. u ANSI/AWWA C900 WATER TRANSMISSION pipe | pipe Specifications (14" - 24") (Previously C905). Northern pipe Products PVC ANSI/AWWA C900 PVC Water Transmission pipe is manufactured from compounds conforming to cell classification of 12454 as defined in ASTM D1784.

5 The pipe meets the requirements of the ANSI/AWWA C900 standard specification for polyvinyl chloride water transmission pipe . The integral bell joint system meets the requirements of ASTM D3139 and utilizes an elastomeric seal meeting the specification defined in ASTM F477. Northern pipe Products ANSI/AWWA C900 PRESSURE pipe for potable water carries: NSF Standard 14 and NSF Standard 61 listings (marked "NSF-PW-G"). Certification under NSF/ANSI 327 Annex G "lead-free" (marked "NSF-PW-G"). Underwriters Laboratories Inc. Standard 1285 mark of acceptance Canadian Standards Association Standard mark of acceptance 14 and 16 diameter DR-25 and DR-18 transmission pipe carries the Factory Mutual Research Water Distribution pipe for Underground Fire Protection Service mark of acceptance. The pipe is furnished in 20' laying lengths. u ANSI/AWWA C900 | Cell Classification 12454.

6 pipe DR-25 (165 PSI) DR-21 (200 PSI) DR-18 (235 PSI) DR-14 (305 PSI). NOMINAL. OUTSIDE. pipe SIZE. DIAMETER MINIMUM POUNDS MINIMUM POUNDS MINIMUM POUNDS MINIMUM POUNDS. (IN.). (IN.) WALL (IN.) PER FOOT WALL (IN.) PER FOOT WALL (IN.) PER FOOT WALL (IN.) PER FOOT. 14" " .612" lbs..729" lbs..850" lbs. " lbs. 16" " .696" lbs..829" lbs..967" lbs. " lbs. 18" " .780" lbs..929" lbs. " lbs. " lbs. 20" " .864" lbs. " lbs. " lbs. " lbs. 24" " " lbs. " lbs. " lbs. N/A N/A. 6 May-2015 | 1302 39th St NW, Fargo, ND 58102 | 701-282-7655 | 800-747-7655 | Fax: 701-282-2887. C900. u ANSI/AWWA C900 WATER TRANSMISSION pipe | Gasketed Joint Specifications (14" - 24"). Northern pipe Products PVC gasketed ANSI/AWWA C900 PVC water transmission pipe is manufactured with gasketed joints conforming to the specifications of ASTM D3139. The rubber gaskets are manufactured to conform to the requirements of ASTM F477.

7 Northern pipe Products employs the Rieber Gasket System. The Rieber joining system is a factory made locked-in flexible elastomeric seal. The gasket is installed in the bell race during the manufacture of the joint. It should not be removed for any reason, as destruction of the joint will occur. u LOCKED-IN GASKET JOINT. B C. D A. Gasket Groove (Race) Outside Diameter E B. Lip Length A. C. Gasket Groove (Race) Length D. Overall Joint E. Spigot Insertion Depth DIMENSIONS (IN.). NOMINAL. pipe SIZE (A). (C) (E). (IN.) GASKET GROOVE (B) (D). GASKET GROOVE SPIGOT INSERTION. (RACE) OUTSIDE LIP LENGTH OVERALL JOINT. (RACE) LENGTH DEPTH. DIAMETER. 14" " " " " ". 16" " " " " ". 18" " " " " ". 20" " " " " ". 24" " " " " ". 7. C900. u C900 | Truckload Data NOMINAL pipe pipe OUTSIDE FEET PER PIECES PER FEET PER. SIZE (IN.) DIAMETER (IN.) PALLET PALLET TRUCKLOAD.

8 4" " 580' 29 pcs. 16,240'. 6" " 560' 28 pcs. 6,720'. 8" " 200' 10 pcs. 4,000'. 10" " 240' 12 pcs. 2,880'. 12" " 120'/160' 6 pcs. 1,960'. 14" " 120' 6 pcs. 1,440'. 16" " 40'/60' 2 pcs. 1,000'. 18" " 60'/80' 3 pcs. 800'. 20" " 80' 4 pcs. 640'. 24" " 60' 3 pcs. 360'. 8 May-2015 | 1302 39th St N, Fargo, ND 58102 | 701-282-7655 | 800-747-7655 | Fax: 701-282-2887. Gasketed SEWER pipe u PVC GRAVITY SEWER pipe | Gasketed pipe Specifications Northern pipe Products PVC Gasketed SEWER pipe 4 through 15 meets all dimensional and physical specifications of ASTM D3034. 18 through 24 SEWER pipe meets all dimensional and physical specifications of ASTM F679. 4 through 24 SDR-35 SEWER pipe products are available with the CSA (Canadian Standards Association) mark of acceptance. All Gasketed SEWER pipe is manufactured to laying lengths. u ASTM D3034 | Gasketed SEWER pipe SDR-35 (PS 46) SDR-26 (PS 115).

9 NOMINAL pipe OUTSIDE. POUNDS PER FOOT POUNDS PER FOOT. pipe SIZE DIAMETER MINIMUM MINIMUM. (IN.) (IN.) WALL WALL. (IN.) 14' 20' (IN.) 14' 20'. LENGTH LENGTH LENGTH LENGTH. 4 " .120" lbs. lbs..162" lbs. lbs. 6 " .180" lbs. lbs..241" lbs. lbs. 8 " .240" lbs. lbs..323" lbs. lbs. 10 " .300" lbs. lbs..404" lbs. lbs. 12 " .360" lbs. lbs..481" lbs. lbs. 15 " .437" lbs. lbs..588" lbs. lbs. Note: 4 and 6 diameter SDR-28 with the Canadian Standards Association mark of acceptance is available on special order. u ASTM F679 | Gasketed SEWER pipe SDR-35 (PS 46) SDR-26 (PS 115). NOMINAL pipe OUTSIDE. POUNDS PER FOOT POUNDS PER FOOT. pipe SIZE DIAMETER MINIMUM MINIMUM. (IN.) (IN.) WALL WALL. (IN.) 14' 20' (IN.) 14' 20'. LENGTH LENGTH LENGTH LENGTH. 18" " .536" lbs. lbs..720" lbs. lbs. 21" " .632" lbs. N/A .849" lbs. N/A. 24" " .709" lbs. N/A.

10 954" lbs. N/A. 9. Gasketed SEWER pipe u PVC GRAVITY SEWER pipe | Gasketed Joint Specifications Northern pipe Products PVC Gasketed SEWER pipe is manufactured with gasketed joints conforming to ASTM. D3212. The rubber gaskets are manufactured to conform to the requirements of ASTM F477 (Standard Specification for Elastomeric Seals for Joining Plastic pipe ). Northern pipe Products employs the Rieber Gasket System. The Rieber joining system is a factory made locked-in flexible elastomeric seal. The gasket is installed in the bell race during manufacture of the joint. It should not be removed for any reason, destruction of the joint occurs. u LOCKED-IN GASKET JOINT. B C. D A. Gasket Groove (Race) Outside Diameter E B. Lip Length A. C. Gasket Groove (Race) Length D. Overall Joint E. Spigot Insertion Depth DIMENSIONS (IN.). NOMINAL.