Silbrade & Silcon - NewAge Industries

1 Silbrade & SilconSilicone Hose & tubing Fluid Transfer Specialists Silbrade Braid Reinforced Silicone Open mesh polyester braiding incorporated within the walls of silicone tubing Raw materials meet FDA requirements per FDA 21 CFR for usewith food contact surfaces Reusable will withstand repeated sterilization^ Translucent natural color for visual contact with the flow Able to resist extreme temperature variation: -99 F to 350 F Odorless, tasteless, and inert Excellent weatherability properties resists , ozone, gases, mois-ture, and extreme temperatures Offers far higher pressure capabilities than similarly-sized unreinforced silicone tubing Listed by the National Sanitation Foundation (NSF-51) for food equipment materials Free of BPA, latex and phthalates.

2 REACH and RoHS compliant NotesThe construction of Silbrade enables siliconetubing to handle increased pressure offers outstanding resistance to tempera-ture extremes and is made from raw materials thatmeet FDA flexible design and construction of Silbrade also allows excellent bend radii and permits instal -lation in restricted spaces without impeding , a peroxide-cured product, contains nosulphur or other acid-producing chemicals therebyeliminating the possibility of staining, corro ding, ordeteriorating other materials it contacts. It is alsoresistant to ozone and over long time is recommended in the selection of fittings and clamps, as sharp barbed fittings orunlined metal clamps could tear into the hose walland possibly cause a failure, especially at elevatedpressures.

3 ^ Silbrade may be low pressure steam sterilized in-line or autoclaved at up to 250 F in anormal autoclaving cycle. However, if exposed torepeated steam sterilization or long-term high tem-perature or pressure, silicone will eventually relaxand become gummy. It should then be is not recommended forimplantable or in-body uses or for continuoussteam Properties**Hardness, Shore A 5 Liner 70 Hardness, Shore A 5 Cover 60 Tensile Strength, psi 1460 Elongation at Break, % 320 Tear Resistance, Die B, ppi 100 Modulus at 100%, psi 415 Brittle Temperature, F -99 Maximum Operating Temperature.

4 F 350**Values listed are typical for the material used in manufacture except where noted, apply to the hose linerexcept where noted, and are meant only as a guide to aid indesign. Field testing should be performed to find the actualvalues for your PER100 AT 70 F 233 216 208 183 166 141 116 91 75ID(IN.)1/83/161/45/163/81/25/83/41OD(I N.) .365 .447 .520 .592 .655 .800 . (FT.)10010010010010050, 100505050 PART NO. 290 0072 290 0149 290 0226 290 0303 290 0380 290 0457 290 0534 290 0611 290 0765 Recommended Fittings & Clamps Thermobarb barbed fittings Oetiker ear type clamps Kwik Clamp nylon double bond hose clamps Worm gear clamps WALL(IN.)

5 Coils are available; charges apply call for length suffix to part number when ordering. Example: 100 ft. of 1/8 x .365 is part number 290 pressures are calculated from burst testing using a 3:1 safety factor. Applicationtesting is indicates the critical dimension for fittings in Services Color Hardness Overbraid And MoreCall for more information: 800-506-3924 or215-526-2300 Cut SizeSilicone FT. AT 70 F*10201015102025282020520201510520151010 101010151055101055510510ID(IN.)1/161/163 /323/321/81/81/81/85/325/323/163/163/163 /161/41/41/41/45/165/163/83/83/83/87/161 /21/21/21/25/85/85/85/83/43/4OD(IN.)

6 1/83/165/327/323/161/45/163/89/3211/321/ 45/163/87/165/163/87/161/27/161/21/29/16 5/83/45/85/811/163/47/83/413/167/8111-1/ 8 STANDARDLENGTH (FT.)10010010010010010010010010010010010 0100100100100100100100100100100100100100 1001001001001001001001005050 PART 0084280 0161280 0315280 0392280 0469280 0546280 0623280 0700280 0854280 0931280 1008280 1085280 1162280 1239280 1393280 1470280 1547280 1624280 1778280 1855280 1932280 2009280 2086280 2163280 2240280 2317280 2394280 2471280 2548280 2625280 2702280 2779280 2856280 3087280 3164 Add length suffix to part number when ordering. Example: 100 ft. of 1/16 x 1/8 is part number 280 pressures are calculated from burst testing using a 3:1 safety factor. Application testing is indicates the critical dimension for fittings most outstanding properties of Silcon are itsflexibility and resistance to temperature extremes.

7 These,plus its good electrical properties and ability to self-extinguish, make Silcon an excellent choice for appli-ances and Silcon contains no sulphur or otheracid-producing chemicals, thereby eliminating the possi-bility of staining, corroding, or deteriorating materials itcontacts. It is extremely resistant to ozone and overlong time is recommended in the selection of fittings andclamps for Silcon as sharp barbed fittings or unlinedmetal clamps could tear into the tubing wall and possi-bly cause a failure.^ Silcon may be low pressure steam sterilized in-line orautoclaved at up to 250 F in a normal autoclaving , if exposed to repeated steam sterilization orlong-term high temperature or pressure, silicone will even-tually relax and become gummy.

8 It should then for industrial applications are availablethrough minimum order call for is not recommended for implantable or in-body uses or for continuous steam Properties**Hardness, Shore A 5 50 Tensile Strength, psi 1444 Elongation at Break, % 608 Tear Resistance, Die B, ppi 125 Modulus at 100%, psi 186 Brittle Temperature, F -100 Max. Operating Temperature, F 500 Max.

9 Operating Temperature for NSF, F 350**Values listed are typical for the material used in manufacture,except where noted, and are meant only as a guide to aid indesign. Field testing should be performed to find the actual valuesfor your application. Raw materials meet FDA requirements per FDA 21 CFR foruse with food contact surfaces Able to resist extreme temperature variation: -100 F to 500 F (350 Fmaximum for NSF applications) Translucent natural color for visual contact with the flow Resilient, stretchable, and resistant to compression set Reusable will withstand repeated sterilization^ Odorless, tasteless, and inert Good electrical and weatherability properties resists , ozone, gases, and moisture Listed by the National Sanitation Foundation (NSF-51) for food equipment materials Free of BPA, latex and phthalates.

10 REACH and RoHS compliant Made in Services Cut Size Color Hardness And MoreCall for more information: 800-506-3924 or215-526-2300 Recommended Fittings & Clamps Thermobarb barbed fittings Oetiker ear type clamps Kwik Clamp nylon double bond hose clamps Worm gear clamps Platinum cured for the highest degree of purity NSF-51 listed for food equipment materials Odorless, tasteless, and inert Open mesh polyester braiding incorporated within walls of silicone offersincreased pressure capabilities Able to resist extreme temperature variation: -100 F to 400 FSilbrade PlatinumPlatinum Cured Silicone Hose Platinum cured for the highest degree of purity (least extractables) Manufactured under good manufacturing practices in a controlled environment Reusable will withstand repeated sterilization Applications include pharmaceutical, biomedical, health and beauty, food, andbeverage handlingSilcon Med-XPlatinum Cured Medical Grade Silicone tubing Open mesh polyester braiding incorporated within the walls of silicone tubing Finished product meets USP Class VI requirements Able to resist extreme temperature variation.