Site Safety Information - Home | Bremik Construction

1 1026 SE Stark St Portland, OR 97214 Ph: Fx: site Safety Information The following documents must be submitted to Bremik Construction prior to beginning work. For additional Information please refer to the attached examples or contact Bremik s main office at Hazard Communication (MSDS) Material Safety Data Sheets (MSDS) should outline all hazardous material (chemicals) that will be used for your scope of work. MSDS sheets are to be submitted to Bremik Construction prior to beginning your work. Please see MSDS example attached to this document. Job Hazard Analysis Bremik Construction will provide a Job Hazard Analysis (JHA) for you to fill out and complete on a weekly basis or as your daily job tasks change.

2 Subcontractors may use their own JHA but this document must provide the same or similar Information as shown on the attached document. All JHA s will be completed on a weekly basis and submitted to Bremik s site supervisor upon completion. site Specific Safety Plan Guideline This document outlines the basic site Specific Safety Plan requirements for each jobsite. The site Specific Safety Plan should identify all hazards associated with your scope of work and provide safe work practices and personnel protection methods. Please see site Specific Safety Plan example attached to this document. 1026 SE Stark St Portland, OR 97214 Ph: Fx: site Specific Safety Plan Contents Guideline The site Specific Safety Plan should be a review of all work tasks and expected hazards associated with the project.

3 The contractor should review all tasks and hazards and provide a brief analysis on how the contractor will address each hazard in a safe and timely manner. Contractors are required to submit site Specific Safety Plans to the General Contractor prior to beginning work and shall update the site Specific Safety Plan as drawings and work scopes develop throughout the entire duration of the project. Note: Contractors must include and address all checklist items in writing prior to performing work onsite. See site Specific Safety Plan Checklist Below site Specific Safety Plan Checklist Contractors Name Brief description of Subcontractors Safety Policy General description of the objective of this document site Information (Project Address) Project Duration Key Personnel (Project Manager, Project Engineer, Superintendent, Safety Officer, Forman, Etc) Project Specifics (Scope of Work, site Conditions, site Surroundings, Etc) Health and Safety Responsibilities (Project Manager, Superintendent, Safety Officer, Forman, Employees, Etc) Brief description of subcontractors Safety Standards.

4 Items should include but is not limited to: Safety Meetings, New Hire Orientation, Drug and Alcohol Policy, PPE, Housekeeping, Assured Grounding Program, JHA, Hot Work, Hazard Communication Job Hazard Analysis for the work being performed Resources (Medical, Fire, Chemical, Administration) Traffic Control (General Traffic Provisions, Public Right-Away) Emergency (Emergency Protocol, Emergency Map, Emergency Numbers) Nearest Fire Department Fall Protection Plan Employee Training MSDS Inventory 1 site Specific Safety Plan Project General Information Bremik s Policy: The Safety and well being of each employee and customer is Bremik s number one priority and we are committed to providing a safe and healthful work environment.

5 Objective: The objective of this document is to establish a plan for implementing the company Safety program at the _____ project. This plan is intended to minimize losses, meet regulatory compliance requirements and implement site Safety regulations established by Bremik Construction along with OSHA standards. site Information : Project Duration: Duration of Project Key Personnel: Project Manager: Superintendent: Foreman: Project Engineer: Safety Officer: Project Specifics 2 Scope of Project: Remodel of an existing 4 story, 113,000 SF high school to commercial use. Includes demolition of some interior elements, new MEPFS systems, new elevator, new hardscape and parking lot, and new interior finishes.

6 site Conditions: site work includes a new hardscapes between the building and public sidewalk on the north and east elevations. New hardscape between the building and existing plaza on the west side. The south side includes a new sidewalks and new parking lot. site Surroundings: The Construction site is located within a mix use neighborhood so special considerations must be taken. Public Safety is first priority and the perimeter of the site is fenced off to ensure this. Noise, dust and trash pollution will be kept to a minimum by working designated hours (7:00am-6:00pm), implementing dust control and maintaining good housekeeping on and around site . Construction parking will be in issue as their will be no onsite parking and street parking is already tight in this area.

7 It is important to encourage crews to carpool to reduce parking impact to the neighborhood. Health and Safety Responsibilities Bremik Team: Project Manager Coordinate pre-planning meetings for project Safety . To ensure that Safety and Health issues are managed with the same priority as production and quality and when they conflict, Safety will take priority. Dedicate project resources for Safety . Superintendent- Implement Bremik s Safety program and policy. Promote accident prevention through constant communication and leading by example. Conduct weekly Safety meetings. Provide and maintain all Safety meeting minutes. Identify hazards and advise on proper and approved Safety guards and PPE.

8 Conduct new employee Safety orientation. Aid in scheduling/coordinating pre-planning meetings for the projects. Require, maintain and review all subcontractor JHA s for completeness and knowledge. Require all subcontractors/employees to comply with health and Safety regulations. Maintain copies of Bremik s Safety manual, OSHA book/forms and other applicable programs on site . Foreman Implement Bremik s Safety program and policy. Identify and correct hazards. Aid in conducting weekly Safety meetings. Notify superintendent of any and all Safety concerns in timely fashion. 3 Project Engineer Assist in coordinating pre-planning meetings for project Safety . Implement Bremik s Safety program and policy.

9 Conduct weekly Safety meetings. Monitor Safety performance on the project through observation, inspection, corrective action and documentation. Participate in post-accident investigations. Maintain copies of Bremik s Safety manual, OSHA book/forms and other applicable programs on site . Safety Officer Act as a resource to the company for Safety issues. Develop and maintain the Safety training program. Assist in project Safety planning. Conduct routine inspections of job sites. Employees: Attend new hire orientation and complete Safety /orientation checklists. To work in a safe manner at all times and comply with all Safety rules, procedures and requirements. To report all accidents, near misses and unsafe conditions, no matter the severity.

10 Attend Safety meetings. Subcontractors: Provide a site specific plan prior to any work commencing. To work in a safe manner at all times and comply with all Safety rules, procedures and requirements. To report all accidents, near misses and unsafe conditions, no matter the severity. Provide MSDS for ALL chemicals brought on site . Attend weekly Safety meetings. Provide weekly JHA s on a timely basis. Bremik Safety Standards Safety Meetings Project team will hold a weekly Safety every Monday morning at 7:00am. Attendance of all persons on site is mandatory. The meeting topics, discussion and attendees will be documented and kept in the Bremik Job Office trailer. New Hire Orientation - Each new hire will be required to attend a new hire orientation prior to being assigned to work so they are aware of the job specifics and Safety guidelines.